GholamReza Havaei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
GholamReza Havaei has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Abolfazl Eslami
Department of Civil and Environmental Engineering, Amirkabir University of Technology, Tehran, Iran
4 shared publications - Yazdan Hayati
Department of Civil and Environmental Engineering, Amirkabir University of Technology, Tehran, Iran
4 shared publications Abolghassem Keramati
Department of Civil and Environmental Engineering, Amirkabir University of Technology, No. 424, Hafez St., Enghelab Av., Tehran, Iran
1 shared publicationMatteo Filippi
Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Torino, Italy
1 shared publicationSeyyed Amirhossein Moayyedi
Structural Engineering Research Center International Institute of Earthquake Engineering and Seismolog (IIEES) Tehran Iran
1 shared publication
Latest Publications
- 13 February 2023
- Published by Wiley in Structural Concrete
- Vol. 24 (4) , 5349-5369
Numerical evaluation of seismically retrofitted bridge concrete column under extreme loading
Columns have the most important role for overall stability of bridges and these elements are the most vulnerable structural components under extreme loading too. Therefore, studying and improving the performance of these elements under such loads has attracted widespread attention among researchers. The main objective of this paper is investigating the performance of bridge reinforced concrete columns which seismically retrofitted by steel or CFRP jacketing under blast load via finite element method. The finite element models' assumptions in Abaqus FE software are verified using the correlated experimental data from literature and good agreements have been obtained. Parametric studies are conducted to cover a wide range of factors including transverse and longitudinal reinforcement ratios, blast load intensity, type and thickness of conventional seismic retrofitting jacket. The results reveal that the longitudinal reinforcement ratio presents more effects on decreasing extreme loading demands than the transverse reinforcing. Moreover, utilizing seismically retrofitting jacket, especially CFRP jacket, tend to be an effective way to reduce demands of reinforced concrete column under extreme loading, where its effectiveness increases, in case of more severe events. Also, the current seismic damage state and performance level, can predict the damage level of columns in good agreement with the design specifications.
- 13 February 2023
- Published by Wiley in Structural Concrete
- Vol. 24 (4) , 5349-5369
Numerical evaluation of seismically retrofitted bridge concrete column under extreme loading
Columns have the most important role for overall stability of bridges and these elements are the most vulnerable structural components under extreme loading too. Therefore, studying and improving the performance of these elements under such loads has attracted widespread attention among researchers. The main objective of this paper is investigating the performance of bridge reinforced concrete columns which seismically retrofitted by steel or CFRP jacketing under blast load via finite element method. The finite element models' assumptions in Abaqus FE software are verified using the correlated experimental data from literature and good agreements have been obtained. Parametric studies are conducted to cover a wide range of factors including transverse and longitudinal reinforcement ratios, blast load intensity, type and thickness of conventional seismic retrofitting jacket. The results reveal that the longitudinal reinforcement ratio presents more effects on decreasing extreme loading demands than the transverse reinforcing. Moreover, utilizing seismically retrofitting jacket, especially CFRP jacket, tend to be an effective way to reduce demands of reinforced concrete column under extreme loading, where its effectiveness increases, in case of more severe events. Also, the current seismic damage state and performance level, can predict the damage level of columns in good agreement with the design specifications.
- 23 November 2021
- Published by Taylor & Francis in Waves in Random and Complex Media
- Vol. 34 (5) , 1-18
Asymmetric 3D stress- and flux-induced wave propagation in transversely isotropic thermoelastic solids by using of analytical methods
Asymmetric 3D wave propagation in transversely isotropic thermoelastic solids is presented by using of potential functions and integral transforms. Governing equations of thermoelastodynamic boundary-value problem (TBVP) are including three equations of motion and an energy equation which make a set of four coupled partial differential equations (PDE) in terms of displacements and temperature. By using of the displacement- and temperature-potential function relationships, four coupled equations of TBVP are reduced to two uncoupled PDEs governing the potential functions which are of sixth and second orders. To solve these uncoupled PDEs, complex Fourier expansions and Hankel integral transforms are used in this paper to suppress the angular and radial variables respectively in cylindrical coordinate system. Consequently, sixth and second order ordinary differential equations (ODE) in terms of depth are received. By solving ODEs, satisfying the radiation and boundary conditions and applying the Hankel inverse transforms, the displacement and temperature functions have been determined in the real space. To validate the analytical and numerical results, some comparisons have been made with the results presented in the literature where excellent agreements have been observed. Important points have been mentioned about speed of SH, SV, P and Rayleigh waves in transversely isotropic and isotropic thermoelastic solids.
