Menandro N. Acda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Menandro N. Acda has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Bridgid Lai Fui Chin
Department of Chemical and Energy Engineering, Faculty of Engineering and Science, Curtin University Malaysia, CDT 250, 98009 Miri, Sarawak, Malaysia
4 shared publications - Adrian Chun Minh Loy
Department of Chemical Engineering The University of Melbourne Parkville Victoria Australia
3 shared publications Elisabeth Rianawati
Resilience Development Initiative, Jl. Imperial Imperial 2, No. 52, Bandung 40135, Indonesia
3 shared publicationsAnne Patricia G. Cantalejo
Department of Forest Products and Paper Science, University of the Philippines Los Banos College, Laguna, Philippines
2 shared publicationsDarren Kin Wai Gan
Department of Chemical Engineering, Faculty of Engineering and Science, Curtin University Malaysia, CDT 250, 98009 Miri Sarawak, Malaysia
2 shared publications- Man Kee Lam
Department of Chemical Engineering, Centre for Biofuel and Biochemical Research, Institute of Self-Sustainable Building, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Perak Darul Ridzuan, Malaysia
2 shared publications
Latest Publications
- Open Access
- 26 November 2025
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 21
Polymethylmethacrylate and polydimethylsiloxane coatings with nano TiO2 and ZnO: Surface property and resistance against drywood termite
- 26 November 2025
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 21
Open AccessPolymethylmethacrylate and polydimethylsiloxane coatings with nano TiO2 and ZnO: Surface property and resistance against drywood termite
- 2 May 2025
- Published by BioResources in BioResources
- Vol. 20 (3)
Thermal conductivity of plantation wood species and selected tropical hardwoods from the Philippines
This study investigated the transverse thermal conductivity of low-density plantation wood species and tropical hardwoods from the Philippines using the guarded hot-plate method. Results showed that thermal conductivity of low density, plantation species and denser tropical hardwoods ranged from 0.128 to 0.188 W/mK and 0.161 to 0.300 W/mK, respectively. Thermal conductivity was directly influenced by both density and moisture content of wood. Transverse thermal conductivity increased by 0.73% and 1.79% per percent increase in MC from 0% to 21% MC for low density (500 kg/m3) wood, respectively. Linear regression models fitted for thermal conductivity and ovendry density indicated a strong fit. However, there was a poor to moderate relationship between thermal conductivity and MC. The results of the present study may be of interest in the conversion of woody biomass to bioenergy or to building designers looking for natural materials to improve energy performance and efficiency of wood structures where heat transfer and temperature control are a significant economic consideration.
- 2 May 2025
- Published by BioResources in BioResources
- Vol. 20 (3)
Thermal conductivity of plantation wood species and selected tropical hardwoods from the Philippines
This study investigated the transverse thermal conductivity of low-density plantation wood species and tropical hardwoods from the Philippines using the guarded hot-plate method. Results showed that thermal conductivity of low density, plantation species and denser tropical hardwoods ranged from 0.128 to 0.188 W/mK and 0.161 to 0.300 W/mK, respectively. Thermal conductivity was directly influenced by both density and moisture content of wood. Transverse thermal conductivity increased by 0.73% and 1.79% per percent increase in MC from 0% to 21% MC for low density (500 kg/m3) wood, respectively. Linear regression models fitted for thermal conductivity and ovendry density indicated a strong fit. However, there was a poor to moderate relationship between thermal conductivity and MC. The results of the present study may be of interest in the conversion of woody biomass to bioenergy or to building designers looking for natural materials to improve energy performance and efficiency of wood structures where heat transfer and temperature control are a significant economic consideration.
- 1 November 2024
- Published by BioResources in BioResources
- Vol. 20 (1) , 725-736
Decay, mold, and termite resistance of high-density fiberboard from wood and chicken feather fibers
The decay, mold, and termite resistance of high-density fiberboard (HDF) formed using combinations of wood and chicken feather fibers (CFF) bonded with polyurethane resin was investigated. Laboratory and underground field exposure tests showed that HDF containing 50% to 100% CFF by weight were moderately to highly resistant to the white-rot fungus Pycnoporus sanguineus (L.) Murrill and the subterranean termite Coptotermes gestroi Wasmann. Moderate to heavy mold growth was observed on HDF containing 25% to 100% CFF when inoculated with a mixed strain of Aspergillus niger, Penicillium chrysogenum, and Trichoderma viride. In general, HDF consisting of wood fibers and CFF was resistant to decay and subterranean termite but susceptible to mold growth. The susceptibility HDF to mold may require the use of a biocide to improve mold resistance.
