George Pashos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
George Pashos has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Andreas G. Boudouvis
National Technical University of Athens
2 shared publications - George Kokkoris
National Technical University of Athens
2 shared publications - Antony N. Spyropoulos
School of Chemical Engineering, National Technical University of Athens, Athens 15780, Greece
1 shared publication - Athanasios G. Papathanasiou
School of Chemical Engineering, National Technical University of Athens, 15780 Athens, Greece
1 shared publication - George Pantazopoulos
ELKEME Hellenic Research Centre for Metals S.A., 61st km Athens—Lamia National Road, 32011 Oinofyta, Greece
1 shared publication - Ioannis Contopoulos
Research Center for Astronomy and Applied Mathematics, Academy of Athens
1 shared publication
Latest Publications
- 29 April 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (20) , 6793-6802
Optimization of Patterned Surfaces for Improved Superhydrophobicity through Cost-Effective Large-Scale Computations
The pattern design of superhydrophobic surfaces can be significantly aided by computations that predict the Cassie-Baxter (CB) to Wenzel (W) transition, which is responsible for the break-down of superhydrophobic behavior. We present a computational framework for the optimization of patterned surfaces, based on the energy barriers of the CB-W transitions that comprises the following elements: a) Design of structured surface patterns, e.g. arrays of pillars, with parameterized geometric features such as size, pitch, slope and roundness. b) Computation of the wetting states with a modified Young-Laplace equation that facilitates the introduction of solid-liquid interactions for complex surface patterns and has significantly lower computational cost than other commonly used methods, such as the volume-of-fluid, phase-field, etc. c) Incorporation of the modified Young-Laplace in the simplified string method, allowing the calculation of the minimum energy paths (MEPs) of wetting transitions, which apart from the energy barriers, also reveal the transition mechanisms (CB failure modes). d) Accommodation of large-scale problems with good parallel performance and scalability, on multi-core distributed memory systems, using fast iterative solvers and the Message Passing Interface (MPI) communication protocol. We demonstrate the computational framework, with a shape optimization study of inverted conical frustum pillars. The optimization objective function is the resistance to the CB-W transition, which is quantified by the energy barrier – a relatively large energy barrier suggests improved superhydrophobicity. We also report the parallel performance, in terms of parallel speedup for problems ranging from three hundred thousands to twelve million degrees of freedom, solved using up to forty processing cores.
- 29 April 2019
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 35 (20) , 6793-6802
Optimization of Patterned Surfaces for Improved Superhydrophobicity through Cost-Effective Large-Scale Computations
The pattern design of superhydrophobic surfaces can be significantly aided by computations that predict the Cassie-Baxter (CB) to Wenzel (W) transition, which is responsible for the break-down of superhydrophobic behavior. We present a computational framework for the optimization of patterned surfaces, based on the energy barriers of the CB-W transitions that comprises the following elements: a) Design of structured surface patterns, e.g. arrays of pillars, with parameterized geometric features such as size, pitch, slope and roundness. b) Computation of the wetting states with a modified Young-Laplace equation that facilitates the introduction of solid-liquid interactions for complex surface patterns and has significantly lower computational cost than other commonly used methods, such as the volume-of-fluid, phase-field, etc. c) Incorporation of the modified Young-Laplace in the simplified string method, allowing the calculation of the minimum energy paths (MEPs) of wetting transitions, which apart from the energy barriers, also reveal the transition mechanisms (CB failure modes). d) Accommodation of large-scale problems with good parallel performance and scalability, on multi-core distributed memory systems, using fast iterative solvers and the Message Passing Interface (MPI) communication protocol. We demonstrate the computational framework, with a shape optimization study of inverted conical frustum pillars. The optimization objective function is the resistance to the CB-W transition, which is quantified by the energy barrier – a relatively large energy barrier suggests improved superhydrophobicity. We also report the parallel performance, in terms of parallel speedup for problems ranging from three hundred thousands to twelve million degrees of freedom, solved using up to forty processing cores.
- Open Access
A Comprehensive CFD Model for Dual-Phase Brass Indirect Extrusion Based on Constitutive Laws: Assessment of Hot-Zone Formation and Failure Prognosis
A numerical method for the precise calculation of temperature, velocity and pressure profiles of the α-β brass indirect hot extrusion process is presented. The method solves the Navier–Stokes equations for non-Newtonian liquids with strain-rate and temperature-dependent viscosity that is formulated using established constitutive laws based on the Zener–Hollomon type equation for plastic flow stress. The method can be implemented with standard computational fluid dynamics (CFD) software, has relatively low computational cost, and avoids the numerical artifacts associated with other methods commonly used for such processes. A response surface technique is also implemented, and it is thus possible to build a reduced order model that approximately maps the process with respect to all combinations of its parameters, including the extrusion speed and brass phase constitution. The reduced order model can be a very useful tool for production, because it instantaneously provides important quantities, such as the average pressure or the temperature of hot-spots that are formed due to the combined effect of die/billet friction and the generation of heat from plastic deformation (adiabatic shear deformation heating). This approach can assist in the preliminary evaluation of the metal flow pattern, and in the prediction and prevention of critical extrusion failures, thus leading to subsequent process and product quality improvements.
Open AccessA Comprehensive CFD Model for Dual-Phase Brass Indirect Extrusion Based on Constitutive Laws: Assessment of Hot-Zone Formation and Failure Prognosis
A numerical method for the precise calculation of temperature, velocity and pressure profiles of the α-β brass indirect hot extrusion process is presented. The method solves the Navier–Stokes equations for non-Newtonian liquids with strain-rate and temperature-dependent viscosity that is formulated using established constitutive laws based on the Zener–Hollomon type equation for plastic flow stress. The method can be implemented with standard computational fluid dynamics (CFD) software, has relatively low computational cost, and avoids the numerical artifacts associated with other methods commonly used for such processes. A response surface technique is also implemented, and it is thus possible to build a reduced order model that approximately maps the process with respect to all combinations of its parameters, including the extrusion speed and brass phase constitution. The reduced order model can be a very useful tool for production, because it instantaneously provides important quantities, such as the average pressure or the temperature of hot-spots that are formed due to the combined effect of die/billet friction and the generation of heat from plastic deformation (adiabatic shear deformation heating). This approach can assist in the preliminary evaluation of the metal flow pattern, and in the prediction and prevention of critical extrusion failures, thus leading to subsequent process and product quality improvements.
- 26 June 2018
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 14 (29) , 6090-6101
Computational investigation of actuation mechanisms of droplets on porous air-permeable substrates
We study the actuation of droplets on porous substrates by air that permeates through pores.
- 26 June 2018
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 14 (29) , 6090-6101
Computational investigation of actuation mechanisms of droplets on porous air-permeable substrates
We study the actuation of droplets on porous substrates by air that permeates through pores.