Ludmila Kučerová
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ludmila Kučerová has a total of 140 co-authors. Here are the top co-authors by number of shared publications:
- Hana Jirková
Research and Testing Institute Plzen
27 shared publications - Štěpán Jeníček
Regional Technological Institute, University of West Bohemia, Univerzitní 8, 301 00 Pilsen, Czech Republic
22 shared publications - Karolína Burdová
Regional Technological Institute, University of West Bohemia, Univerzitni 8, 30614, Plzen, Czech Republic
13 shared publications - Bohuslav Mašek
Faculty of Electrical Engineering, University of West Bohemia, Plzen, Czech Republic
12 shared publications - Ivana Zetková
Faculty of Mechanical Engineering University of West Bohemia Univerzitní 8 306 14 Pilsen Czech Republic
12 shared publications Martin Bystrianský
University of West Bohemia in Pilsen
6 shared publications
Latest Publications
- Open Access
- 21 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 26 (3) , 61-70
Industrial Potential of Additively Manufactured H13 Steel Components: A Service Life Study
This article focuses on evaluating the service life of components made from H13 tool steel manufactured using additive manufacturing, specifically 3D printing. This was done by comparing them with components produced by conventional manufacturing methods. H13 tool steel is widely used due to its high mechanical strength and resistance to thermal cycling, properties which are particularly important in high-pressure die casting (HPDC) applications. In such processes, components are regularly subjected to significant mechanical and thermal stresses. The article provides a comprehensive comparison of dimensional stability, porosity, surface roughness, hardness, and operational wear in conventionally and additively manufactured H13 components. Additional measurements of surface roughness were conducted to provide further insight into the material’s surface condition and the overall reliability of the additively manufactured components. The results provide insight into the advantages and limitations of additively manufactured H13 components and support their potential industrial application in high-pressure die casting.
- 21 September 2026
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 26 (3) , 61-70
Open AccessIndustrial Potential of Additively Manufactured H13 Steel Components: A Service Life Study
This article focuses on evaluating the service life of components made from H13 tool steel manufactured using additive manufacturing, specifically 3D printing. This was done by comparing them with components produced by conventional manufacturing methods. H13 tool steel is widely used due to its high mechanical strength and resistance to thermal cycling, properties which are particularly important in high-pressure die casting (HPDC) applications. In such processes, components are regularly subjected to significant mechanical and thermal stresses. The article provides a comprehensive comparison of dimensional stability, porosity, surface roughness, hardness, and operational wear in conventionally and additively manufactured H13 components. Additional measurements of surface roughness were conducted to provide further insight into the material’s surface condition and the overall reliability of the additively manufactured components. The results provide insight into the advantages and limitations of additively manufactured H13 components and support their potential industrial application in high-pressure die casting.
- Open Access
From heat-treatment maps to repairable tooling of LPBF-produced M789 maraging stainless steel
- Open Access
- 27 August 2026
- Published by Elsevier in Intermetallics
- Vol. 198
Phase constitution, microstructure and load-dependent dry-sliding behaviour of a multiphase AlFeNiSiTi aluminide–silicide alloy
- 27 August 2026
- Published by Elsevier in Intermetallics
- Vol. 198
Open AccessPhase constitution, microstructure and load-dependent dry-sliding behaviour of a multiphase AlFeNiSiTi aluminide–silicide alloy
- Open Access
- 24 August 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 10773-10786
Post-processing of laser powder bed fusion-produced H11 tool steel: transferability of conventional heat treatment and long-term thermal stability
- 24 August 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (10) , 10773-10786
Open AccessPost-processing of laser powder bed fusion-produced H11 tool steel: transferability of conventional heat treatment and long-term thermal stability
- Open Access
- 20 February 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 957
High strength without quenching: Tempering effects in additively manufactured Dievar tool steel
- 20 February 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 957
Open AccessHigh strength without quenching: Tempering effects in additively manufactured Dievar tool steel
- 22 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 54-62
A Study of the Mechanical Properties of Conventional and Additive Mould Parts for Die Casting of Aluminum Alloys
The article focuses on the mechanical properties of mould parts created using 3D printing technology, for use in the production of castings by High-Pressure Die Casting (HPDC). The mould shapes produced by 3D printing technology bring innovative approaches to optimising production processes. H13 tool steel is widely used for its excellent mechanical properties and resistance to thermal stress. The study focuses on the comparison of the mechanical properties of mould parts produced by traditional methods and 3D printing, with emphasis on their strength, hardness and wear resistance under repeated working cycles. The experimental part includes roughness measurements and tests of mechanical properties, which provide important data on the ability of these components to withstand high mechanical loads and temperature fluctuations during the HPDC process. The results of the study show the advantages and limitations of 3D printing compared to traditional manufacturing processes and give insight into the use of additive technologies in industrial manufacturing. Specifically, the study identified clear quantitative differences in mechanical properties: the 3D printed mould parts had comparable ultimate tensile strength and yield strength to conventionally manufactured parts, but significantly lower ductility (below 1% compared to about 20% in traditional parts) due to higher porosity (0.25–0.30% compared to 0.03–0.04%). Additive mould parts exhibited higher hardness (approximately 510 HV) compared to conventional parts (approximately 450 HV). Surface roughness of the 3D printed parts was more variable, highlighting the need for optimising printing parameters. Thus, additive technology offers benefits in stable hardness and comparable strength, albeit at the expense of reduced ductility and increased variability in surface quality. The research also includes an analysis of the effect of repetitive loading on the mechanical properties of the mould parts made of H13, which provides valuable information for improving their durability and reliability in practice. This research contributes to the development of 3D printing technologies in the field of HPDC and offers new opportunities for improving the efficiency and quality of manufacturing processes in industrial applications.
