Horacio Javier Aguerre
Research Subjects
Horacio Javier Aguerre has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Norberto Marcelo Nigro
Centro Internacional de Métodos Computacionales en Ingeniería (CIMEC), INTEC-CONICET-UNL, Güemes 3450, 3000 Santa Fe, Argentina
6 shared publications - Juan Marcelo Gimenez
Centre Internacional de Mètodes Numèrics en Enginyeria (CIMNE), Barcelona, Spain
5 shared publications Santiago Márquez Damián
5 shared publicationsNorberto M. Nigro
4 shared publications- Alexis L. Dallinger
Centro de Investigacion de Metodos Computacionales (CIMEC), CONICET-UNL. Santa Fe, Argentina
1 shared publication - Axel E. Larreteguy
Instituto de Tecnología, Universidad Argentina de la Empresa (UADE) 1 , Lima 775, C1073AAO Ciudad Autónoma de Buenos Aires, Argentina
1 shared publication
Latest Publications
- Open Access
- 26 October 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (44) , 68496-68517
Assessing Linear FAME-Property Relationships in Heterogeneous Biodiesel Databases: A Sequential Cross-Validated Subset-Selection Approach
Linear correlations based on fatty acid methyl ester (FAME) composition provide a transparent approach for estimating biodiesel properties, although their applicability to heterogeneous literature databases depends on the existence of a consistent composition-property structure. This work assesses linear relationships for density, kinematic viscosity, flash point, and lower and higher heating values using the normalized shares of palmitic, stearic, oleic, linoleic, and linolenic esters. A sequential nested leave-one-out procedure selects, at each stage, the observation whose exclusion maximizes the cross-validated performance of the remaining subset. The complete procedure is also applied to response-permuted, or Y-randomized, surrogate databases. The archived operating point is the first stage at which the fitted real trajectory reaches Rfit2 ≥ 0.60, while the real-versus-permuted differential Δ(k) compares the fitted linear compatibility of the actual FAME-property pairing with the mean fitted linear compatibility obtained after response randomization. Because sustained removal also raises the surrogate trajectories, the fitted R2 alone is not interpreted as evidence of a composition–property relation; the comparison relies on Δ(k). Exploratory data analysis first characterizes the original databases through target-property distributions, descriptive statistics, and literature-source and feedstock representation. This baseline is then extended by comparing the original and retained databases in terms of literature-source and dominant-FAME retention, target-property distributions, principal-component coverage, and Spearman rank-correlation structure, showing that the retained subsets largely preserve the main compositional characteristics of the original databases. Cook’s distance and Williams plots provide independent influence flags for a substantial, but incomplete, fraction of the selected observations, including response-inconsistent and high-leverage cases. Selected observations are interpreted as operationally incompatible with the five-FAME linear description at their respective selection stages; possible causes include influence, omitted descriptors, or nonlinear behavior. The combined statistical, representational, and physical evidence supports conditional linear correlations for kinematic viscosity, flash point, and higher heating value, in decreasing order of feasibility. In contrast, the selected density and lower-heating-value databases do not provide sufficient evidence for reliable linear correlations using the five-FAME representation. Semisynthetic manufactured databases show above-blind enrichment of planted response mismatches and generally reproducible coefficient recovery, with property-specific exceptions. The proposed framework therefore provides a systematic means of identifying and characterizing linear-compatible regimes within heterogeneous biodiesel property databases.
