Tomoya Kawabata
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tomoya Kawabata has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Tetsuya Tagawa
Steel Research Laboratory, JFE Steel Corporation
5 shared publications - A. Takumi Ozawa
National Maritime Research Institute, Tokyo, Japan
3 shared publications - Fuminori Yanagimoto
Department of Systems Innovation, The University of Tokyo
3 shared publications Shuji Aihara
3 shared publications- Yoshiki Mikami
Joining and Welding Research Institute, Osaka University
3 shared publications Chenjun Yu
2 shared publications
Latest Publications
- Open Access
- 29 September 2026
- Published by Elsevier in Materials & Design
- Vol. 271
Mechanistic insights into supercritical CO2 corrosion via interpretable Kolmogorov-Arnold networks
- 29 September 2026
- Published by Elsevier in Materials & Design
- Vol. 271
Open AccessMechanistic insights into supercritical CO2 corrosion via interpretable Kolmogorov-Arnold networks
- Open Access
- 27 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 270
Experimental and Hutchinson–Rice–Rosengren field analysis of J-integral resistance in pre-strained SUS316L at cryogenic temperatures
- 27 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 270
Open AccessExperimental and Hutchinson–Rice–Rosengren field analysis of J-integral resistance in pre-strained SUS316L at cryogenic temperatures
- Open Access
- 7 May 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 42, 7224-7239
Constitutive modeling of metastable austenitic stainless steel at cryogenic temperatures: A secant method approach considering stress triaxiality
- 7 May 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 42, 7224-7239
Open AccessConstitutive modeling of metastable austenitic stainless steel at cryogenic temperatures: A secant method approach considering stress triaxiality
- Open Access
- 28 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Strain dependence of retained austenite to martensite transformation in 13%Ni steel and numerical study of its effect on hydrogen diffusion
- 28 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessStrain dependence of retained austenite to martensite transformation in 13%Ni steel and numerical study of its effect on hydrogen diffusion
- Open Access
- 25 September 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 165
Fracture resistance and splitting mechanism in aluminum alloy 5083-O at cryogenic temperatures
- 25 September 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 165
Open AccessFracture resistance and splitting mechanism in aluminum alloy 5083-O at cryogenic temperatures
- Open Access
- 15 December 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (14) , 2042-2050
Ductility Loss of a Metastable Austenitic Stainless Steel and Its TIG Weldment Due to Hydrogen Embrittlement at Low Temperatures Considering the Effect of Pre-strain at 4 K
The amount of martensite in austenitic stainless steels produced during plastic deformation at low temperatures is related to the reduction in hydrogen embrittlement resistance. A pre-strain at 4 K was employed in this work to produce strain-induced martensite (SIM) in the microstructure of SUS316L and its weldment to verify the changes in hydrogen embrittlement susceptibility through slow strain tensile (SSRT) tests in a high-pressure hydrogen environment. As the base metal specimens, the weld metal specimens, manufactured by gas tungsten arc welding (GTAW or TIG) were pre-strained at different levels (5%, 10%, and 15%) for comparison with the non-pre-strained condition. Analysis of the most degraded samples tested from -150 °C to 0 °C is conducted through fracture surface observations, lateral crack length measurement, and crack densities. It was possible to indicate that the pre-strain effect induced earlier crack nucleation in comparison to the situation observed in the non-pre-strained material. Moreover, the pre-existing martensite produced by the pre-strain at 4 K is responsible for earlier crack nucleation, leading to a loss in the hydrogen embrittlement resistance for the SSRT pre-strained base metal specimens.
