Gabriela Huminic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gabriela Huminic has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Angel Huminic
Mechanical Engineering Department, Transilvania University of Brasov, 29, Bulevardul Eroilor, 500036 Brasov, Romania
6 shared publications Angel Huminic
Transilvania Univ Brasov, Mech Engn Dept, 29 Blvd Eroilor, Brasov 500036, Romania
3 shared publicationsFlorian Dumitrache
Plasma and Radiation Physics, National Institute for Laser, Bucharest, Romania
2 shared publications- Alexandru Vărdaru
Mechanical Engineering Department 29, Transilvania University of Brasov, Bulevardul Eroilor, 500036 Brasov, Romania
1 shared publication - Alexandru-Mihai Iamandi
National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor Street, 077125 Magurele, Romania
1 shared publication Claudiu Fleaca
National Institute for Laser, Plasma and Radiation Physics, Bucharest, Romania
1 shared publication
Latest Publications
- Open Access
- 17 August 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (8) , 971
Multifunctional Properties of Nickel Nanoparticles Produced by Laser Ablation in Liquid
This study explores the multifunctional properties of Ni nanoparticles obtained by laser ablation in liquid, with emphasis on the potential use of these nanoparticles in different applications such as cooling fluids or photoelectrochemical ones. The Ni nanoparticles were synthesized by the laser ablation in liquid technique using an Nd-YAG laser and ultrapure water as liquid. The structural, dimensional, morphologic, and stoichiometric characterizations of the nanoparticles were performed using different techniques such as transmission electron microscopy (TEM), energy dispersive X-ray (EDS) and dynamic light scattering spectroscopy (DLS). Nickel nanoparticles with sizes ranging from 5 to 15 nm in diameter were obtained. The experimental measurements were performed to determine the thermal conductivity and viscosity of the obtained nanofluids, essential parameters in the evaluation of the cooling fluid performances. Loading TiO2 thin films with Ni nanoparticles led to the enhancement of the photoelectrochemical water splitting properties of TiO2 thin films, the Ni nanoparticles acting on the collecting, transferring and separating the photogenerated charges and ultimately improving the overall anodic and cathodic efficiencies. The results obtained can contribute to the development of innovative, multifunctional solutions based on non-precious metals for cooling and water splitting systems used in industrial, electronics and other applications.
- 17 August 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (8) , 971
Open AccessMultifunctional Properties of Nickel Nanoparticles Produced by Laser Ablation in Liquid
This study explores the multifunctional properties of Ni nanoparticles obtained by laser ablation in liquid, with emphasis on the potential use of these nanoparticles in different applications such as cooling fluids or photoelectrochemical ones. The Ni nanoparticles were synthesized by the laser ablation in liquid technique using an Nd-YAG laser and ultrapure water as liquid. The structural, dimensional, morphologic, and stoichiometric characterizations of the nanoparticles were performed using different techniques such as transmission electron microscopy (TEM), energy dispersive X-ray (EDS) and dynamic light scattering spectroscopy (DLS). Nickel nanoparticles with sizes ranging from 5 to 15 nm in diameter were obtained. The experimental measurements were performed to determine the thermal conductivity and viscosity of the obtained nanofluids, essential parameters in the evaluation of the cooling fluid performances. Loading TiO2 thin films with Ni nanoparticles led to the enhancement of the photoelectrochemical water splitting properties of TiO2 thin films, the Ni nanoparticles acting on the collecting, transferring and separating the photogenerated charges and ultimately improving the overall anodic and cathodic efficiencies. The results obtained can contribute to the development of innovative, multifunctional solutions based on non-precious metals for cooling and water splitting systems used in industrial, electronics and other applications.
