Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jordi García-Amorós has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Silicon Effect on Conductive Behavior in Rubber Recycled Composites

    by Marc Marín-Genescà, Ramon Mujal Rosas, Jordi García Amorós, Lluis Massagues, Xavier Colom

    In the present research, the structure and thermal–dielectric behavior of Styrene Butadiene Rubber (SBR) and of the SBR/EPDMd composite with SiO2 with different compositions and concentrations of EPDMd are analyzed. In this sense, interesting behaviors are observed for the DC-AC regime of the conductive behavior of the material; therefore, a very marked DC and AC regime is observed in the conductivities, showing a different dielectric behavior at low and high frequencies. On the other hand, peak relaxations due to polarization phenomena are observed in terms of the imaginary modulus. Conductively, SiO2 does not produce significant or relevant changes, but it does produce changes in the permittivity and the electrical modulus, so it is concluded that the impact of the incorporation of SiO2 in these compounds affects energy storage (permittivity and modulus) in these types of compounds. Compared with compounds without silica (insights—no SiO2), it is observed that SiO2 maintains a similar operating regime to the initial one (SBR and SBR + EPDMd + SiO2) without SiO2 dielectric changes occurring, so silica presence modifies the dielectric behavior, reducing polarization effects, as can be seen in the dielectric results. Conductively, SiO2 produces more insulating compounds, that is, less conductive; this property can make it interesting as electrical insulation.


  • Open Access

    Influence of Tire Rubber Particles Addition in Different Branching Degrees Polyethylene Matrix Composites on Physical and Structural Behavior

    by Marc Marín-Genescà, Ramon Mujal Rosas, Jordi García Amorós, Lluis Massagues Vidal, Xavier Colom Fajula

    Waste from pneumatic wheels is one of the major environmental problems, and the scientific community is looking for methods to recycle this type of waste. In this paper, ground tire rubber particles (GTR) from disused tires have been mixed with samples of low-density polyethylene (LDPE) and high-density polyethylene (HDPE), and morphological tests have been performed using scanning electron microscopy (SEM), as well as the dynamic electric analysis (DEA) dielectric characterization technique using impedance spectroscopy. From this experience, how GTR reinforcement influences polyethylene and what influence GTR particles have on the branched polyethylene has been detected. For pure LDPE samples, a Debye-type dielectric behavior is observed with an imperfect semicircle, which depends on the temperature, as it shows differences for the samples at 30 °C and 120 °C, unlike the HDPE samples, which do not show such a trend. The behavior in samples with Debye behavior is like an almost perfect dipole and is due to the crystalline behavior of polyethylene at high temperature and without any reinforcement. These have been obtained evidence that for branched PE (LPDE) the Maxwell Wagner Sillars (MWS) effect is highly remarkable and that this happens due to the intrachain polarization effect combined with MWS. This means that the permittivity and conductivity at LDPE/50%GTR are high than LDPE/70%GTR. However, it does not always occur that way with HDPE composites in which HDPE/70%GTR has the highest values of permittivity and conductivity, due to the presence of conductive fraction (Carbon Black-30%) in the GTR particles and their dielectric behavior.


  • Open Access

    Study Analysis of Thermal, Dielectric, and Functional Characteristics of an Ethylene Polyethylene Diene Monomer Blended with End-of-Life Tire Microparticles Amounts

    by Marc Marín-Genescà, Ramon Mujal-Rosas, Jordi García-Amorós, Miguel Mudarra, Xavier Ramis Juan, Xavier Colom Fajula

    The recycling and disposal of disused tires is a topic of great concern to today’s companies, researchers, and society in general. In this sense, our research aims to recycle end-of-life tires (GTRs) through the separation of the fraction of vulcanized rubber from the other compounds in order to later grind this fraction and separate it into lower particle sizes. Finally, we aim to incorporate these GTR particles as a filler of an ethylene-polyethylene-diene monomer (EPDM). The obtained composites with EPDM and GTR are tested (5%, 10%, 20%) comparing these values with neat EPDM as a control sample. Thermal tests such as differential calorimetry (DSC) and thermogravimetric analysis (TGA) as well as dielectric tests (DEA) are performed in order to characterize these materials and check their viability as dielectric or semiconductor, for industrial use. It is checked how the presence of GTR increases functional properties such as conductivity/permittivity. The influence of temperature (40 to 120 °C) and addition of GTR particles in electrical properties has also been analyzed. The dielectric behavior of these composites is fully characterized, analyzing the different types of relaxation with increasing frequency (10 mHz to 3 MHz), using the electric modulus, and Argand diagrams among other measures. The influence of GTR and temperature in the dielectric and thermal behavior of these materials has been analyzed, where CB of GTR creates interfacial polarization phenomena in the dielectric behavior of the composite and increases the permittivity (real and imaginary) as well as the conductivity. Finally, with these obtained properties, the possible application of EPDM/GTR composites as industrial dielectrics has been studied.