- 23 November 2021
- Published by Taylor & Francis in Waves in Random and Complex Media
- Vol. 34 (5) , 1-18
Asymmetric 3D stress- and flux-induced wave propagation in transversely isotropic thermoelastic solids by using of analytical methods
Asymmetric 3D wave propagation in transversely isotropic thermoelastic solids is presented by using of potential functions and integral transforms. Governing equations of thermoelastodynamic boundary-value problem (TBVP) are including three equations of motion and an energy equation which make a set of four coupled partial differential equations (PDE) in terms of displacements and temperature. By using of the displacement- and temperature-potential function relationships, four coupled equations of TBVP are reduced to two uncoupled PDEs governing the potential functions which are of sixth and second orders. To solve these uncoupled PDEs, complex Fourier expansions and Hankel integral transforms are used in this paper to suppress the angular and radial variables respectively in cylindrical coordinate system. Consequently, sixth and second order ordinary differential equations (ODE) in terms of depth are received. By solving ODEs, satisfying the radiation and boundary conditions and applying the Hankel inverse transforms, the displacement and temperature functions have been determined in the real space. To validate the analytical and numerical results, some comparisons have been made with the results presented in the literature where excellent agreements have been observed. Important points have been mentioned about speed of SH, SV, P and Rayleigh waves in transversely isotropic and isotropic thermoelastic solids.
- 28 October 2021
- Published by Taylor & Francis in Journal of Thermal Stresses
- Vol. 44 (11) , 1366-1388
3D asymmetric dynamic Green’s functions of a thermoelastic transversely isotropic solid by a method of potentials
A theoretical formulation is presented for the displacements, temperature and stresses in a 3 D transversely isotropic thermoelastic solid under arbitrary mechanical loads and heat flux. By using two scalar potential functions, 3 D patch-load, patch-heat source, point-load and point-heat source Green’s functions are given for the displacements, temperature and stresses. Basic governing equations of coupled thermoelasticity in transversely isotropic solids are presented in the cylindrical coordinates system. By means of two scalar potential functions, the four coupled governing equations for this class of problems are uncoupled into a 6th order and a 2nd order partial differential equations. Applying the Fourier expansions and Hankel transforms, the angular and radial variables are suppressed and 6th and 2nd order ordinary differential equations are obtained. By solving the ordinary differential equations, the potential functions, displacements, temperature and stresses are obtained in the Fourier-Hankel transformed space. By applying the Hankel inversion theorem, all responses are presented in the physical time-spatial space. To prove the validity of the analytical and numerical solutions, our results are compared with existing solutions reported in the literature. Numerical results are also included to show the effects of material anisotropy, elastic and thermal properties; and frequency of excitation on the responses.
- 28 October 2021
- Published by Taylor & Francis in Journal of Thermal Stresses
- Vol. 44 (11) , 1366-1388
3D asymmetric dynamic Green’s functions of a thermoelastic transversely isotropic solid by a method of potentials
A theoretical formulation is presented for the displacements, temperature and stresses in a 3 D transversely isotropic thermoelastic solid under arbitrary mechanical loads and heat flux. By using two scalar potential functions, 3 D patch-load, patch-heat source, point-load and point-heat source Green’s functions are given for the displacements, temperature and stresses. Basic governing equations of coupled thermoelasticity in transversely isotropic solids are presented in the cylindrical coordinates system. By means of two scalar potential functions, the four coupled governing equations for this class of problems are uncoupled into a 6th order and a 2nd order partial differential equations. Applying the Fourier expansions and Hankel transforms, the angular and radial variables are suppressed and 6th and 2nd order ordinary differential equations are obtained. By solving the ordinary differential equations, the potential functions, displacements, temperature and stresses are obtained in the Fourier-Hankel transformed space. By applying the Hankel inversion theorem, all responses are presented in the physical time-spatial space. To prove the validity of the analytical and numerical solutions, our results are compared with existing solutions reported in the literature. Numerical results are also included to show the effects of material anisotropy, elastic and thermal properties; and frequency of excitation on the responses.