- 15 December 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (14) , 2042-2050
Open AccessDuctility Loss of a Metastable Austenitic Stainless Steel and Its TIG Weldment Due to Hydrogen Embrittlement at Low Temperatures Considering the Effect of Pre-strain at 4 K
The amount of martensite in austenitic stainless steels produced during plastic deformation at low temperatures is related to the reduction in hydrogen embrittlement resistance. A pre-strain at 4 K was employed in this work to produce strain-induced martensite (SIM) in the microstructure of SUS316L and its weldment to verify the changes in hydrogen embrittlement susceptibility through slow strain tensile (SSRT) tests in a high-pressure hydrogen environment. As the base metal specimens, the weld metal specimens, manufactured by gas tungsten arc welding (GTAW or TIG) were pre-strained at different levels (5%, 10%, and 15%) for comparison with the non-pre-strained condition. Analysis of the most degraded samples tested from -150 °C to 0 °C is conducted through fracture surface observations, lateral crack length measurement, and crack densities. It was possible to indicate that the pre-strain effect induced earlier crack nucleation in comparison to the situation observed in the non-pre-strained material. Moreover, the pre-existing martensite produced by the pre-strain at 4 K is responsible for earlier crack nucleation, leading to a loss in the hydrogen embrittlement resistance for the SSRT pre-strained base metal specimens.
- 28 August 2023
- Published by Springer Nature in Welding in the World
- Vol. 67 (10) , 2315-2322
Improvement of local compression condition for fracture toughness test with Bayesian optimization
- 28 August 2023
- Published by Springer Nature in Welding in the World
- Vol. 67 (10) , 2315-2322
Improvement of local compression condition for fracture toughness test with Bayesian optimization
- 19 October 2022
- Published by Springer Nature in Welding in the World
- Vol. 67 (3) , 607-615
Local compression process avoiding toughness change
- 19 October 2022
- Published by Springer Nature in Welding in the World
- Vol. 67 (3) , 607-615
Local compression process avoiding toughness change
- 28 March 2022
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 50 (3) , 1657-1672
Assessment Criteria for Pop-Ins Generated in Welded Joints Subjected to Fracture Toughness Testing
A pop-in (a brittle crack arrest phenomenon) sometimes occurs in a three-point bending fracture toughness test of a welded joint. The current standards may consider a pop-in to be a significant fracture and underestimate fracture toughness. In this case, the allowable defect size in a welded structure becomes very small, and many defects need to be repaired, resulting in high maintenance costs. Therefore, a reasonable acceptance judgment method for the pop-in is practically important. Herein we proposed an assessment method to determine whether or not it is a significantly detrimental pop-in that affects the integrity of a structure. The method was designed based on the cohesive zone model and validated on its ability to reproduce experimental results. The difference in loading modes between bending during the fracture toughness test and tension of the structure and in the crack initiation conditions for both load modes was determined by comparing the Weibull stress, which is a characteristic of the material. All the main fracture surfaces of the numerical model were cohesive and had conservatively low toughness. No pop-in occurred under tensile loading under a Weibull stress condition of 13.1 % load drop, whereas a pop-in occurred under bending loading. However, under a load drop of 10.6 %, a pop-in occurred even under tensile loading. Therefore, it was shown that the load drop could be relaxed to 10 % or more, although the load drop is considered insignificant at 5 % or more according to the current standards.
- 28 March 2022
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 50 (3) , 1657-1672
Assessment Criteria for Pop-Ins Generated in Welded Joints Subjected to Fracture Toughness Testing
A pop-in (a brittle crack arrest phenomenon) sometimes occurs in a three-point bending fracture toughness test of a welded joint. The current standards may consider a pop-in to be a significant fracture and underestimate fracture toughness. In this case, the allowable defect size in a welded structure becomes very small, and many defects need to be repaired, resulting in high maintenance costs. Therefore, a reasonable acceptance judgment method for the pop-in is practically important. Herein we proposed an assessment method to determine whether or not it is a significantly detrimental pop-in that affects the integrity of a structure. The method was designed based on the cohesive zone model and validated on its ability to reproduce experimental results. The difference in loading modes between bending during the fracture toughness test and tension of the structure and in the crack initiation conditions for both load modes was determined by comparing the Weibull stress, which is a characteristic of the material. All the main fracture surfaces of the numerical model were cohesive and had conservatively low toughness. No pop-in occurred under tensile loading under a Weibull stress condition of 13.1 % load drop, whereas a pop-in occurred under bending loading. However, under a load drop of 10.6 %, a pop-in occurred even under tensile loading. Therefore, it was shown that the load drop could be relaxed to 10 % or more, although the load drop is considered insignificant at 5 % or more according to the current standards.