- 26 October 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (44) , 68496-68517
Open AccessAssessing Linear FAME-Property Relationships in Heterogeneous Biodiesel Databases: A Sequential Cross-Validated Subset-Selection Approach
Linear correlations based on fatty acid methyl ester (FAME) composition provide a transparent approach for estimating biodiesel properties, although their applicability to heterogeneous literature databases depends on the existence of a consistent composition-property structure. This work assesses linear relationships for density, kinematic viscosity, flash point, and lower and higher heating values using the normalized shares of palmitic, stearic, oleic, linoleic, and linolenic esters. A sequential nested leave-one-out procedure selects, at each stage, the observation whose exclusion maximizes the cross-validated performance of the remaining subset. The complete procedure is also applied to response-permuted, or Y-randomized, surrogate databases. The archived operating point is the first stage at which the fitted real trajectory reaches Rfit2 ≥ 0.60, while the real-versus-permuted differential Δ(k) compares the fitted linear compatibility of the actual FAME-property pairing with the mean fitted linear compatibility obtained after response randomization. Because sustained removal also raises the surrogate trajectories, the fitted R2 alone is not interpreted as evidence of a composition–property relation; the comparison relies on Δ(k). Exploratory data analysis first characterizes the original databases through target-property distributions, descriptive statistics, and literature-source and feedstock representation. This baseline is then extended by comparing the original and retained databases in terms of literature-source and dominant-FAME retention, target-property distributions, principal-component coverage, and Spearman rank-correlation structure, showing that the retained subsets largely preserve the main compositional characteristics of the original databases. Cook’s distance and Williams plots provide independent influence flags for a substantial, but incomplete, fraction of the selected observations, including response-inconsistent and high-leverage cases. Selected observations are interpreted as operationally incompatible with the five-FAME linear description at their respective selection stages; possible causes include influence, omitted descriptors, or nonlinear behavior. The combined statistical, representational, and physical evidence supports conditional linear correlations for kinematic viscosity, flash point, and higher heating value, in decreasing order of feasibility. In contrast, the selected density and lower-heating-value databases do not provide sufficient evidence for reliable linear correlations using the five-FAME representation. Semisynthetic manufactured databases show above-blind enrichment of planted response mismatches and generally reproducible coefficient recovery, with property-specific exceptions. The proposed framework therefore provides a systematic means of identifying and characterizing linear-compatible regimes within heterogeneous biodiesel property databases.
- Open Access
- 13 December 2025
- Published by Asociación Argentina De Mecánica Computacional in Resúmenes de Mecánica Computacional
- Vol. 2 (2) , 27
Estudio CFD de Paneles Evaporativos de Celulosa para Evaluar Pérdida de Carga y Transferencia de Calor
Los paneles evaporativos de celulosa constituyen una solución de bajo consumo energético para la climatización de grandes espacios industriales y agrícolas, aprovechando el enfriamiento por evaporación del agua. Sin embargo, su caracterización técnica detallada en condiciones reales de operación es limitada. En este trabajo se presenta un estudio preliminar por CFD de un panel fabricado por DollTec, mediante simulaciones full 3D en OpenFOAM. Se modeló una sección representativa del panel y se llevó a cabo un análisis de sensibilidad de malla para garantizar la convergencia de la predicción de pérdida de carga. Se evaluaron distintos espesores y velocidades de entrada usando los modelos de turbulencia kappa-omega SST y kappa-epsilon realizable, y los resultados se compararon con datos de paneles similares de la literatura industrial. Para incorporar la transferencia de calor, se utilizó el solver buoyantSimpleFoam, resolviendo la ecuación de energía y extrayendo la diferencia de entalpía entre entrada y salida para calcular la tasa de transferencia térmica. A partir de estos datos se obtuvo el coeficiente convectivo medio y el número de Nusselt asociado. Este primer alcance numérico sienta las bases para futuros estudios que incorporen fenómenos de evaporación y la caracterización completa de la capacidad de enfriamiento.
- 13 December 2025
- Published by Asociación Argentina De Mecánica Computacional in Resúmenes de Mecánica Computacional
- Vol. 2 (2) , 27
Open AccessEstudio CFD de Paneles Evaporativos de Celulosa para Evaluar Pérdida de Carga y Transferencia de Calor
Los paneles evaporativos de celulosa constituyen una solución de bajo consumo energético para la climatización de grandes espacios industriales y agrícolas, aprovechando el enfriamiento por evaporación del agua. Sin embargo, su caracterización técnica detallada en condiciones reales de operación es limitada. En este trabajo se presenta un estudio preliminar por CFD de un panel fabricado por DollTec, mediante simulaciones full 3D en OpenFOAM. Se modeló una sección representativa del panel y se llevó a cabo un análisis de sensibilidad de malla para garantizar la convergencia de la predicción de pérdida de carga. Se evaluaron distintos espesores y velocidades de entrada usando los modelos de turbulencia kappa-omega SST y kappa-epsilon realizable, y los resultados se compararon con datos de paneles similares de la literatura industrial. Para incorporar la transferencia de calor, se utilizó el solver buoyantSimpleFoam, resolviendo la ecuación de energía y extrayendo la diferencia de entalpía entre entrada y salida para calcular la tasa de transferencia térmica. A partir de estos datos se obtuvo el coeficiente convectivo medio y el número de Nusselt asociado. Este primer alcance numérico sienta las bases para futuros estudios que incorporen fenómenos de evaporación y la caracterización completa de la capacidad de enfriamiento.