- 9 April 2021
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 29 (25) , 3773-3793
3D soil-structure interaction analysis with a combined substructure-FEM under external forces and seismic waves
This paper presents a simple methodology for studying soil-structure interaction problems. Based on the substructure approach, the unbounded soil beneath the foundation has been removed. The foundation's impedance matrix and the driving force vector due to seismic waves have been applied to the superstructure. Foundation-soil impedance functions have been reproduced by utilizing sets of springs and dashpots with elastic and damping frequency-dependent properties. The superstructures have been discretized with refined finite beam elements derived with the Carrera Unified Formulation. Vertical, horizontal, rocking and torsional vibrations of the superstructure-soil system have been investigated by considering soft, intermediate, stiff and rigid soils. Displacement and stress values of the flexible-base superstructures have been compared with those obtained for the fixed-base configuration. For validation purposes, the obtained results have been assessed with solutions available in the literature and with those provided by the ASCE-7 building code. In all cases, significant agreements have been observed. Higher-modes frequencies and responses have been obtained for the flexible-base superstructures which could be very useful for modal analyses including SSI effects.
- 9 April 2021
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 29 (25) , 3773-3793
3D soil-structure interaction analysis with a combined substructure-FEM under external forces and seismic waves
This paper presents a simple methodology for studying soil-structure interaction problems. Based on the substructure approach, the unbounded soil beneath the foundation has been removed. The foundation's impedance matrix and the driving force vector due to seismic waves have been applied to the superstructure. Foundation-soil impedance functions have been reproduced by utilizing sets of springs and dashpots with elastic and damping frequency-dependent properties. The superstructures have been discretized with refined finite beam elements derived with the Carrera Unified Formulation. Vertical, horizontal, rocking and torsional vibrations of the superstructure-soil system have been investigated by considering soft, intermediate, stiff and rigid soils. Displacement and stress values of the flexible-base superstructures have been compared with those obtained for the fixed-base configuration. For validation purposes, the obtained results have been assessed with solutions available in the literature and with those provided by the ASCE-7 building code. In all cases, significant agreements have been observed. Higher-modes frequencies and responses have been obtained for the flexible-base superstructures which could be very useful for modal analyses including SSI effects.
- 10 May 2019
- Published by Springer Nature in Acta Mechanica
- Vol. 230 (8) , 2751-2769
Complete general solution for Lord–Shulman generalized thermoelastodynamics by using potential functions for transversely isotropic solids
- 10 May 2019
- Published by Springer Nature in Acta Mechanica
- Vol. 230 (8) , 2751-2769
Complete general solution for Lord–Shulman generalized thermoelastodynamics by using potential functions for transversely isotropic solids
- 7 September 2017
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 27 (3)
Assessment of sliding‐rubber isolator effect in progressive collapse of bridges under two scenarios
Summary: In this study, performances of 2 types of bridges, with and without seismic isolation, are addressed in 2 damage analysis scenarios, where, in the first, the side column and, in the second, the middle column are removed from the bridge piers. The performance was assessed using nonlinear dynamic analysis, and the time history and maximum structural responses were evaluated. Initially, sliding‐rubber isolators were designed according to AASHTO guide specifications, and then the bridges were modeled in OpenSees software package. Additionally, the coefficient of friction for the isolator was considered as a variable due to sudden removal of the columns and the consequent changes in the sliding velocity and axial forces. The results indicate that use of seismic isolation systems caused an increase in all maximum structural responses except that of the base shear. Considering the frictional performance of the isolators, slides in the deck are not caused by yielding of seismic isolators, and the reason for permanent displacements of the deck may be attributed to bridge instabilities in the first scenario. However, decrease in the horizontal stiffness results in increased maximum permanent displacement. In the first scenario, uplift of the deck occurred in the case of isolated bridge.
- 7 September 2017
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 27 (3)
Assessment of sliding‐rubber isolator effect in progressive collapse of bridges under two scenarios
Summary: In this study, performances of 2 types of bridges, with and without seismic isolation, are addressed in 2 damage analysis scenarios, where, in the first, the side column and, in the second, the middle column are removed from the bridge piers. The performance was assessed using nonlinear dynamic analysis, and the time history and maximum structural responses were evaluated. Initially, sliding‐rubber isolators were designed according to AASHTO guide specifications, and then the bridges were modeled in OpenSees software package. Additionally, the coefficient of friction for the isolator was considered as a variable due to sudden removal of the columns and the consequent changes in the sliding velocity and axial forces. The results indicate that use of seismic isolation systems caused an increase in all maximum structural responses except that of the base shear. Considering the frictional performance of the isolators, slides in the deck are not caused by yielding of seismic isolators, and the reason for permanent displacements of the deck may be attributed to bridge instabilities in the first scenario. However, decrease in the horizontal stiffness results in increased maximum permanent displacement. In the first scenario, uplift of the deck occurred in the case of isolated bridge.