ILIn-Young Lee

In-Young Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


In-Young Lee has a total of 31 co-authors. Here are the top co-authors by number of shared publications:

  • Jinho Ko

    PHYCHIPS Inc., Daejeon, Republic of Korea

    3 shared publications
  • Sang-Gug Lee

    School of Electrical Engineering, Korea Advanced Institute of Science and Technology, Daejeon, South Korea

    3 shared publications
  • Sang-Sung Lee

    Department of Information and Communications Engineering, Korea Advanced Institute of Science and Technology, Daejeon, Republic of Korea

    3 shared publications
  • Donggu Im

    Division of Electronics Engineering Chonbuk National University Jollabuk‐do 561‐756 Korea

    2 shared publications
  • Donggu Im

    Division of Electronic Engineering, Jeonbuk National University, Jeonju, Jeollabuk-do, South Korea

    2 shared publications
  • Jeongki Choi

    Department of Information and Communications Engineering, Korea Advanced Institute of Science and Technology, Daejeon, Republic of Korea

    2 shared publications

Latest Publications

  • ULP Sliding-IF Receiver With 25% Duty Passive Mixer and Enhanced LO Feed-Through Rejection

    by Hyun-Gi Seok, Keun-Mok Kim, Sang-Gug Lee, In-Young Lee, Geunhaeng Lee

    This article reports a high-sensitivity ultralow-power receiver (RX) for a long-distance Internet of Thing (IoT) applications. In the RX front end, current reused two-stage low-noise amplifier (LNA) and first mixer that enhances local oscillator (LO) feed-through rejection (FTR) is proposed. The second mixer employs a passive configuration that operates as a 25% mixer, based on a 50% duty cycle LO signal, thereby further minimizing current consumption. Additionally, an analysis of the impact of switching sequence on conversion gain in the passive mixer is presented. Implemented in 65-nm CMOS achieves the sensitivity of −102 dBm at a 0.1%-bit error rate and less than −50-dB carrier-to-interferer ratio (CIR) at 5-MHz offset while consuming $466~\mu $ W from a 0.6-V supply.

  • Open Access

    Data-Driven Non-Linear Current Controller Based on Deep Symbolic Regression for SPMSM

    by Muhammad Usama, In-Young Lee

    This study designs a simple current controller employing deep symbolic regression (DSR) in a surface-mounted permanent magnet synchronous machine (SPMSM). A novel DSR-based optimal current control scheme is proposed, which after proper training and fitting, generates an analytical dynamic numerical expression that characterizes the data. This creates an understandable model and has the potential to estimate data that have not been seen before. The goal of this study was to overcome the traditional linear proportional–integral (PI) current controller because the performance of the PI is highly dependent on the system model. Moreover, the outer speed control loop gains are tuned using the cuckoo search algorithm, which yields optimal gain values. To demonstrate the efficacy of the proposed design, we apply the control design to different test cases, that is varied speed and load conditions, as well as sinusoidal speed reference, and compare the results with those of a traditional vector control design. Compared with traditional control approaches, we deduce that the DSR-based control design could be extrapolated far beyond the training dataset, laying the foundation for the use of deep learning techniques in power conversion applications.


  • An Analog Baseband Spectrum Sensing Circuit Employing Voltage Follower-Based Multiorder Channel Selection Filters

    by Seohyeong Jeong, Dongmin Kim, In-Young Lee, Donggu Im

    An analog baseband (ABB) spectrum sensing circuit is proposed for fast spectrum sensing. Contrast to the conventional RF scanner where it takes a relatively long period to detect channel and interference condition by sequentially controlling the center frequency of the filter, the proposed ABB circuit can scan it at a time using different bandwidths of lowpass filters with an almost equal out-of-band attenuation slope to sense the powers and frequencies of channel and interference. The ABB circuit is composed of two chains of five cascaded real and complex low-pass filters. The cut-off frequencies of five cascaded low-pass filters are set to be 10, 8, 6, 4 and 2 MHz respectively, regarding the channel bandwidth of 2 MHz. The orders of the five filters are optimized to be 4th, 4th, 3rd, 2nd, and 2nd order respectively to make the rejected out-of-band power same for each filter for accurate detection. The filter core is designed on the basis of a flipped voltage follower and a super source follower for a low power dissipation and a high linearity, and the low power technique for implementing high-order filter is newly proposed in the design of filter chain. The measured frequency response at each output of the filter chain was almost the same to the simulation result. The measurement results show a noise figure (NF) of 19.2 dB, 22.1 dB, 24.8 dB, 25.1 dB, and 27 dB for each filters, and an in-band input-referred third-order intercept point (IIP3) of 9.2 dBm, 7.2 dBm, and 15.7 dBm at the output of 1st, 3rd, and last stages. The total power consumption of the filter chain is 10.4 mW from a 1.2 V supply voltage.


