DCDaniele Chiappe

Daniele Chiappe

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Daniele Chiappe has a total of 93 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Spin-on-diffussants for doping in transition metal dichalcogenide semiconductors

    by Surajit Sutar, Daniele Chiappe, Thomas Nuytten, Thierry Conard, Inge Asselberghs, Dennis Lin, Iuliana Radu

    Spin-on-diffussant (SoD) processing as a doping technique in two-dimensional semiconductors shows a general process compatibility with materials such as MoS2 and WSe2. The characteristic Raman modes in chemical vapor deposition-grown MoS2 are retained after a phosphorus-based SoD processing at temperatures up to 1000 °C; the evolution of the characteristic Raman peaks with SoD processing indicates a reduction in the intrinsic electron concentration. Electrical measurements show a corresponding p-type shift in the MoS2 MOSFET transfer characteristics and indicate possible oxidation of MoS2 by the SoD processing. Both these effects correlate with XPS measurements which confirm the diffusion of phosphorus atoms into MoS2 and increased atomic percentage of Mo oxide after SoD processing. The p-type shifts in the electrical characteristics correspond to a maximum of 2.4 × 1012 cm–2 change in the intrinsic carrier concentration. Repeating the experiment on WSe2 flake devices leads to similar trends: an increased p-type and a decreased n-type conduction indicating p-type doping and a significant increase in the OFF-state leakage current.


  • Analysis of admittance measurements of MOS capacitors on CVD grown bilayer MoS 2

    by Abhinav Gaur, Daniele Chiappe, Dennis Lin, Daire J Cott, Inge Asselberghs, Marc M Heyns, Iuliana Radu

    In this study we present results on the AC admittance response of bilayer MoS 2 films grown using chemical vapor deposition. A new MOS capacitor design for ultra-thin body 2D materials is proposed. We show that along with the density of interface traps ( D it ), a transverse electric field distribution in the semiconductor and parasitic capacitance also cause frequency dispersion in measured capacitance. D it extracted using the conductance method in 40 devices indicates reliable measurements for channel length, L < 10 m. For devices with L > 10 m, an increase in D it is an artifact of access resistance in the semiconductor. Temperature measurements show an increasing defect distribution from cm −2 eV −1 around mid-gap to cm −2 eV −1 close to the conduction band minimum.


  • Effects of buried grain boundaries in multilayer MoS 2

    by Jonathan Ludwig, Ankit Nalin Mehta, Marco Mascaro, Umberto Celano, Daniele Chiappe, Hugo Bender, Wilfried Vandervorst, Kristof Paredis

    Two-dimensional transition metal dichalcogenides have been the focus of intense research for their potential application in novel electronic and optoelectronic devices. However, growth of large area two-dimensional transition metal dichalcogenides invariably leads to the formation of grain boundaries that can significantly degrade electrical transport by forming large electrostatic barriers. It is therefore critical to understand their effect on the electronic properties of two-dimensional semiconductors. Using MoS 2 as an example material, we are able to probe grain boundaries in top and buried layers using conductive atomic force microscopy. We find that the electrical radius of the grain boundary extends approximately 2 nm from the core into the pristine material. The presence of grain boundaries affects electrical conductivity not just within its own layer, but also in the surrounding layers. Therefore, electrical grain size is always smaller than the physical size, and decreases with increasing thickness of the MoS 2 . These results signify that the number of layers in synthetically grown 2D materials must ideally be limited for device applications.


  • Direct and indirect optical transitions in bulk and atomically thin MoS2 studied by photoreflectance and photoacoustic spectroscopy

    by J. Kopaczek, S. J. Zelewski, M. P. Polak, A. Gawlik, D. Chiappe, A. Schulze, M. Caymax, R. Kudrawiec

    Optical transitions in atomically thin MoS2 samples made by sulfidation of a metallic molybdenum layer have been studied by photoreflectance (PR) and photoacoustic (PA) spectroscopy. The obtained spectra are compared with PR and PA spectra of bulk MoS2. It is shown that the absorption edge observed in the PA spectrum shifts to blue when moving from the bulk MoS2 to the atomically thin MoS2 layers, whereas the direct optical transitions at the K point of the Brillouin zone (A and B transitions), which are observed in the PR spectrum, do not shift spectrally in a significant manner. On the other hand, the AH transition, which is related to the direct optical transition at the H point of the Brillouin zone and is typical of bulk MoS2, is not observed for atomically thin MoS2 layers. Moreover, a strong and broad PR resonance related to the band nesting (C transition) is identified in the PR spectra of studied samples. In this case, C and CH transitions are observed for bulk MoS2, while only a C transition is observed for atomically thin MoS2.