- 1 November 2024
- Published by BioResources in BioResources
- Vol. 20 (1) , 725-736
Decay, mold, and termite resistance of high-density fiberboard from wood and chicken feather fibers
The decay, mold, and termite resistance of high-density fiberboard (HDF) formed using combinations of wood and chicken feather fibers (CFF) bonded with polyurethane resin was investigated. Laboratory and underground field exposure tests showed that HDF containing 50% to 100% CFF by weight were moderately to highly resistant to the white-rot fungus Pycnoporus sanguineus (L.) Murrill and the subterranean termite Coptotermes gestroi Wasmann. Moderate to heavy mold growth was observed on HDF containing 25% to 100% CFF when inoculated with a mixed strain of Aspergillus niger, Penicillium chrysogenum, and Trichoderma viride. In general, HDF consisting of wood fibers and CFF was resistant to decay and subterranean termite but susceptible to mold growth. The susceptibility HDF to mold may require the use of a biocide to improve mold resistance.
- 1 July 2022
- Published by Bentham Science Publishers Ltd. in Current Materials Science
- Vol. 15 (2) , 154-163
High-density Fiberboard from Wood and Keratin Fibers: Physical and Mechanical Properties
Background: High-density Fiberboards (HDF) are widely used as a substitute for solid wood in furniture, cabinet, construction materials, etc. Wood fibers are often used in the production of HDF but the use of renewable materials has gained worldwide interest brought about by global pressure to pursue sustainable development. An abundant source of renewable fibers that can be used to produce HDF is keratin from waste chicken feathers. The goal of the study is to investigate the use of keratin fibers in combination with wood fibers to produce HDF. No or limited studies have been conducted in this area and if successful, it could offer an alternative utilization for the billions of kilograms of waste feather produced by the poultry industry. HDF is a high volume feather utilization that can reduce pollution and help solve solid waste disposal problems in many countries. Methods: A series of dry-formed HDFs containing varying ratios of wood and keratin fibers bonded by polyurethane resin were produced. The physical and mechanical properties of the HDFs were determined. Results : The properties of the HDFs were affected by varying ratios of wood particles and keratin fibers. Dimensional stability as indicated by low levels of thickness swelling (<4.6%) and water absorption (<10%) was observed. Internal bond (2.47 MPa), MOE (5.8 GPa) and MOR (45 MPa) values were higher or comparable to those reported in the literature. Conclusion: HDF formed using a combination of wood and keratin fibers bonded together by polyurethane resin to as much as 50% keratin fibers were dimensionally stable with stiffness and strength above the minimum requirements for general use HDF as prescribed by EN 622-5.
- 1 July 2022
- Published by Bentham Science Publishers Ltd. in Current Materials Science
- Vol. 15 (2) , 154-163
High-density Fiberboard from Wood and Keratin Fibers: Physical and Mechanical Properties
Background: High-density Fiberboards (HDF) are widely used as a substitute for solid wood in furniture, cabinet, construction materials, etc. Wood fibers are often used in the production of HDF but the use of renewable materials has gained worldwide interest brought about by global pressure to pursue sustainable development. An abundant source of renewable fibers that can be used to produce HDF is keratin from waste chicken feathers. The goal of the study is to investigate the use of keratin fibers in combination with wood fibers to produce HDF. No or limited studies have been conducted in this area and if successful, it could offer an alternative utilization for the billions of kilograms of waste feather produced by the poultry industry. HDF is a high volume feather utilization that can reduce pollution and help solve solid waste disposal problems in many countries. Methods: A series of dry-formed HDFs containing varying ratios of wood and keratin fibers bonded by polyurethane resin were produced. The physical and mechanical properties of the HDFs were determined. Results : The properties of the HDFs were affected by varying ratios of wood particles and keratin fibers. Dimensional stability as indicated by low levels of thickness swelling (<4.6%) and water absorption (<10%) was observed. Internal bond (2.47 MPa), MOE (5.8 GPa) and MOR (45 MPa) values were higher or comparable to those reported in the literature. Conclusion: HDF formed using a combination of wood and keratin fibers bonded together by polyurethane resin to as much as 50% keratin fibers were dimensionally stable with stiffness and strength above the minimum requirements for general use HDF as prescribed by EN 622-5.
- 8 December 2019
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 18 (11) , 1801-1808
Effect of Keratin Fibers on Setting and Hydration Characteristics of Portland Cement
The study investigated the effect of keratin fibers from waste chicken feather on the hydration characteristics of Type I Portland cement. The effect of varying amount of fibers on cement setting time, thermal and spectroscopic characteristics was investigated. Cement mix containing keratin fibers up to 6% by mass of cement showed increased initial and final setting times by 46% and 54%, respectively, compared to unmodified control samples. Thermal and infrared spectroscopic analyses suggest that keratin fibers possibly blocked hydrations sites or prevented cement crystallization which retarded cement curing.
