JRJoakim Riikonen

Joakim Riikonen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Joakim Riikonen has a total of 223 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Toward field‑deployable sediment porewater extraction: A comparative study for environmental trace metal monitoring

    by Joshua Izegaegbe, Sidra Iftekhar, Joakim Riikonen, Tommi Tiihonen, Jarkko Akkanen, Vesa-Pekka Lehto

    Sediment porewater is a key medium for controlling contaminant mobility and bioavailability in aquatic systems. Yet, methodologies to extract porewater from sediment samples differ substantially in their efficiency, reliability, and suitability for field deployment. The present study compared four porewater extraction techniques: Laboratory centrifugation, portable centrifugation, Rhizon samplers, and a novel AeroPress-based extraction device, utilizing silty and sandy sediments from two boreal lakes. Extraction efficiency, sample contamination risks, and operational feasibility for field use were evaluated. Laboratory and portable centrifugation produced the highest porewater recoveries, generally exceeding 25%–50% extraction efficiency, whereas AeroPress and Rhizon samplers yielded lower recoveries. The metal concentrations in the extracted pore water samples varied between the extraction methods and sediment types, with Rhizon samplers and AeroPress yielding higher concentrations of specific trace metals in some cases due to leaching of the metals from the components of the extraction devices, causing sample contamination. No consistent relationship was observed between extraction efficiency and metal concentrations in the extracted water samples. However, Pb showed a strong positive correlation with extraction efficiency, suggesting preferential recovery with higher-volume methods. Portable centrifugation provided the most practical balance between efficiency and field applicability based on both the volume of porewater that can be extracted and ease of use, while AeroPress offers a promising low-energy alternative in power-limited settings. These findings highlight that the porewater extraction method, the filter material, and sediment type affect the metal concentrations in the extracted porewater samples and should be carefully considered when applied for environmental monitoring.

  • Open Access

    Real-time spatial mapping of metal concentrations in environmental waters for ecological monitoring using a portable XRF device

    by Mikhail Sandzhiev, Sidra Iftekhar, Joshua Izegaegbe, Mate Udvarhelyi, Joakim Riikonen, Vesa-Pekka Lehto

    The monitoring of metal pollution in environmental waters is crucial for the protection of ecosystems, human health and agricultural activities. Traditional laboratory metal analyses provide accurate concentration values, but the results are typically delivered as standalone numbers that lack immediate spatial context. Without additional processing, they do not directly reveal patterns, hotspots, or geographic relationships. The key challenge is therefore not measurement itself but transforming analytical data into spatially meaningful information that supports rapid interpretation and decision-making. The present study introduces a new approach to real-time water quality monitoring using portable X-ray fluorescence (p-XRF) technology coupled with geographic information systems (GIS). Using a custom Python script, p-XRF data measured on-site is processed and formatted into a GIS-compatible format, facilitating spatial visualization of metal concentrations in QGIS. Key aspects include robust data collection, spatial visualization, and validation processes to ensure accuracy and efficiency. These features provide quick and efficient insights into metal contamination trends and allow smart sampling and proactive decision-making.

  • On-site elemental analysis of environmental waters using portable XRF

    by Joakim Riikonen, Tommi Tiihonen, Arezoo Rahmani, Tuomo Nissinen, Ondrej Haluska, Konstantin Tamarov, Toni Pennanen, Petri Turhanen, Jouko Vepsäläinen, Vesa-Pekka Lehto

    Rapid on-site detection of metals in water is essential for timely environmental assessment, especially in remote areas or time-critical situations. In this work, we present a portable measurement system that combines preconcentration filters with a portable X-ray fluorescence (pXRF) analyzer. Filters for Mn, Co, Ni, Cu, Zn, Pb, and U were fabricated using nanoporous silicon or silicon carbide with polymeric binders, while arsenic was captured using ferrihydrite-based filters. Water samples were collected from lakes, boreholes, and wells, and measured on-site. Detection limits as low as 12 µg/L for metals and 1.3 µg/L for arsenic were achieved, depending on sample volume. Results were validated against laboratory ICP-MS analysis. The lightweight, battery-operated setup enables field deployment with total measurement times as short as 15 minutes, offering a practical tool for preliminary screening and environmental monitoring in challenging conditions.