  • Impact of MoS 2 layer transfer on electrostatics of MoS 2 /SiO 2 interface

    by V V Afanas'Ev, D Chiappe, M Perucchini, M Houssa, C Huyghebaert, I Radu, A Stesmans

    Using internal photoemission of electrons from few-monolayer thin MoS 2 films into SiO 2 we found that the MoS 2 layer transfer processing perturbs electroneutrality of the interface, leading to an increase of the electron barrier height by ≈0.5–1 eV as compared to the case of the same films synthesized directly on SiO 2 . This effect is associated with the formation of an interface dipole, tentatively ascribed to interaction of H 2 O molecules with the SiO 2 surface resulting in the incorporation of silanol (SiOH) groups. This violation of the interface electroneutrality may account for additional electron scattering in ultrathin transferred films and threshold voltage instabilities. Post-transfer annealing in H 2 S is shown to reduce the transfer-induced interface degradation.


  • Layer-controlled epitaxy of 2D semiconductors: bridging nanoscale phenomena to wafer-scale uniformity

    by Daniele Chiappe, Jonathan Ludwig, Alessandra Leonhardt, Salim El Kazzi, Ankit Nalin Mehta, Thomas Nuytten, Umberto Celano, Surajit Sutar, Geoffrey Pourtois, Matty Caymax, et al.

    The rapid cadence of MOSFET scaling is stimulating the development of new technologies and accelerating the introduction of new semiconducting materials as silicon alternative. In this context, 2D materials with a unique layered structure have attracted tremendous interest in recent years, mainly motivated by their ultra-thin body nature and unique optoelectronic and mechanical properties. The development of scalable synthesis techniques is obviously a fundamental step towards the development of a manufacturable technology. Metal-organic chemical vapor deposition has recently been used for the synthesis of large area TMDs, however, an important milestone still needs to be achieved: the ability to precisely control the number of layers and surface uniformity at the nano-to micro-length scale to obtain an atomically flat, self-passivated surface. In this work, we explore various fundamental aspects involved in the chemical vapor deposition process and we provide important insights on the layer-dependence of epitaxial MoS 2 film’s structural properties. Based on these observations, we propose an original method to achieve a layer-controlled epitaxy of wafer-scale TMDs.


  • (Invited) Layer-Controlled, Wafer-Scale Fabrication of 2D Semiconductor Materials

    by Daniele Chiappe, Valeri Afanasiev, Yoann Tomczak, Surajit Sutar, Alessandra Leonhardt, Jonathan Ludwig, U. Celano, Steven Brems, Ashish Dabral, Geoffrey Pourtois, et al.

    The rapid cadence of MOSFET scaling is stimulating the development of new technologies and accelerating the introduction of new semiconducting materials as silicon alternative. In this context, transition metal dichalcogenides (TMDs) with a unique layered structure have attracted tremendous interest in recent years mainly motivated by the characteristic 2D nature together with distinctive and tunable optoelectronic properties which make them appealing for a wide variety of applications. Their ultra-thin body nature, in particular, is expected to provide superior immunity to short channel effects therefore extending the potential to scale transistors down to the few-nanometer-scale. [1-4] Another key feature of 2D materials is the absence of surface dangling bonds. The latter property has the potential to eliminate lattice mismatch constraints thus paving the way for hybrid integration of TMDs into artificial heterostructures with sharp interfaces and designed band alignment. These ingredients, as recently demonstrated, make TMDs ideal building blocks for the fabrication of tunnel field effect transistors with very steep sub-threshold slope which is mandatory for low voltage device operation. [5] Based on these premises, there are some practical issues that need to tackled in order to enable a TMD-based technology. Given their 2D nature, the electronic properties of TMDs critically depend on the physico-chemical characteristics of the interfaces. Therefore, interface/surface engineering represents a logical route to control the electrical performance of TMD-based devices. Surface quality control is mainly a material growth-related issue. From that standpoint, the development of scalable synthesis techniques is obviously a fundamental step towards the development of a manufacturable technology. However, another important step still needs to be achieved: the ability to precisely control the number of layers and surface uniformity at the nano-to micro-length scale over the entire wafer surface to obtain TMD films with atomically flat, self-passivated surfaces. This challenge is further complicated by the fact that powder vaporization techniques and CVD processes used to grow TMD films do not exhibit a self-limiting character. Because of that, local thickness fluctuations and layer discontinuities are commonly observed in synthetic TMD films. In this work, we will discuss fundamental aspects of film formation and provide a pathway towards layer-controlled, wafer-scale synthesis of TMD films. The high temperatures involved in the synthesis process as well as the use of growth templates require the development of a reliable wafer-scale transfer technology. Such a heterogeneous integration, on the one hand, is useful to overcome the incompatibility of the growth process with processing requirements for the BEOL interconnect structures. On the other hand, it reduces the level of control over the interface between the 2D layer and the dielectric substrate. It is not surprising that electronic transport in transferred TMD films is strongly affected by hydrocarbon residues, non-homogeneities (e.g. uncontrolled strain and contaminated regions), dipole formation, and charge transfer effects. Monitoring environmental effects in ultra-thin TMD films and minimizing the impact of layer transfer on the electrostatic potential distribution across the interface is of utmost importance. A wafer-scale transfer process and related experimental challenges and opportunities will be also presented. B. Radisavljevic, A. Radenovic, J. Brivio, V. Giacometti, and A. Kis, Nature Nanotechnol., 6, 147 (2011). R. Ganatra and Q. Zhang, ACS Nano, 8, 4074 (2014). A. Nourbakhsh, A. Zubair, R. N. Sajjad, A. Tavakkoli K. G., W. Chen, S. Fang, X. Ling, J. Kong, M. S. Dresselhaus, E. Kaxiras, K. K. Berggren, D. Antoniadis, and T. Palacios, Nano Lett., 16 7798 (2016). A. Nourbakhsh, A. Zubair, S. Joglekar, M. Dresselhaus, and T. Palacios, Nanoscale, 18, 6122 (2017). D. Sarkar, X. Xie, W. Liu, W. Cao, J. Kang, Y. Gong, S. Kraemer, P. M. Ajayan and K. Banerjee, Nature, 526, 91 (2015).