  • Open Access

    Microparticle Size and Quantities Effect on the Mechanical Features of End of Life Tires in Thermoplastic Composites

    by Marc Marín-Genescà, Jordi García-Amorós, Ramon Mujal-Rosas, Lluís Massagués Vidal, Xavier Colom Fajula

    Currently, the huge use of tires generates large quantities of waste material which represents a severe environmental problem. The common technique used for processing waste tires is crushing using mechanical methods and separating tire components like fibers, metals, and rubber from the used tire. The aim of this research is the recycling of this rubber from crushed tires, called ground tire rubber (GTR). With this aim, the manuscript analyses key mechanical properties of the thermoplastic composites produced by blending of crushed and micronized small particles of waste rubber tires with several industrial thermoplastic polymers. These types of composites are defined based on the total amount GTR in percent by weight, in the composite, and also, the particle sizes used in each case, so these aforementioned two variables (microparticle size and amounts) along with seven common industrial polymers define a series of composites for which the mechanical properties were tested, studied, analyzed and finally presented. Finally, the results obtained show that this proposed recycling method could be a way to enhance some specific polymer properties and could contribute to reducing the total of end of life used tire stocks environmental problem.


  • Open Access

    Application Properties Analysis as a Dielectric Capacitor of End-of-Life Tire-Reinforced HDPE

    by Marc Marín-Genescà, Jordi García-Amorós, Ramon Mujal-Rosas, Lluís Massagués Vidal, Xavier Colom Fajula

    The purpose of the present research is to obtain waste of polymeric composite as an insulator capacitive application. Rubber materials, once they end their useful life, may be difficult to reuse or recycle. At present, research only uses one tire recycling method, which involves grinding and separating steel and fibers from vulcanized rubber, and then using the rubber particles for industrial capacitors. The methodology for this research is to compare the permittivity (ε′ and ε″) between high-density polyethylene (HDPE) and the polymer matrix compound, consisting of an HDPE polymeric matrix blended with end-of-life tire particles (ground tire rubber (GTR)), to analyze the feasibility of using such tires as electrically insulating materials (dielectrics). The incorporation of carbon black in the GTR compounds modifies conductivity; GTRs carry a significant amount of carbon black, and therefore some electrical properties may change significantly compared to highly insulating polymer substrates. The performed experimental study is based on a dynamic electric analysis (DEA) test developed in the frequency range of 10−2 Hz to 3 MHz and at different temperatures (from 35 to 70 °C) of different samples type: HDPE neat and HDPE compounds with 10%, 20% and 40% of GTR loads. A sample’s electrical behavior is checked for its dependence on frequency and temperature, focused on the permittivity property; this is a key property for capacitive insulators and is key for examining the possible applications in this field, for HDPE + GTR blends. Results for the permittivity behavior and the loss factor show different electrical behavior. For a neat HDPE sample, no dependence with frequency nor temperature is shown. However, with the addition of 10%, 20%, and 40% amount of GTR the HDPE compounds show different behaviors: for low frequencies, interfacial polarization relaxation is seen, due to the Maxwell–Wagner–Sillars (MWS) effect, performed in heterogeneous materials. In order to analyze thermal and morphological properties the differential scanning calorimetry (DSC) test and scanning electron microscopy (SEM) have been used. Results obtained show that adding waste tire particles in an HDPE matrix allows HDPE + 40% GTR blends to act as a dielectric in capacitors, increasing the capacitor dielectric efficiency in the low frequencies due to the MWS effect, which increases the dielectric constant.


  • Open Access

    Coupled inductors design of the bidirectional non‐inverting buck–boost converter for high‐voltage applications

    by Catalina González‐Castaño, Carlos Restrepo, Roberto Giral, Jordi García‐Amoros, Enric Vidal‐Idiarte, Javier Calvente

    This work analyses the effects on the efficiency of the winding‐to‐winding capacitance of the coupled‐inductor of the bidirectional non‐inverting buck–boost converter in high‐voltage applications. This converter presents many advantages that make it suitable for low‐voltage hard‐switching photovoltaic and fuel cell hybrid systems. However, experimental results obtained using the previously reported procedure to implement the coupled inductors show low‐efficiency in high‐voltage applications. A different implementation procedure of the coupled inductors, with lower winding‐to‐winding capacitance, is proposed. High‐efficiency experimental results from a 400 V 1.6 kW prototype have been achieved over a wide operating voltage range, thanks to the use of SiC devices and the modified coupled inductors, confirming in this way its good potential as a building block also in high‐voltage wide‐gain‐range applications.