- Open Access
- 30 January 2025
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 46 (3) , 1-20
Hybrid Nanofluids-Based Direct Absorption Solar Collector: An Experimental Approach
In the last years, studies have demonstrated the potential of hybrid nanofluids to enhance the performance of direct absorption solar collectors. These working fluids containing noble metals (gold, silver) are known for their local surface plasmon resonance which is the main cause for the increased absorption within the solar spectrum. In the current paper, new direct absorption solar collectors prototypes using water-ethylene glycol solution and 0.1 wt.% silver nanoparticles + reduced graphene oxide dispersed in water-ethylene glycol mixture were designed, built, and tested under outdoor conditions, at two flow rates (1.0 and 1.5 l·min−1) and two inlet temperatures (20 $$^\circ{\rm C}$$ and 30 $$^\circ{\rm C}$$ ), over several days in September 2023, at Brasov, Romania. The results suggested that by using silver nanoparticles + reduced graphene oxide nanofluid, the efficiency is improved related to water-ethylene glycol solution. The maximum relative enhancement in efficiency was 16.72% related to the base fluid. Also, at 1.0 l·min−1, the instantaneous and accumulative energies delivered were about 13.51% and 42.91%, respectively, higher than the water-ethylene glycol solution. Finally, the current results were compared to other research carried out on full-scale direct absorption solar collectors tested in outdoor conditions.- 30 January 2025
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 46 (3) , 1-20
Open AccessHybrid Nanofluids-Based Direct Absorption Solar Collector: An Experimental Approach
In the last years, studies have demonstrated the potential of hybrid nanofluids to enhance the performance of direct absorption solar collectors. These working fluids containing noble metals (gold, silver) are known for their local surface plasmon resonance which is the main cause for the increased absorption within the solar spectrum. In the current paper, new direct absorption solar collectors prototypes using water-ethylene glycol solution and 0.1 wt.% silver nanoparticles + reduced graphene oxide dispersed in water-ethylene glycol mixture were designed, built, and tested under outdoor conditions, at two flow rates (1.0 and 1.5 l·min−1) and two inlet temperatures (20 $$^\circ{\rm C}$$ and 30 $$^\circ{\rm C}$$ ), over several days in September 2023, at Brasov, Romania. The results suggested that by using silver nanoparticles + reduced graphene oxide nanofluid, the efficiency is improved related to water-ethylene glycol solution. The maximum relative enhancement in efficiency was 16.72% related to the base fluid. Also, at 1.0 l·min−1, the instantaneous and accumulative energies delivered were about 13.51% and 42.91%, respectively, higher than the water-ethylene glycol solution. Finally, the current results were compared to other research carried out on full-scale direct absorption solar collectors tested in outdoor conditions. - Open Access
- 11 March 2022
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 23 (6) , 3056
Water-Based Graphene Oxide–Silicon Hybrid Nanofluids—Experimental and Theoretical Approach
In the current paper, a new hybrid nanofluid based on graphene oxide sheets and silicon nanoparticles is proposed for thermal applications. GO sheets and Si nanoparticles with different mixture ratios are dispersed in distilled water. Dynamic viscosity is measured at temperatures within the range 20–50 °C and the values are compared to the results available in the literature. The results indicated that the viscosity increases with increasing the mixture ratio of graphene oxide. A new correlation for the dynamic viscosity based on the experimental findings is proposed. Finally, the criteria for the performance of new hybrid nanofluid for thermal applications are analyzed.
- 11 March 2022
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 23 (6) , 3056
Open AccessWater-Based Graphene Oxide–Silicon Hybrid Nanofluids—Experimental and Theoretical Approach
In the current paper, a new hybrid nanofluid based on graphene oxide sheets and silicon nanoparticles is proposed for thermal applications. GO sheets and Si nanoparticles with different mixture ratios are dispersed in distilled water. Dynamic viscosity is measured at temperatures within the range 20–50 °C and the values are compared to the results available in the literature. The results indicated that the viscosity increases with increasing the mixture ratio of graphene oxide. A new correlation for the dynamic viscosity based on the experimental findings is proposed. Finally, the criteria for the performance of new hybrid nanofluid for thermal applications are analyzed.
- 1 February 2022
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 348
Heat and mass transfer characteristics of the NH3/IL + GNPs solution
- 1 February 2022
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 348
Heat and mass transfer characteristics of the NH3/IL + GNPs solution
- Open Access
- 4 October 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2612
Thermophysical Properties of NH3/IL+ Carbon Nanomaterial Solutions
This study proposes the use of new working fluids, refrigerant/IL+ carbon nanomaterials (CNMs), in absorption systems as an alternative to conventional working fluids. In this regard, the thermophysical properties of ammonia and carbon nanomaterials (graphene and single-wall carbon nanotubes) dispersed into [BMIM]BF4 ionic liquid are theoretically investigated. The thermophysical properties of NH3/IL+ CNMs solutions are computed for weight fractions of NH3 in the range of 0.018–0.404 and temperatures between 293 and 388 K. In addition, two weight fractions of CNMs are considered: 0.005 and 0.01, respectively. Our results indicate that by adding a small amount of nanomaterial to the ionic liquid, the solution’s thermal conductivity is enhanced, while its viscosity and specific heat are reduced. Correlations of the thermal conductivity, viscosity, specific heat, and density of the NH3/IL+ CNMs solutions are proposed.
- 4 October 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2612
Open AccessThermophysical Properties of NH3/IL+ Carbon Nanomaterial Solutions
This study proposes the use of new working fluids, refrigerant/IL+ carbon nanomaterials (CNMs), in absorption systems as an alternative to conventional working fluids. In this regard, the thermophysical properties of ammonia and carbon nanomaterials (graphene and single-wall carbon nanotubes) dispersed into [BMIM]BF4 ionic liquid are theoretically investigated. The thermophysical properties of NH3/IL+ CNMs solutions are computed for weight fractions of NH3 in the range of 0.018–0.404 and temperatures between 293 and 388 K. In addition, two weight fractions of CNMs are considered: 0.005 and 0.01, respectively. Our results indicate that by adding a small amount of nanomaterial to the ionic liquid, the solution’s thermal conductivity is enhanced, while its viscosity and specific heat are reduced. Correlations of the thermal conductivity, viscosity, specific heat, and density of the NH3/IL+ CNMs solutions are proposed.