  • A Fully Integrated 490-GHz CMOS Receiver Adopting Dual-Locking Receiver-Based FLL

    by Kyung-Sik Choi, Keun-Mok Kim, Dzuhri Radityo Utomo, In-Young Lee, Sang-Gug Lee

    A fully integrated 490-GHz receiver (RX) adopting a dual-locking receiver-based FLL (DL-RBFLL) is presented. The proposed RBFLL structure saves the power consumption by reusing the existing blocks in RX instead of the power-hungry blocks such as dividers and buffers operating at sub-THz. Contrary to the single-loop implementation, the dual-loop RBFLL, which consists of the coarse and fine locking loops, extends the locking range by six times with negligible additional power dissipation. In the RF front-end (FE), the proposed 2nd-order sub-harmonic mixer (SHM) enhances interport isolation and suppresses the undesired LO leakage using a simple passive network. In the IF path, a 2-stage low-noise amplifier (LNA) followed by a 10-stage programmable gain amplifier provides a controllable gain of 0–80 dB with 4-dB step. An N-path filter, which serves as a high-Q bandpass noise filter, improves SNR in the IF path and thus RX sensitivity. Implemented in a 65-nm CMOS, the 490-GHz RX achieves the measured noise figure of 51.1 dB and noise equivalent power (NEP) of 0.85 pW/Hz $^{0.5}$ for the noise bandwidth of 17 MHz. The estimated sensitivity of the proposed RX is −92.9 dBm for a 1 kHz noise bandwidth, which dissipates 31.8 mW from a 1.2-V supply.


  • Open Access

    A self-powered glucose sensor based on BioCapacitor principle with micro-sized enzyme anode employing direct electron transfer type FADGDH

    by Inyoung Lee, Junko Okuda-Shimazaki, Wakako Tsugawa, Kazunori Ikebukuro, Koji Sode

    Diabetes mellitus is a disorder in which the body does not produce enough or respond normally to insulin; consequently, blood glucose levels increase to become abnormally high. Accordingly, the primary treatment of diabetes is to control glycemic levels continuously. To continuously control glycemic levels, several medical devices have been developed to monitor blood glucose levels, represented by sensors and monitors for the self-monitoring of blood glucose. The ultimate goal for those engaged in research to develop medical devices is to develop implantable biodevices, namely self-powered autonomously operated artificial pancreas systems. One of the most challenging issues in realizing an implantable artificial pancreas is the long-term continuous supply of electricity, which is currently dependent on rechargeable batteries, requiring periodical replacement. In this work, we report the development of a direct electron transfer type enzyme-based miniaturized self-powered glucose sensor based on the BioCapacitor principle with a micro-sized enzyme anode area (0.15 mm × 0.75 mm), which has only 0.1 mm2 of electrode surface. As a result, a BioCapacitor utilizing a biofuel cell with a micro-sized enzyme anode was operated by self-power. In addition, the glucose concentration was detected within the range from 13 mM to 100 mM based on the frequency of charge/discharge cycles of the BioCapacitor. Although further improvement of the current density of the micro-sized anode is necessary to monitor a glucose concentration range lower than 13 mM, this self-powered glucose sensor with a micro-sized electrode based on the BioCapacitor principle was operated continuously for 6.6 h at 37 °C in 100 mM potassium phosphate buffer (pH 7.0). Our success indicates the potential to realize self-powered, autonomous, and implantable sensing modules for bio devices such as glucose-sensing systems for an artificial pancreas.