- 22 December 2025
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- p. 54-62
A Study of the Mechanical Properties of Conventional and Additive Mould Parts for Die Casting of Aluminum Alloys
The article focuses on the mechanical properties of mould parts created using 3D printing technology, for use in the production of castings by High-Pressure Die Casting (HPDC). The mould shapes produced by 3D printing technology bring innovative approaches to optimising production processes. H13 tool steel is widely used for its excellent mechanical properties and resistance to thermal stress. The study focuses on the comparison of the mechanical properties of mould parts produced by traditional methods and 3D printing, with emphasis on their strength, hardness and wear resistance under repeated working cycles. The experimental part includes roughness measurements and tests of mechanical properties, which provide important data on the ability of these components to withstand high mechanical loads and temperature fluctuations during the HPDC process. The results of the study show the advantages and limitations of 3D printing compared to traditional manufacturing processes and give insight into the use of additive technologies in industrial manufacturing. Specifically, the study identified clear quantitative differences in mechanical properties: the 3D printed mould parts had comparable ultimate tensile strength and yield strength to conventionally manufactured parts, but significantly lower ductility (below 1% compared to about 20% in traditional parts) due to higher porosity (0.25–0.30% compared to 0.03–0.04%). Additive mould parts exhibited higher hardness (approximately 510 HV) compared to conventional parts (approximately 450 HV). Surface roughness of the 3D printed parts was more variable, highlighting the need for optimising printing parameters. Thus, additive technology offers benefits in stable hardness and comparable strength, albeit at the expense of reduced ductility and increased variability in surface quality. The research also includes an analysis of the effect of repetitive loading on the mechanical properties of the mould parts made of H13, which provides valuable information for improving their durability and reliability in practice. This research contributes to the development of 3D printing technologies in the field of HPDC and offers new opportunities for improving the efficiency and quality of manufacturing processes in industrial applications.
- Open Access
Press Hardening of High-Carbon Low-Density Steels
In this study, sheets of experimental high-carbon low-density steels (LDSs) with a thickness of 1.7 mm were processed in a combined tool designed for press-hardening. Press hardening, also known as hot stamping or hot press forming, is a manufacturing process used to create car body parts with exceptional mechanical properties and safety standards. These components often require tailored properties, meaning different mechanical characteristics in various parts of the component. LDSs have a lower specific density than conventional steels, so their use would be particularly suitable in automotive applications. Combined tools achieve distinct mechanical properties within a single part through thermomechanical processing. Simultaneous forming and heat treatment create tailored zones of high strength and ductility within the sheet metal. The hardened zone provides crashworthiness, while the more ductile zone absorbs kinetic energy and converts it into deformation energy. Hot stamping enables forming complex geometries from high-strength sheets with limited cold formability, a capability that can also be exploited for the aluminium-alloyed LDS under investigation in this work. Three different high-carbon LDSs with differences in chemical composition were subjected to this experiment, and the hardness, microstructure, and mechanical properties of the two areas of each sheet were evaluated. The aim is to determine their suitability for processing by press hardening and to try to achieve tailored properties (i.e., differences in ductility and strength across one part) as in a typical representative of 22MnB5 boron steel, where a strength limit of 1500 MPa at 5% ductility is achieved in the cooled part and 600 MPa at 15% in the heated part. Tailored properties were also achieved in the investigated LDS, but with only relatively small differences between the two tool areas. The omega profiles were produced by press hardening without visible defects, and it was possible to process the steels without any difficulties.