- 8 June 2021
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 50 (1) , 656-673
Simplified Prediction Method of Stress Intensity Factor in Mid-thick Plane in 3D Cracked Body and Its Difference from 2D Handbook Formula
The authors have been working to improve the crack tip opening displacement (CTOD) evaluation standard as a fracture parameter for the cleavage-type brittle fracture critical condition of carbon steel. In 2016, WES1108, Standard Test Method for Crack-Tip Opening Displacement (CTOD) Fracture Toughness Measurement, which is the CTOD test standard in Japan, was revised, and subsequently, the CTOD calculation formula of ISO 15653:2010, Metallic Materials – Method of Test for the Determination of Quasistatic Fracture Toughness of Welds, was revised in 2018, focusing on the study of the formula that constitutes the basis of the standard. Similar to the original British Standards equation, the proposed CTOD calculation formula consists of a small-scale yield (SSY) term and a plastic term, but in the SSY term, the two-dimensional (2D) stress intensity factor (SIF) is used. The authors focused on the incorrectness of this treatment derived from the difference between 2D and three-dimensional (3D). Here, two accurate relationships have been explored through systematic finite element method analyses; one is the correlation of the 3D SIF values in the mid-thickness plane and 2D SIF, and the second is the relationship between the actual 3D SIF in mid-thickness and the CTOD in mid-thickness. The KI ratio (K3D/K2D) sharply coincides with the value 1.11, as inferred in several previous pieces of research in the idealistic infinite plate with a crack. However, if the ligament size is finite as in the actual fracture toughness test, the KI ratio drops significantly from 1.11, and in some cases, the KI ratio is less than 1. By unifying these findings, a new precise CTOD formula has been established. Lastly, the study inferred that the error of the calculation formula is improved, especially in small thickness regions, as compared with the current standard proposed in 2016 and 2018 by the authors.
- 8 June 2021
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 50 (1) , 656-673
Simplified Prediction Method of Stress Intensity Factor in Mid-thick Plane in 3D Cracked Body and Its Difference from 2D Handbook Formula
The authors have been working to improve the crack tip opening displacement (CTOD) evaluation standard as a fracture parameter for the cleavage-type brittle fracture critical condition of carbon steel. In 2016, WES1108, Standard Test Method for Crack-Tip Opening Displacement (CTOD) Fracture Toughness Measurement, which is the CTOD test standard in Japan, was revised, and subsequently, the CTOD calculation formula of ISO 15653:2010, Metallic Materials – Method of Test for the Determination of Quasistatic Fracture Toughness of Welds, was revised in 2018, focusing on the study of the formula that constitutes the basis of the standard. Similar to the original British Standards equation, the proposed CTOD calculation formula consists of a small-scale yield (SSY) term and a plastic term, but in the SSY term, the two-dimensional (2D) stress intensity factor (SIF) is used. The authors focused on the incorrectness of this treatment derived from the difference between 2D and three-dimensional (3D). Here, two accurate relationships have been explored through systematic finite element method analyses; one is the correlation of the 3D SIF values in the mid-thickness plane and 2D SIF, and the second is the relationship between the actual 3D SIF in mid-thickness and the CTOD in mid-thickness. The KI ratio (K3D/K2D) sharply coincides with the value 1.11, as inferred in several previous pieces of research in the idealistic infinite plate with a crack. However, if the ligament size is finite as in the actual fracture toughness test, the KI ratio drops significantly from 1.11, and in some cases, the KI ratio is less than 1. By unifying these findings, a new precise CTOD formula has been established. Lastly, the study inferred that the error of the calculation formula is improved, especially in small thickness regions, as compared with the current standard proposed in 2016 and 2018 by the authors.