  • Open Access

    Bisphosphonate functionalized biogenic nanostructured silicon carbide for uranium and scandium recovery

    by Sidra Iftekhar, Ondřej Haluska, Arezoo Rahmani, Rinez Thapa, Joakim Riikonen, Reijo Lappalainen, Jouko Vepsäläinen, Vesa-Pekka Lehto


  • Open Access

    Removing siloxanes and hydrogen sulfide from landfill gases with biochar and activated carbon filters

    by Mikko Selenius, Joonas Ruokolainen, Joakim Riikonen, Jimi Rantanen, Simo Näkki, Vesa-Pekka Lehto, Marko Hyttinen


  • Open Access

    Production of graphitic carbons from plant-based SiC/C nanocomposites for Li-ion batteries

    by Ondřej Haluska, Sara-Maaria Meščeriakovė, Kirill Murashko, Arūnas Meščeriakovas, Nathiya Kalidas, Jimi Rantanen, Lizhi Liu, Ayobami Salami, Reijo Lappalainen, Anna Lähde, et al.


  • Open Access

    Real-Time On-Site Multielement Analysis of Environmental Waters with a Portable X-ray Fluorescence (pXRF) System

    by Tommi E. Tiihonen, Tuomo J. Nissinen, Petri A. Turhanen, Jouko J. Vepsäläinen, Joakim Riikonen, Vesa-Pekka Lehto

    Strict regulations are in place to control the effluents of mining sites and other industries. Heavy metal contamination of aquatic systems caused by leakages is difficult to mitigate as it takes time to detect and localize the leak. Dynamic sampling would drastically reduce the time to locate leakages and allow faster actions to reduce the impact on the environment. The present study introduces a novel portable multielement water analysis system to simultaneously measure Mn, Ni, Cu, Zn, Pb, and U in water samples from natural sources within 15 min from the sampling. The metals are preconcentrated from a 10 mL water sample into a nanoporous filter based on bisphosphonate-modified thermally carbonized porous silicon. The metals can be conveniently analyzed from the filter with a portable XRF analyzer in field conditions. The system was empirically calibrated for a lake water matrix with neutral pH and low alkaline metal concentration. A strong correlation between the XRF intensities and the ICP-MS results was obtained in a concentration range from 50 to 10 000 μg/L. With a DPO-2000C XRF analyzer, the detection limits were 103, 86, 92, 35, 44, and 43 μg/L for Mn, Ni, Cu, Zn, Pb, and U, respectively. The corresponding values with X-MET8000 Expert Geo were 137, 46, 62, 38, 29, and 54. The system was successfully validated with simulated multielement lake water samples and piloted in field conditions. The system provides an efficient way to monitor metals in environmental waters in cases where quick on-site results are needed.


  • Open Access

    Plant-based nanostructured silicon carbide modified with bisphosphonates for metal adsorption

    by Ondřej Haluska, Arezoo Rahmani, Ayobami Salami, Petri Turhanen, Jouko Vepsäläinen, Reijo Lappalainen, Vesa-Pekka Lehto, Joakim Riikonen


  • Open Access

    Biogenic nanoporous silicon carrier improves the efficacy of buparvaquone against resistant visceral leishmaniasis

    by Rinez Thapa, Subhasish Mondal, Joakim Riikonen, Jimi Rantanen, Simo Näkki, Tuomo Nissinen, Ale Närvänen, Vesa-Pekka Lehto

    Visceral leishmaniasis is a vector-borne protozoan infection that is fatal if untreated. There is no vaccination against the disease, and the current chemotherapeutic agents are ineffective due to increased resistance and severe side effects. Buparvaquone is a potential drug against the leishmaniases, but it is highly hydrophobic resulting in poor bioavailability and low therapeutic efficacy. Herein, we loaded the drug into silicon nanoparticles produced from barley husk, which is an agricultural residue and widely available. The buparvaquone-loaded nanoparticles were several times more selective to kill the intracellular parasites being non-toxic to macrophages compared to the pure buparvaquone and other conventionally used anti-leishmanial agents. Furthermore, the in vivo results revealed that the intraperitoneally injected buparvaquone-loaded nanoparticles suppressed the parasite burden close to 100%. By contrast, pure buparvaquone suppressed the burden only by 50% with corresponding doses. As the conclusion, the biogenic silicon nanoparticles are promising carriers to significantly improve the therapeutic efficacy and selectivity of buparvaquone against resistant visceral leishmaniasis opening a new avenue for low-cost treatment against this neglected tropical disease threatening especially the poor people in developing nations.