- Open Access
- 8 February 2025
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 437
A multiscale Pseudo-DNS approach for solving turbulent boundary-layer problems
- 8 February 2025
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 437
Open AccessA multiscale Pseudo-DNS approach for solving turbulent boundary-layer problems
- 4 January 2024
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 245
Aerodynamic study of a moving Ahmed body by numerical simulation
- 4 January 2024
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 245
Aerodynamic study of a moving Ahmed body by numerical simulation
- Open Access
Validation and Enhancement of a Supermesh Strategy for the CFD Simulation of Four-Stroke Internal Combustion Engines
The present paper describes and validates an efficient CFD implementation to replicate the working fluid-dynamics of a real four-stroke internal combustion engine. To do this, experimental data obtained on a single-cylinder engine are used to validate the proposed computational approach. The engine domain is divided into regions according to each moving zone, and these are coupled using a pseudo-supermesh interface presented in a previous work by the authors. In this work, the original pseudo-supermesh strategy is enhanced by introducing the dual-boundary concept to model the valve opening/closing events to increase the accuracy and simplicity of the simulation procedure. The results produced by the proposed software tool show a good correlation to the experimental measurements of the complete engine cycle. Macroscopic quantities of the in-cylinder flow are accurately replicated as well as the instantaneous evolution of the in-cylinder and intake manifold pressure. Furthermore, the present work shows that the computational efficiency and scalability of the enhanced pseudo-supermesh approach are preserved even when applied to more complex real problems. In this sense, this work contributes to a new engineering tool promoting the enhanced pseudo-supermeshes as an effective tool for the design, development, and optimization of internal combustion engines.
Open AccessValidation and Enhancement of a Supermesh Strategy for the CFD Simulation of Four-Stroke Internal Combustion Engines
The present paper describes and validates an efficient CFD implementation to replicate the working fluid-dynamics of a real four-stroke internal combustion engine. To do this, experimental data obtained on a single-cylinder engine are used to validate the proposed computational approach. The engine domain is divided into regions according to each moving zone, and these are coupled using a pseudo-supermesh interface presented in a previous work by the authors. In this work, the original pseudo-supermesh strategy is enhanced by introducing the dual-boundary concept to model the valve opening/closing events to increase the accuracy and simplicity of the simulation procedure. The results produced by the proposed software tool show a good correlation to the experimental measurements of the complete engine cycle. Macroscopic quantities of the in-cylinder flow are accurately replicated as well as the instantaneous evolution of the in-cylinder and intake manifold pressure. Furthermore, the present work shows that the computational efficiency and scalability of the enhanced pseudo-supermesh approach are preserved even when applied to more complex real problems. In this sense, this work contributes to a new engineering tool promoting the enhanced pseudo-supermeshes as an effective tool for the design, development, and optimization of internal combustion engines.
- 1 February 2020
- Published by Elsevier in Computers & Fluids
- Vol. 198
A SIMPLE-based algorithm with enhanced velocity corrections: The COMPLEX method
- 1 February 2020
- Published by Elsevier in Computers & Fluids
- Vol. 198
A SIMPLE-based algorithm with enhanced velocity corrections: The COMPLEX method
- 1 October 2019
- Published by Elsevier in Journal of Computational Physics
- Vol. 395, 144-165
Conservative interpolation on surface interfaces for transport problems in the Finite Volume Method
- 1 October 2019
- Published by Elsevier in Journal of Computational Physics
- Vol. 395, 144-165
Conservative interpolation on surface interfaces for transport problems in the Finite Volume Method
- 1 August 2019
- Published by Elsevier in Computers & Fluids
- Vol. 190, 30-48
Implementation and validation of a Lagrangian spray model using experimental data of the ECN Spray G injector
- 1 August 2019
- Published by Elsevier in Computers & Fluids
- Vol. 190, 30-48
Implementation and validation of a Lagrangian spray model using experimental data of the ECN Spray G injector
- 1 March 2019
- Published by Elsevier in Journal of Computational Physics
- Vol. 380, 295-310
A second-order in time and space particle-based method to solve flow problems on arbitrary meshes
- 1 March 2019
- Published by Elsevier in Journal of Computational Physics
- Vol. 380, 295-310
A second-order in time and space particle-based method to solve flow problems on arbitrary meshes
- 1 July 2018
- Published by Elsevier in Journal of Computational Physics
- Vol. 365, 135-148
An oscillation-free flow solver based on flux reconstruction
- 1 July 2018
- Published by Elsevier in Journal of Computational Physics
- Vol. 365, 135-148
An oscillation-free flow solver based on flux reconstruction