MRMohammad Hasan Ravanji

Mohammad Hasan Ravanji

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammad Hasan Ravanji has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Low Cost Front-End Converter With Maximum Power per Ampere for Rooftop Wind Turbines

    by Mehdi Alemi-Rostami, Ghasem Rezazadeh, Farzad Tahami, Mohammad Hasan Ravanji

    Small Permanent Magnet Synchronous Generators (PMSGs) are widely used in small rooftop wind turbines. In order to inject the electric power generated by the PMSG, into the grid, a back-to-back AC/DC/AC converter is required. In this paper, a low cost with high efficiency converter is proposed for the rectifier stage to obtain the maximum power per ampere of PMSG. This structure based on Discontinuous Conduction Mode Single-Ended Primary Inductor Converter (DCM SEPIC) with a single power electronic switch, proposes a converter which is cost-effective and suitable for the small wind turbine used in residential applications. Furthermore, other advantages of the proposed converter include obtaining maximum power delivered per ampere using a simple control method and reducing the size of converter inductive filter by exploiting the PMSG internal synchronous reactance as part of the filter. Unlike the conventional DCM Boost rectifiers, the proposed converter has a continuous input current, which results in lower PMSG conduction loss. Operation principles and various operating modes of this converter are discussed in detail in this paper and verified by closed-loop simulation and experimental results for a 500W/200V prototype.


  • Improved Generic Model of Variable Speed Wind Turbines for Dynamic Studies

    by Hosein Mirnezhad, Mohammad Hasan Ravanji, Mostafa Parniani

    Fast growth of wind power generation and its contribution in power systems dynamic performance has highlighted the importance of developing generic models for wind turbines. Following the former efforts, an enhanced version of standard generic wind turbine model is proposed in this paper. The enhancements are aimed to make the model applicable for unbalanced Root Mean Square (RMS), short-term frequency stability, and low-voltage ride-through (LVRT) studies. Moreover, fidelity of the overall responses of the model is increased. To achieve these goals, five new blocks are designed and added to the base model and three existing blocks are modified. The new blocks are negative-sequence generator/converter model, inertial controller, LVRT controller, dc-link and the line side converter, and the natural flux models. Responses of the enhanced model are compared with the results of both the base model and a detailed model, and validity of the proposed model is verified by different transient scenarios.


  • Modeling and Control of Variable Speed Wind Turbine Generators for Frequency Regulation

    by Mohammad Hasan Ravanji, Claudio A. Canizares, Mostafa Parniani

    Wind turbine generators (WTG) can participate in system frequency regulation via virtual inertial controllers (VIC). In the presence of frequency disturbances, VIC temporarily regulates the WTG power output forcing it to release/absorb kinetic energy into/from the grid. With increasing penetration of WTGs in power systems, grid operators require these generators to provide frequency regulation services; however, kinetic energy re-lease/absorption can destabilize WTGs. Hence, to address these issues, a new large-perturbation nonlinear WTG model is pro-posed in this paper, based on the WTG internal response that is used to tune typical VICs. Novel worst-case and optimal VIC tuning approaches are also proposed and discussed, based on the developed WTG nonlinear model. Several simulations are presented to test and validate the proposed model and VIC tuning techniques, demonstrating their adequate performance and advantages.


  • Open Access

    Modified virtual inertial controller for prudential participation of DFIG‐based wind turbines in power system frequency regulation

    by Mohammad Hasan Ravanji, Mostafa Parniani

    This study proposes a modified virtual inertial control (MVIC) scheme for doubly‐fed induction generator (DFIG)‐based wind turbines (WTs), which both improves the frequency response of these renewable resources and enhances the power system oscillation damping capabilities. It is shown that the proposed control structure enables the WT to participate prudentially in system frequency regulation, which means the amount of WT kinetic energy released to the grid and its participation in system frequency support is alleviated as its stored energy decreases. The proposed control strategy is introduced conceptually, and its performance is verified analytically. Effects of wind speed variations on the small‐signal stability of DFIG WTs equipped with the proposed MVIC is investigated, as well. For these purposes, the system characteristic equation and its damping ratio, as well as the transfer function between the wind speed and the wind turbine rotor speed are derived and analysed. Eventually, time‐domain simulation results and modal analysis verify the performance of the proposed method and demonstrate its superiority as compared to the conventional virtual inertial controllers.


  • Enhanced Hybrid Modular Multilevel Converter With Improved Reliability and Performance Characteristics

    by Ramin Razani, Mohammad Hasan Ravanji, Mostafa Parniani

    This paper proposes an enhanced hybrid modular multilevel converter (MMC), which utilizes a combination of halfbridge submodules (HBSM) and at least one full-bridge submodule (FBSM). In the proposed structure, FBSMs work with half of the HBSMs nominal voltage in each arm. Due to the presence of FBSMs, HBSMs switching frequency drops significantly, which reduces the converter power loss compared to half-bridge based MMCs. Furthermore, because of redundant FBSMs, (2N+1)-modulation can be employed to generate the output voltage without increasing the circulating current, thus the converter performance is improved notably. Besides, with the redundant FBSMs the converter can continue its operation even if a fault occurs in one of HBSM switches. All the control procedure is accomplished using model predictive control strategy and performance of the proposed converter is verified by several simulation and experimental studies. The obtained results confirm the feasibility of the proposed scheme in reducing the converter loss, improving its performance and fault-tolerant operation.


