Xu Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xu Yang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Xianfei Ding
AECC Beijing Institute of Aeronautical Materials, Beijing 100095, China
3 shared publications Guojian Hao
2 shared publications- Junpin Lin
University of Science and Technology Beijing
2 shared publications Yongfeng Liang
2 shared publications- Guojian Hao
Beijing Research Institute of Mechanical & Electrical Technology, Beijing 100083, China
1 shared publication Junpin Lin
1 shared publication
Latest Publications
- 1 October 2018
- Published by Elsevier in Applied Surface Science
- Vol. 455, 144-152
Ni-doped Al2O3 coatings prepared by cathode plasma electrolysis deposition on Ti-45Al-8.5 Nb alloys
- 1 October 2018
- Published by Elsevier in Applied Surface Science
- Vol. 455, 144-152
Ni-doped Al2O3 coatings prepared by cathode plasma electrolysis deposition on Ti-45Al-8.5 Nb alloys
- Open Access
Influence of Solvent and Electrical Voltage on Cathode Plasma Electrolytic Deposition of Al2O3 Antioxidation Coatings on Ti-45Al-8.5Nb Alloys
Al2O3 coatings were prepared on Ti-45Al-8.5Nb alloys via cathodic plasma electrolysis deposition (CPED) in both 1.2 M Al(NO3)3 aqueous and ethanolic solutions. Different voltages were also applied during the deposition process to optimize coating properties. Coatings deposited in both solutions mainly consisted of γ-Al2O3, with some Al(OH)3 found in coatings prepared in aqueous solution. Coatings prepared in ethanol solution exhibited better oxidation resistance at 900 °C as well as better substrate adhesion, which was mainly due to smaller crater sizes on coating surfaces. The deposition process was discussed in detail and the reason for the smaller craters examined. The results suggested that solution surface tension mainly influenced the average diameter of hydrogen bubbles that formed on cathode surfaces during the process. Smaller bubbles lead to both lower current densities on cathodes and smaller crater sizes on coatings.
Open AccessInfluence of Solvent and Electrical Voltage on Cathode Plasma Electrolytic Deposition of Al2O3 Antioxidation Coatings on Ti-45Al-8.5Nb Alloys
Al2O3 coatings were prepared on Ti-45Al-8.5Nb alloys via cathodic plasma electrolysis deposition (CPED) in both 1.2 M Al(NO3)3 aqueous and ethanolic solutions. Different voltages were also applied during the deposition process to optimize coating properties. Coatings deposited in both solutions mainly consisted of γ-Al2O3, with some Al(OH)3 found in coatings prepared in aqueous solution. Coatings prepared in ethanol solution exhibited better oxidation resistance at 900 °C as well as better substrate adhesion, which was mainly due to smaller crater sizes on coating surfaces. The deposition process was discussed in detail and the reason for the smaller craters examined. The results suggested that solution surface tension mainly influenced the average diameter of hydrogen bubbles that formed on cathode surfaces during the process. Smaller bubbles lead to both lower current densities on cathodes and smaller crater sizes on coatings.
- 1 September 2017
- Published by Elsevier in Surface and Coatings Technology
- Vol. 325, 30-38
Effect of power supply on the deposition of Zn on a steel substrate using cathodic plasma electrolysis
- 1 September 2017
- Published by Elsevier in Surface and Coatings Technology
- Vol. 325, 30-38
Effect of power supply on the deposition of Zn on a steel substrate using cathodic plasma electrolysis