- 8 December 2019
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 18 (11) , 1801-1808
Effect of Keratin Fibers on Setting and Hydration Characteristics of Portland Cement
The study investigated the effect of keratin fibers from waste chicken feather on the hydration characteristics of Type I Portland cement. The effect of varying amount of fibers on cement setting time, thermal and spectroscopic characteristics was investigated. Cement mix containing keratin fibers up to 6% by mass of cement showed increased initial and final setting times by 46% and 54%, respectively, compared to unmodified control samples. Thermal and infrared spectroscopic analyses suggest that keratin fibers possibly blocked hydrations sites or prevented cement crystallization which retarded cement curing.
- 27 October 2018
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 32 (24) , 2658-2666
Tobacco (Nicotiana tabacum) stalk particles as additive in urea formaldehyde bonded plywood
The study investigated the use of tobacco (Nicotiana tabacum L) stalk particles as additive with both extender and filler property in urea formaldehyde adhesive formulation used to bond Paraserianthes falcataria (L) Nielsen veneers into plywood. The effect of varying amount of tobacco stalk particles on adhesive working properties, shear strength and wood failure of 3-ply plywood was investigated. Adhesive mix containing urea formaldehyde resin with tobacco stalk particles up to 8% by mass blended very well and remained stable for atleast 1 hour. An increase or no significant effect on shear strength and wood failure up to 8% tobacco stalk loading was observed compared to plywood that used a commercial glue formulation. Based on shear strength and wood failure, panels containing 4–8% tobacco stalk particles would pass the requirements of ISO 12466-2. Examination of adhesive penetration and plywood strength suggest that tobacco particles could function as both filler and extender. Tobacco stalk particles offer an environmentally friendly, low cost, strong and non-abrasive alternative to conventional fibers used in plywood production.
- 27 October 2018
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 32 (24) , 2658-2666
Tobacco (Nicotiana tabacum) stalk particles as additive in urea formaldehyde bonded plywood
The study investigated the use of tobacco (Nicotiana tabacum L) stalk particles as additive with both extender and filler property in urea formaldehyde adhesive formulation used to bond Paraserianthes falcataria (L) Nielsen veneers into plywood. The effect of varying amount of tobacco stalk particles on adhesive working properties, shear strength and wood failure of 3-ply plywood was investigated. Adhesive mix containing urea formaldehyde resin with tobacco stalk particles up to 8% by mass blended very well and remained stable for atleast 1 hour. An increase or no significant effect on shear strength and wood failure up to 8% tobacco stalk loading was observed compared to plywood that used a commercial glue formulation. Based on shear strength and wood failure, panels containing 4–8% tobacco stalk particles would pass the requirements of ISO 12466-2. Examination of adhesive penetration and plywood strength suggest that tobacco particles could function as both filler and extender. Tobacco stalk particles offer an environmentally friendly, low cost, strong and non-abrasive alternative to conventional fibers used in plywood production.
- 1 October 2018
- Published by Elsevier in Bioresource Technology
- Vol. 265, 180-190
Kinetics and thermodynamic analysis in one-pot pyrolysis of rice hull using renewable calcium oxide based catalysts
- 1 October 2018
- Published by Elsevier in Bioresource Technology
- Vol. 265, 180-190
Kinetics and thermodynamic analysis in one-pot pyrolysis of rice hull using renewable calcium oxide based catalysts
- 1 August 2018
- Published by Elsevier in Bioresource Technology
- Vol. 261, 213-222
Thermogravimetric kinetic modelling of in-situ catalytic pyrolytic conversion of rice husk to bioenergy using rice hull ash catalyst
- 1 August 2018
- Published by Elsevier in Bioresource Technology
- Vol. 261, 213-222
Thermogravimetric kinetic modelling of in-situ catalytic pyrolytic conversion of rice husk to bioenergy using rice hull ash catalyst
- 1 June 2018
- Published by Elsevier in Energy Conversion and Management
- Vol. 165, 541-554
The effect of industrial waste coal bottom ash as catalyst in catalytic pyrolysis of rice husk for syngas production
- 1 June 2018
- Published by Elsevier in Energy Conversion and Management
- Vol. 165, 541-554
The effect of industrial waste coal bottom ash as catalyst in catalytic pyrolysis of rice husk for syngas production