  • Stability assessment of DFIG-based wind turbines equipped with modified virtual inertial controller under variable wind speed conditions

    by Mohammad Hasan Ravanji, Mostafa Parniani

    This paper investigates the effect of wind speed variations on the small-signal stability of doubly-fed induction generator-based wind turbines equipped with modified virtual inertial controllers (MVIC). MVIC is a control scheme that prudentially emulates the inertial response of the conventional synchronous generators for wind turbines in order to improve their frequency control performance. It also enhances the power oscillation damping capability of the power system. In this paper, it is shown that MVIC is robustly stable against wind speed variations. For this purpose, at first, the equivalent system function between the wind speed and the wind turbine rotor speed is obtained. It is shown, then, that this is a first-order transfer function that its pole is a function of the wind speed, wind turbine rotor speed, and the grid frequency deviations. Nonetheless, for operational values of these quantities, this transfer function is robustly stable. Several simulation results with both non-real and real wind speed data are presented to confirm the theoretical analyses of the paper.


  • A modified indirect model predictive control for modular multilevel converters

    by Ramin Razani, Mohammad Hasan Ravanji, Mostafa Parniani

    Modular multilevel converter (MMC) is among the promising topologies used in high-voltage/power purposes, especially for high-voltage direct-current (HVDC) transmission systems. In this paper, a modified model predictive control (MPC) strategy for an MMC-HVDC system is presented. In the proposed MPC strategy, output current, circulating current and capacitors voltage are controlled separately. In order to reduce the computational burden of the controller, the output current is controlled directly without any optimization. For suppression of the circulating current, capacitors voltage variations are employed to settle the converter arms voltages to their reference values. In addition, the submodules (SMs) capacitor voltages are balanced by using a novel voltage sorting algorithm. In this method, the conventional voltage sorting algorithm is combined with the MPC-based strategy to determine which SMs should be turned on. SM capacitors are sorted based on an expression including their predicted capacitor voltage and the transition between the present and next states. Employing the SM transition states makes it possible to control the converter switching frequency. Performance of the proposed control strategy is verified using MATLAB/Simulink environment. The obtained results confirm the effectiveness of the proposed strategy in confining the converter switching frequency and reducing the circulating current and the controller computational burden.


  • Modeling and Control of Zero-Sequence Circulating Current in Parallel Converters With Space Vector Modulation

    by Mohammad Hasan Ravanji, Nima Amouzegar Ashtiani, Mostafa Parniani, Hossein Mokhtari

    The use of parallel converters is one of the most practical solutions to solve the problem of transmitting bulk power generated in megawatt wind turbines to the grid. In spite of several advantages of paralleling, some considerations must be taken into account. Zero-sequence circulating current flowing between parallel converters is one of these concerns. Characteristic differences and discrepancy of zero-axis duty cycles of the parallel converters are considered as the main origins of this current. This paper investigates another source of this phenomenon in space vector modulation controlled converters. This unnoticed source is the notable third-harmonic voltage generated in the conventional SVM. This claim is confirmed analytically and by simulations. Accordingly, several methods for reduction of this third-harmonic voltage and mitigation of the resultant zero-sequence circulating current are proposed. The performances of these methods are verified analytically and by simulations. Finally, the experimental results are presented to verify the effectiveness of the proposed methods.


  • Design Optimization of a Ladder Secondary Single-Sided Linear Induction Motor for Improved Performance

    by Mohammad Hasan Ravanji, Zahra Nasiri-Gheidari

    In this paper, design and optimization of a ladder-type single-sided linear induction motor (Ladder SLIM) for machine tool applications is investigated. High-speed linear induction machines suffer from the end-effect phenomenon, which can reduce the thrust and result in declined output characteristics. Although it is common to consider this phenomenon in high-speed applications, it is essential to take it into account in the design and analysis of low-speed low-air-gap linear machines. In addition, Ladder SLIMs have significant flux density ripples, and using skewed bars for secondary of the machine is a common solution for it. Therefore, providing required equations, an algorithm for designing a Ladder SLIM considering the end-effect phenomenon based on Duncan model is proposed, and effect of several design parameters on the output characteristics are analyzed. In order to find the optimum design parameters, a multiobjective optimization problem considering efficiency, power factor, and braking force due to the end effect is defined. This problem is optimized with two algorithms, interior point and genetic algorithms, and results are compared. Finally, the validity of the obtained solution is verified using a 2-D and 3-D time-stepping finite-element method.


  • Numerical simulation of high voltage electric pulse comminution of phosphate ore

    by Seyed Mohammad Razavian, Bahram Rezai, Mehdi Irannajad, Mohammad Hasan Ravanji