  • Modulating the resistivity of MoS2 through low energy phosphorus plasma implantation

    by K. Haynes, R. Murray, Z. Weinrich, X. Zhao, D. Chiappe, S. Sutar, I. Radu, C. Hatem, S. S. Perry, K. S. Jones

    Molybdenum disulfide (MoS2) is a promising potential replacement for Si in future microelectronic devices. Integration in electronic devices will likely involve the growth or transfer of large-area MoS2 films onto substrates and subsequent isolation of devices. In this paper, the effect of ion implantation on the electrical properties of MoS2 is reported. Large-area ∼4 layer MoS2 films were implanted by low energy phosphorus plasma at biases of 100, 200, and 300 V and a dose of 1 × 1014 cm−2. Electrical measurements using patterned Ni/Au contacts show that after implantation, independent of bias, there is greater than a 104 increase in resistivity. TEM and Raman spectroscopy suggest that the film is crystalline prior to and after ion implantation and annealing and that there is no measurable sputtering following implantation. This suggests that the increase in resistivity is likely the result of radiation damage in the MoS2. The thermal stability of the increase in electrical resistivity was assessed by a series of 15 min anneals beginning at 325 °C in a sulfur overpressure and progressing up to 525 °C under an Al2O3 ALD cap. The resistivity increase remained unchanged after annealing. These results suggest that implant isolation could provide a preferable alternative to reactive ion etching or chemical etching for electrical isolation of MoS2.


  • Open Access

    Paramagnetic Intrinsic Defects in Polycrystalline Large-Area 2D MoS2 Films Grown on SiO2 by Mo Sulfurization

    by A. Stesmans, S. Iacovo, D. Chiappe, I. Radu, C. Huyghebaert, S. De Gendt, V. V. Afanas’ev

    A low-temperature electron spin resonance study has been carried out on large-area high-purity polycrystalline two-dimensional few monolayer (ML) 2H MoS2 films synthesized by sulfurization of Mo layers, with intent to atomically assess mobility-degrading detrimental point defects. This reveals the presence of a distinct previously unreported anisotropic defect of axial symmetry about the c-axis characterized by g // = 2.00145 and g ⊥ = 2.0027, with corresponding density (spin S = ½) ~3 × 1012 cm−2 for a 4 ML thick film. Inverse correlation of the defect density with grain size points to a domain boundary associated defect, inherently incorporated during sample growth. Based on the analysis of ESR signal features in combination with literature data, the signal is tentatively ascribed to the a (di)sulfur antisite defect (S or S2 substituting for a Mo atom). Beset by these defects, the grain boundaries thus emerge as an intolerable threat for the carrier mobility and layer functionality.


  • Transport properties of chemically synthesized MoS2 – Dielectric effects and defects scattering

    by Massimo Mongillo, Daniele Chiappe, Goutham Arutchelvan, Inge Asselberghs, Marta Perucchini, Mauricio Manfrini, Dennis Lin, Cedric Huyghebaert, Iuliana Radu

    We report on the electrical characterization of synthetic, large-area MoS2 layers obtained by the sulfurization technique. The effects of dielectric encapsulation and localized defect states on the intrinsic transport properties are explored with the aid of temperature-dependent measurements. We study the effect of dielectric environment by transferring as-grown MoS2 films into different dielectrics such as SiO2, Al2O3, HfO2, and ZrO2 with increasing dielectric permittivity. Electrical data are collected on a statistically-relevant device ensemble and allow to assess device performances on a large scale assembly. Our devices show relative in-sensitiveness of mobility with respect to dielectric encapsulation. We conclude that the device behavior is strongly affected by several scattering mechanisms of different origin that can completely mask any effect related to dielectric mismatch. At low temperatures, conductivity of the devices is thermally activated, a clear footprint of the existence of a mobility edge separating extended states in the conduction band from impurity states in the band-gap.