  • Injection Metal-Assisted Catalytic Etching (MACE) of Si Powder: Discovery of Low-Load MACE and Pore Distribution Tunability Using Ag, Au, Pd, Pt and Cu Catalysts

    by Kurt W Kolasinski, Konstantin Tamarov, Joseph D. Swanson, Bret A. Unger, Alexis T. Ernst, Mark Aindow, Riku Kiviluoto, Vesa-Pekka Lehto, Joakim Riikonen

    Injection of H2O2 to control both the rate and extent of etching allowed us to discover a new regime of MACE with extremely small quantities of deposited metal as a catalyst: low-load MACE (LL-MACE).1 The structure of particles subjected to LL-MACE is completely different compared to conventional MACE. Si nanowires and mesoporous micro- or nano-particles are produced with high yield, low cost and controlled properties suitable for applications in e.g. lithium-ion batteries, drug delivery, as well as biomedical imaging and contrast enhancement. Different metal catalysts behave in distinct manners than can be traced to differences in nucleation and reaction kinetics.2 Not only Ag, Au, Pd and Pt but also inexpensive Cu can be used to perform LL-MACE. Previously, controlled reactant injection and acetic acid were used to transform stain etching into the improved process known as regenerative electroless etching (ReEtching).3 Here injection and acetic acid are exploited to enhance MACE and extend it to the low-load regime. Ag, Au, Pd, Pt and Cu can be galvanically deposited onto Si powder out of solutions of HF(aq). Nucleation of deposited metal nanoparticles is made more uniform by dispersing the Si powder in acetic acid and injecting the dissolved metal ions at a controlled rate. The use of a syringe pump to deliver not only metal ions during deposition but also the oxidant (H2O2) during MACE is essential for increased product uniformity and yield. Temperatures of ~0–50 °C and grades of Si (i.e. electronics grade Si with various doping levels or metallurgical grade Si) produced significantly different pore size distributions. Doping levels and the associated changes in band bending and space charge layer width4 are linked to changes in the pore size distribution. As shown in Fig. 1(A), high loading of Ag resulted in deposition of dendrites and Ag particles. These broke into ~50–100 nm Ag nanoparticles that etched in a correlated fashion to generate parallel etch track pores. The uniform size distribution of the Ag nanoparticles was generated dynamically during etching. This conventional high-load MACE (HL-MACE) did not produce Si nanowires (Si NWs) directly. However, etch track pore walls were cleaved readily by ultrasonic agitation to form Si NWs. Etching far removed from the metal nanoparticles (remote etching) also occurred for highly doped Si. As shown in Fig. 1(B), reducing the loading of Ag by a factor of 100 to 1000 compared to HL-MACE created 10–30 nm nanoparticles that etched in an uncorrelated fashion and generated randomly directed etch track pores. Significant etching far removed from the Ag catalyst also occurred. The combination of localized and remote etching resulted in a bimodal distribution of mesoporosity peaking at ~4 nm from remote etching and 10–30 nm from localized etching. The bimodal distribution was confirmed by the BJH method of nitrogen adsorption porosimetry. The pore size distribution could be controlled by changing the process temperature, the grade of Si and the metal composition. Whereas Ag, Au, Pd and Pt performed well in both the HL and LL limits, Cu generated porosification only in the LL limit. Funded by grants #314552 and #314412 from Academy of Finland and the National Science Foundation award #1825331. The microscopy studies were performed using the facilities in the UConn/Thermo Fisher Scientific Center for Advanced Microscopy and Materials Analysis (CAMMA). 1 K. Tamarov, J. D. Swanson, B. A. Unger, K. W. Kolasinski, A. T. Ernst, M. Aindow, V.-P. Lehto, and J. Riikonen, ACS Appl. Mater. Interfaces 12, 4787 (2020). 2 K. W. Kolasinski, W. B. Barclay, Y. Sun, and M. Aindow, Electrochim. Acta 158, 219 (2015). 3 K. W. Kolasinski, N. J. Gimbar, H. Yu, M. Aindow, E. Mäkilä, and J. Salonen, Angew. Chem., Int. Ed. Engl. 56, 624 (2017). 4 E. Torralba, S. Le Gall, R. Lachaume, V. Magnin, J. Harari, M. Halbwax, J.-P. Vilcot, C. Cachet-Vivier, and S. Bastide, ACS Appl. Mater. Interfaces 8, 31375 (2016). Figure 1