Open AccessPress Hardening of High-Carbon Low-Density Steels
In this study, sheets of experimental high-carbon low-density steels (LDSs) with a thickness of 1.7 mm were processed in a combined tool designed for press-hardening. Press hardening, also known as hot stamping or hot press forming, is a manufacturing process used to create car body parts with exceptional mechanical properties and safety standards. These components often require tailored properties, meaning different mechanical characteristics in various parts of the component. LDSs have a lower specific density than conventional steels, so their use would be particularly suitable in automotive applications. Combined tools achieve distinct mechanical properties within a single part through thermomechanical processing. Simultaneous forming and heat treatment create tailored zones of high strength and ductility within the sheet metal. The hardened zone provides crashworthiness, while the more ductile zone absorbs kinetic energy and converts it into deformation energy. Hot stamping enables forming complex geometries from high-strength sheets with limited cold formability, a capability that can also be exploited for the aluminium-alloyed LDS under investigation in this work. Three different high-carbon LDSs with differences in chemical composition were subjected to this experiment, and the hardness, microstructure, and mechanical properties of the two areas of each sheet were evaluated. The aim is to determine their suitability for processing by press hardening and to try to achieve tailored properties (i.e., differences in ductility and strength across one part) as in a typical representative of 22MnB5 boron steel, where a strength limit of 1500 MPa at 5% ductility is achieved in the cooled part and 600 MPa at 15% in the heated part. Tailored properties were also achieved in the investigated LDS, but with only relatively small differences between the two tool areas. The omega profiles were produced by press hardening without visible defects, and it was possible to process the steels without any difficulties.
- 10 November 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1166, 39-43
Comparing the Mechanical Properties of Secure Ballistic Steels after Heat Treatment by the Q-P Process
Ballistic steels are used for the basic ballistic protection of armoured vehicles against the compressive energy of exploding munitions and the impact energy of projectiles fired from small arms. Steels with hardness up to 500 HBW are used to protect the chassis of armoured vehicles. Steels with a hardness greater than 500 HBW are used to protect the cabs and turrets of armoured vehicles. Ballistic steels belong to the class of low alloy high strength steels where a good combination of high strength and toughness is required. Higher strength is achieved in the final production process which involves heat treatment by quenching and tempering. This treatment creates a martensitic structure. Another heat treatment option is the Q-P (quenching and partitioning) process, where higher material strengths can be achieved in some steels while maintaining ductility. This paper focuses on a comparison of the microstructure as observed using a light microscope of the ballistic steel Secure after heat treatment by the manufacturer and after heat treatment by the Q-P process. It was found that the Q-P process produces a finer grained structure and a change in mechanical properties due to the stabilised austenite and strained martensite in the microstructure of the ballistic steel.
- 10 November 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1166, 39-43
Comparing the Mechanical Properties of Secure Ballistic Steels after Heat Treatment by the Q-P Process
Ballistic steels are used for the basic ballistic protection of armoured vehicles against the compressive energy of exploding munitions and the impact energy of projectiles fired from small arms. Steels with hardness up to 500 HBW are used to protect the chassis of armoured vehicles. Steels with a hardness greater than 500 HBW are used to protect the cabs and turrets of armoured vehicles. Ballistic steels belong to the class of low alloy high strength steels where a good combination of high strength and toughness is required. Higher strength is achieved in the final production process which involves heat treatment by quenching and tempering. This treatment creates a martensitic structure. Another heat treatment option is the Q-P (quenching and partitioning) process, where higher material strengths can be achieved in some steels while maintaining ductility. This paper focuses on a comparison of the microstructure as observed using a light microscope of the ballistic steel Secure after heat treatment by the manufacturer and after heat treatment by the Q-P process. It was found that the Q-P process produces a finer grained structure and a change in mechanical properties due to the stabilised austenite and strained martensite in the microstructure of the ballistic steel.
- Open Access
- 22 September 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 946
Additive manufacturing and heat treatment of Dievar tool steel
- 22 September 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 946
Open AccessAdditive manufacturing and heat treatment of Dievar tool steel
- 15 July 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 155
Effect of lattice defects on hydrogen storage properties of HfNbTiZr medium entropy alloy
- 15 July 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 155
Effect of lattice defects on hydrogen storage properties of HfNbTiZr medium entropy alloy