CPChristel Pierlot

Christel Pierlot

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Christel Pierlot has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of emulsification step on calcium carbonate encapsulated eicosane and incorporation into geopolymer

    by Y. Boland, G. Fontaine, S. Bourbigot, C. Pierlot

    The effect of the emulsification process of the organic n‐eicosane as a phase change material (PCM) in an aqueous solution of sodium dodecyl sulfate (SDBS) as a surfactant has been studied regarding the properties of the CaCO3 microcapsules. Such microcapsules aim to limit interactions between the PCM and the matrix (i.e., leakage and unwanted reactions). Optical and scanning electron microscopy (SEM) shows that the mean size of the n‐eicosane capsule is of the order of 5 μm. However, large non‐spherical objects which could be clusters of flocculated capsules or the results of encapsulation of coalescing n‐eicosane droplets, are observed, particularly when mechanical stirring (MS) is used rather than when an ultra‐turrax (UT) or sonotrode (S) is used in the initial emulsification step. These large, partially encapsulated objects could be the cause of the poor results in leakage tests. It is possible to encapsulate n‐eicosane inside a calcium carbonate shell, with a greater than 50% encapsulation ratio. The yield of encapsulated n‐eicosane measured by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) is similar and shows that 55% n‐eicosane core in CaCO3 shell can be produced. Up to 33 wt.% CaCO3 microcapsules (with 55% n‐eicosane content) have been successfully incorporated into fresh geopolymer paste. This incorporation of 18% (55% × 33%) of PCM does not modify the hardening conditions of the geopolymer since demolding was possible after 2 days at room temperature. DSC curves confirm that the melting reaction with n‐eicosane is conserved inside the hardened geopolymer.


  • Open Access

    Exploring the Efficiency of Algerian Kaolinite Clay in the Adsorption of Cr(III) from Aqueous Solutions: Experimental and Computational Insights

    by Karima Rouibah, Hana Ferkous, Meniai Abdessalam-Hassan, Bencheikh Lehocine Mossab, Abir Boublia, Christel Pierlot, Amdjed Abdennouri, Ivalina Avramova, Manawwer Alam, Yacine Benguerba, et al.

    The current study comprehensively investigates the adsorption behavior of chromium (Cr(III)) in wastewater using Algerian kaolinite clay. The structural and textural properties of the kaolinite clay are extensively characterized through a range of analytical methods, including XRD, FTIR, SEM-EDS, XPS, laser granulometry, N2 adsorption isotherm, and TGA–DTA. The point of zero charge and zeta potential are also assessed. Chromium adsorption reached equilibrium within five minutes, achieving a maximum removal rate of 99% at pH 5. Adsorption equilibrium is modeled using the Langmuir, Freundlich, Temkin, Elovich, and Dubinin–Radushkevitch equations, with the Langmuir isotherm accurately describing the adsorption process and yielding a maximum adsorption capacity of 8.422 mg/g for Cr(III). Thermodynamic parameters suggest the spontaneous and endothermic nature of Cr(III) sorption, with an activation energy of 26.665 kJ/mol, indicating the importance of diffusion in the sorption process. Furthermore, advanced DFT computations, including COSMO-RS, molecular orbitals, IGM, RDG, and QTAIM analyses, are conducted to elucidate the nature of adsorption, revealing strong binding interactions between Cr(III) ions and the kaolinite surface. The integration of theoretical and experimental data not only enhances the understanding of Cr(III) removal using kaolinite but also demonstrates the effectiveness of this clay adsorbent for wastewater treatment. Furthermore, this study highlights the synergistic application of empirical research and computational modeling in elucidating complex adsorption processes.


  • Open Access

    Adsorption of Orange G Dye on Hydrophobic Activated Bentonite from Aqueous Solution

    by Zohra Taibi, Kahina Bentaleb, Zohra Bouberka, Christel Pierlot, Maxence Vandewalle, Christophe Volkringer, Philippe Supiot, Ulrich Maschke