- 11 November 2020
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 42 (1) , 1-17
Heat Transfer Capability of Ionanofluids for Heat Transfer Applications
- 11 November 2020
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 42 (1) , 1-17
Heat Transfer Capability of Ionanofluids for Heat Transfer Applications
- 11 November 2019
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 140 (5) , 2097-2110
A numerical approach on hybrid nanofluid behavior in laminar duct flow with various cross sections
- 11 November 2019
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 140 (5) , 2097-2110
A numerical approach on hybrid nanofluid behavior in laminar duct flow with various cross sections
- 3 November 2016
- Published by Taylor & Francis in Heat Transfer Engineering
- Vol. 38 (17) , 1496-1505
Experimental Study of Thermo-Physical Properties of Nanofluids Based on γ-Fe2O3Nanoparticles for Heat Transfer Applications
The main goal of the present study was to prepare and also to investigate the effects of both temperature and weight concentration on the thermo-physical properties of γ-Fe2O3/water nanofluids. The γ-Fe2O3 nanoparticles were synthesized by laser pyrolysis technique and characterized using TEM, XRD, and EDX techniques. Thermal conductivity, viscosity and surface tension of γ-Fe2O3/water nanofluids were investigated within the range of the temperature of 20°C to 70°C for various weight concentrations of nanoparticles (0.5, 1.0, 2.0, and 4.0 wt%). The experimental results show that the thermal conductivity ratio is much higher than of thermal conductivity of base fluid. Thus, the relative thermal conductivity was 59% for a concentration of 4.0 wt% and a temperature of 50°C. Also, it has been observed that the influence of weight concentration of nanoparticles on viscosity was lower at temperatures over 55°C. At standard temperature of 25°C and 2.0 wt.% concentration of nanoparticles, the relative dynamic viscosity was 5.61%. Experimental results show that the surface tension increases with increase of weight concentrations and decreases with increase of temperatures. For a temperature of 70°C and 2.0 wt.% concentration of nanoparticles, the relative surface tension was 46%. The experimental results were compared with data available in literature.
- 3 November 2016
- Published by Taylor & Francis in Heat Transfer Engineering
- Vol. 38 (17) , 1496-1505
Experimental Study of Thermo-Physical Properties of Nanofluids Based on γ-Fe2O3Nanoparticles for Heat Transfer Applications
The main goal of the present study was to prepare and also to investigate the effects of both temperature and weight concentration on the thermo-physical properties of γ-Fe2O3/water nanofluids. The γ-Fe2O3 nanoparticles were synthesized by laser pyrolysis technique and characterized using TEM, XRD, and EDX techniques. Thermal conductivity, viscosity and surface tension of γ-Fe2O3/water nanofluids were investigated within the range of the temperature of 20°C to 70°C for various weight concentrations of nanoparticles (0.5, 1.0, 2.0, and 4.0 wt%). The experimental results show that the thermal conductivity ratio is much higher than of thermal conductivity of base fluid. Thus, the relative thermal conductivity was 59% for a concentration of 4.0 wt% and a temperature of 50°C. Also, it has been observed that the influence of weight concentration of nanoparticles on viscosity was lower at temperatures over 55°C. At standard temperature of 25°C and 2.0 wt.% concentration of nanoparticles, the relative dynamic viscosity was 5.61%. Experimental results show that the surface tension increases with increase of weight concentrations and decreases with increase of temperatures. For a temperature of 70°C and 2.0 wt.% concentration of nanoparticles, the relative surface tension was 46%. The experimental results were compared with data available in literature.
- 12 April 2010
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Computational Study of Flow in the Underbody Diffuser for a Simplified Car Model
In this paper, using the facilities offered by the ANSYS CFX, CFD code, the authors investigate numerically the flow around the Ahmed body for the rear slanted upper surface of 35°, fitted with a simple underbody diffuser, without endplates, in order to find the influence of the later one on the main aerodynamic characteristics, drag and lift. Relative motion between body and ground is simulated. The study is performed for different geometrical configurations, length and the angle of the diffuser being the parameters which are varied in ranges which are relevant for hatchback passenger cars. Later, based on a theoretical approach, a coefficient of the equivalent hydraulic resistance of the diffuser is computed, which helps to evaluate the drag due to underbody diffuser.
- 12 April 2010
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Computational Study of Flow in the Underbody Diffuser for a Simplified Car Model
In this paper, using the facilities offered by the ANSYS CFX, CFD code, the authors investigate numerically the flow around the Ahmed body for the rear slanted upper surface of 35°, fitted with a simple underbody diffuser, without endplates, in order to find the influence of the later one on the main aerodynamic characteristics, drag and lift. Relative motion between body and ground is simulated. The study is performed for different geometrical configurations, length and the angle of the diffuser being the parameters which are varied in ranges which are relevant for hatchback passenger cars. Later, based on a theoretical approach, a coefficient of the equivalent hydraulic resistance of the diffuser is computed, which helps to evaluate the drag due to underbody diffuser.