  • Open Access

    Low‐power SOI CMOS antenna switch driver circuit with RF leakage suppression and fast switching time

    by I.‐Y. Lee, D. Im

    A low‐power antenna switch driver circuit with RF leakage suppression and fast switching time is implemented in a 0.25 μm silicon‐on‐insulator (SOI) CMOS process. It is composed of a three‐stage current starved ring oscillator with a clock buffer, a charge pump and a latch‐based three‐state logic driver. The negative voltage from the charge pump is fed into the latch‐based three‐state logic driver, and it generates three states of logic level (+VDD, GND and −VDD) according to the decoder signal without any reliability issue. In addition, the proposed three‐state logic driver with an optimal negative resistance value reduces the amount of the RF leakage coupling into the charge pump while maintaining its switching time fast. In the measurement, the designed switch driver circuit shows P1dB ) and 140 ns of switching time while allowing 30 dB of isolation over 100 MHz to 3 GHz frequency range.


  • A 1.9‐GHzsilicon‐on‐insulatorCMOSstacked‐FETpower amplifier with uniformly distributed voltage stresses

    by Donggu Im, Kuduck Kwon, In‐Young Lee

    Summary: A 1.9‐GHz single‐stage differential stacked‐FET power amplifier with uniformly distributed voltage stresses was implemented using 0.32‐μm 2.8‐V thick‐oxide MOSFETs in a 0.18‐μm silicon‐on‐insulator CMOS process. The input cross‐coupled stacked‐FET topology was proposed to evenly distribute the voltage stresses among the stacked transistors, alleviating the breakdown and reliability issues of the stacked‐FET power amplifier in sub‐micrometer CMOS technology. With a 4‐V supply voltage, the proposed power amplifier with an integrated output coupled‐resonator balun showed a small‐signal gain of 17 dB, a saturated output power of 26.1 dBm, and a maximum power‐added efficiency of 41.5% at the operating frequency. Copyright © 2017 John Wiley & Sons, Ltd.


  • A 50–450 MHz Tunable RF Biquad Filter Based on a Wideband Source Follower With > 26 dBm IIP$_{3}$, +12 dBm P$_{1{\rm dB}}$, and 15 dB Noise Figure

    by In-Young Lee, Donggu Im, Jinho Ko, Sang-Gug Lee

    This paper reports a source follower-based active RC filter topology for RF front-ends in wideband systems. In the proposed active RC filter, the noise figure and bandwidth are improved through adopting the proposed sub-1 Ω Z out source follower, which replaces the conventional operational amplifier-based unity gain buffer and through simply changing its location in the filter. Applying the proposed scheme to the conventional Sallen-Key filter also improves the stopband rejection performance. Furthermore, the proposed filter topology ultimately suppresses the DC offset voltage and flicker noise of the unity gain buffer, which is the only active circuit in the filter. The proposed biquad filter is implemented in 0.18 μm CMOS and the measurements exhibit >26 dBm IIP 3 , +12 dBm input P 1dB , and 15 dB noise figure over 50-450 MHz of a 6 bit tunable frequency range. The proposed biquad filter consumes 14 mA from a 1.8 V supply and the chip occupies 1000 ×500 μm 2 .


  • Spur Reduction Techniques With a Switched-Capacitor Feedback Differential PLL and a DLL-Based SSCG in UHF RFID Transmitter

    by In-Young Lee, Seungjin Kim, Sang-Sung Lee, Jeongki Choi, Jinho Ko

    This paper presents a robust spur reduction technique using a switched-capacitor feedback differential phase-locked loop (PLL) and a delay-locked-loop (DLL)-based spread-spectrum clock generation in a UHF-band RF identification transmitter (TX). The proposed differential PLL is characterized by adopting a switched-capacitor common-mode feedback and distributed varactor biasing scheme to the differential charge pump and voltage-controlled oscillator designs, respectively, which results in down to 94 dBc in reference spur rejection with all digital parts off. Additionally, by adopting an 8-bit DLL and Hershey-Kiss modulated profile together, the proposed spread-spectrum clock generator shows more than 20-dB electromagnetic-interference reduction while providing up-, down-, and center-spread modes. Implemented in a 0.18m CMOS process, the proposed TX achieves <; - 80-dBc spur suppression with 25-dBm transmit power at 920 MHz, which complies with the most stringent regulatory spectral mask without a surface acoustic wave filter.