    This report focusses on the modification of physical structure and chemical properties of a bentonite clay from the Hammam Boughrara region of the Maghnia district in western Algeria to maximize its adsorption capacity. The purified bentonite clay (called B) was modified, either by acid activation with 1M sulfuric acid (B-Act), or by intercalation with the cationic surfactant cetytrimethyl ammonium bromide (CTAB), applying a cation exchange capacity (CEC) of 100% (called B-CTAB). Modification of B was also introduced by combining these two steps consecutively, i.e., at first acid activation of B, followed by intercalation with CTAB (B-Act-CTAB). The B-Act-CTAB was obtained by H2SO4 (1M) acid activation, followed by co-adsorption of CTAB with 100% and 300% of the CEC of B-Act as precursor. In particular, a strong increase of surface area and pore volume of the modified bentonites was observed for B-Act (469.83 m²/g and 0.401 cm3g−1), B-Act-CTAB100 (267.72 m²/g and 0.316 cm3 g−1) and B-Act-CTAB300 (111.15 m²/g and 0.171 cm3g−1), compared to B (31.79 m²/g and 0.074 cm3 g−1) and B-CTAB (3.79 m²/g and 0.034 cm3 g−1), respectively. The bentonite-based adsorbents were then used to evaluate the removal efficiency of an organic molecule, the azo dye Orange G (OG), as a model for a Persistent Organic Pollutant. Freundlich, Langmuir and Sips (Langmuir–Freundlich) models were applied to analyze equilibrium isotherms, showing a good correlation between experimental data and the Freundlich model. A good agreement was obtained between experimentally obtained kinetic adsorption data and the pseudo-second-order model, allowing to evaluate rate constants. B-Act-CTAB300 can be applied as a low-cost material for removal of azo dyes, since its adsorption capacity towards OG (102.80 mg/g) exceeds largely that of B-CTAB (31.49 mg/g) and B-Act-CTAB100 (12.77 mg/g).


  • Open Access

    Development of a TiO2/Sepiolite Photocatalyst for the Degradation of a Persistent Organic Pollutant in Aqueous Solution

    by Amina Bakhtiar, Zohra Bouberka, Pascal Roussel, Christophe Volkringer, Ahmed Addad, Baghdad Ouddane, Christel Pierlot, Ulrich Maschke

    A clay-based TiO2 nanocomposite material was synthesized by a facile method, to investigate its structure and photocatalytic efficiency. The supported TiO2 nanoparticles were generated using a sol-gel method, and subsequently, mixed with a suspension of sepiolite. The material was recovered in powder form (Mc-80) and then calcined to properly arrange the crystal lattice of the TiO2 particles for use in heterogeneous photocatalysis (Mc-80-500). A powder X-ray diffractogram of Mc-80-500 revealed a dispersion of anatase and rutile phase TiO2 particles on the clay surface, exhibiting a size in the order of 4–8 nm. TEM images of Mc-80-500 confirmed the presence of isolated TiO2 beads on the surface of the fibrous sepiolite. The specific surface area of Mc-80-500 was larger than that of raw sepiolite and that of free TiO2 nanoparticles. Mc-80-500 was found to be more efficient in heterogeneous photocatalysis compared to other TiO2 materials based on sepiolite. Total depollution of a reactive dye (Orange G) was achieved after 1 h irradiation time, which is relatively quick compared to previous reports. The photocatalyst material can be washed with distilled water without chemical additives or calcination, and can be reused several times for photocatalysis, without loss of efficiency.


  • Influence of cetyltrimethylammonium bromide and hydroxide ions on the interfacial tension and stability of emulsions of dodecane in aqueous silicate solutions

    by Matthieu Bertin, Donatien Gomes Rodrigues, Christel Pierlot, Cyrille Albert-Mercier, Catherine Davy, David Lambertin, Véronique Nardello-Rataj


  • Open Access

    Self-Stratification of Ternary Systems Including a Flame Retardant Liquid Additive

    by Agnes Beaugendre, Stephanie Degoutin, Severine Bellayer, Christel Pierlot, Sophie Duquesne, Mathilde Casetta, Maude Jimenez

    Particular coating compositions based on incompatible polymer blends can produce coatings having complex layered structures after film formation. The most traditional approaches to their structural modification are the introduction of additives (extenders, inorganic pigments, surface active agents, etc.). As minor additives, some are capable of substantially accelerating the phase separation process with a moderate or negligible influence on the composition equilibrium of solutions. In contrast, in order to be effective, some have to be introduced in significant amounts, thereby substantially changing the resulting distribution of components through the film. Up to now, most of the liquid additives that have been tested destabilized the solutions while impacting the layering process. In this work, two phosphorus based liquid fillers have been introduced (at 2.5 and 5 wt.%) in a partially incompatible polymer blend based on a silicone resin and a curable epoxy resin to fire retard a polycarbonate matrix. Self-stratification was evidenced by microscopic and chemical analyses, flammability by Limiting Oxygen Index (LOI) and UL-94 tests, fire performances by Mass Loss Calorimetry and thermal stability by using a tubular furnace and ThermoGravimetric Analysis. The ternary compositions including 5 wt.% of additives exhibit the best stratification and excellent adhesion onto polycarbonate. Improvements of the fire resistant properties were observed (+7% for the LOI compared to the virgin matrix) when a 200 µm wet thick coating was applied, due to reduced flame propagation and dripping.