  • Open Access

    Influence of Amounts and Particle Diameter on the Mechanical Properties of Several Polymeric Composites Reinforced with GTR Particles

    by Marc Marín Genescà, Jordi García-Amorós, Ramon Mujal-Rosas, Lluís Massagués, Xavier Colom

    Nowadays, the massive use of tires generates large stocks of waste material which is a serious environmental problem. The usual method used for processing wasted tires is mechanical crushing, in which fiber, steel, and rubber are separated. The aim of this research is the recycling of the obtained rubber, called also GTR (Ground Waste Tires). With this purpose, the paper analyses the mechanical properties of the composites produced by mixing GTR with several industrial polymers. These composites are characterized by the percentage of GTR in the composite and its particle size. These two variables along with seven industrial polymers define a set of composites from which the mechanical properties are analyzed and presented. From the results, it can be drawn that this proposal could be a way to enhance some polymer properties and to contribute in some way to reduce the environmental wasted tires problem.


  • Open Access

    Two-Phase Linear Hybrid Reluctance Actuator with Low Detent Force

    by Jordi Garcia-Amorós, Marc Marín-Genescà, Pere Andrada, Eusebi Martínez-Piera

    In this paper, a novel two-phase linear hybrid reluctance actuator with the double-sided segmented stator, made of laminated U cores, and an interior mover with permanent magnets is proposed. The permanent magnets are disposed of in a way that increases the thrust force of a double-sided linear switched reluctance actuator of the same size. To achieve this objective, each phase of the actuator is powered by a single H-bridge inverter. To reduce the detent force, the upper and the lower stator were shifted. Finite element analysis was used to demonstrate that the proposed actuator has a high force density with low detent force. In addition, a comparative study between the proposed linear hybrid reluctance actuator, linear switched reluctance, and linear permanent magnet actuators of the same size was performed. Finally, experimental tests carried out in a prototype confirmed the goals of the proposed actuator.


  • Open Access

    Linear Switched Reluctance Motors

    by Jordi Garcia-Amoros, Pere Andrada, Baldui Blanque

    This chapter deals with linear switched reluctance machines (LSRMs). Linear switched reluctance machines are the counterpart of the rotary switched reluctance machine (SRM), and now they have aroused great interest in the field of electrical machines and drives. In this chapter, first, a mathematical model is presented, and then a procedure for the design of this kind of machines is proposed. Next, a linear switched reluctance force actuator, based on the before designed procedure, is simulated. In addition, experimental proofs of the goodness of the design process and of the accuracy of the simulation of the linear switched reluctance force actuator are given.


  • Open Access

    Ground Tire Rubber Recycling in Applications as Insulators in Polymeric Compounds, According to Spanish UNE Standards

    by Marc Marín-Genescà, Jordi García-Amorós, Ramon Mujal-Rosas, Lluís Massagués Vidal, Jordi Bordes Arroyo, Xavier Colom Fajula

    In the present research, we investigated the conceivable outcomes of using ground tire rubber (GTR) particle polymeric blends. Special methods of restoring tires that are no longer in use include GTR retreading, GTR blending destined for recycling to attain raw substances utilized in other industrial application production processes, and the valorization of GTR for power/energy generation. The recycling of end-of-life tires enables the recovery of rubber, steel, and fibers, all of which are valid on the market as raw materials to be used for other processes. There are methods to recycle GTRs in a clean and environmentally friendly way. In the present research, several industrial applications of GTR polymer blends were developed and compared with standard values from the Spanish Association for Standardization (UNE) and the International Electrotechnical Commission (IEC). In order to analyze the viability in many of the industrial applications selected, certain compounds obtained from the GTR polymer blends were analyzed regarding their use in nine low requirement insulator applications. The research and analysis developed in this manuscript used standard values from the UNE and IEC, and these standard values were compared with the test values. The obtained results were used to provide an application list that could be helpful for industrial applications. In this research, the pre-owned polymers were as follows: polypropylene (PP), high-density polyethylene (HDPE), polystyrene (PS), acrylonitrile butadiene-styrene (ABS), ethylene vinyl acetate (EVA), polyvinyl chloride (PVC), and polyamide (PA). The filler used was GTR with particle sizes lower than 200 microns. The amounts of GTR particles in the compound materials were 0% (raw polymer), 5%, 10%, 20%, 40%, 50%, and 70% (the latter being found in polymeric blends). We discovered six plausible modern applications of GTR polymer blends as indicated by the UNE and IEC standards.