Malachy J. O'ROurke
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Malachy J. O'ROurke has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Alojz Ivankovic
School of Mechanical and Materials Engineering, University College Dublin, D04 PR94 Dublin, Ireland
10 shared publications - Michael Gerard Connolly
School of Mechanical and Materials Engineering, University College Dublin, D04 PR94 Dublin, Ireland
10 shared publications J P McCullough
School of Electrical, Electronic and Mechanical Engineering, Centre for Material Science and Engineering, University College Dublin, Belfield, Dublin, Ireland
2 shared publicationsS. Raghunathan
Belfast, Queen's Univ., United Kingdom
2 shared publicationsDavid Kyle
Dublin, Univ. College, Ireland
1 shared publicationE. Benard
Belfast, Queen's Univ., United Kingdom
1 shared publication
Latest Publications
- Open Access
- 7 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
The next generation of rear drag reduction devices for road vehicles – the multi cavity concept
- 7 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessThe next generation of rear drag reduction devices for road vehicles – the multi cavity concept
- Open Access
- 18 January 2026
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 118
On road determination of vehicle drag coefficient using the new constant power plate method
- 18 January 2026
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 118
Open AccessOn road determination of vehicle drag coefficient using the new constant power plate method
- Open Access
- 3 September 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (17) , 9693
Developments in Drag Reduction Methods and Devices for Road Vehicles
This study presents new developments in novel drag reduction devices for road vehicles, focusing on the use of inflatable and alternative material rear drag reduction devices that employ both a single- and multi-cavity approach. The effectiveness of these devices is assessed through on-road testing using constant power measurements to evaluate the resulting drag reductions. Surface pressure measurements collected during testing are compared with CFD predictions, using both the RANS and HLES methods to evaluate how accurately pressure changes are modelled when the devices are fitted to the test vehicles. A novel method for analysing vehicle surface flow in real-world conditions is also introduced, involving the capture and processing of video-recorded tuft imagery to determine appropriate means and standard deviations for the surface flow behaviour. Additionally, the study presents the latest advancements in multi-cavity drag reduction device design, along with considerations on how such devices can significantly enhance the benefits of vehicle platooning.
- 3 September 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (17) , 9693
Open AccessDevelopments in Drag Reduction Methods and Devices for Road Vehicles
This study presents new developments in novel drag reduction devices for road vehicles, focusing on the use of inflatable and alternative material rear drag reduction devices that employ both a single- and multi-cavity approach. The effectiveness of these devices is assessed through on-road testing using constant power measurements to evaluate the resulting drag reductions. Surface pressure measurements collected during testing are compared with CFD predictions, using both the RANS and HLES methods to evaluate how accurately pressure changes are modelled when the devices are fitted to the test vehicles. A novel method for analysing vehicle surface flow in real-world conditions is also introduced, involving the capture and processing of video-recorded tuft imagery to determine appropriate means and standard deviations for the surface flow behaviour. Additionally, the study presents the latest advancements in multi-cavity drag reduction device design, along with considerations on how such devices can significantly enhance the benefits of vehicle platooning.
- Open Access
Reducing Aerodynamic Drag on Roof-Mounted Lightbars for Emergency Vehicles
This paper investigates the impact of contemporary lightbars on vehicle fuel efficiency with a focus on quantifying their effects on fuel consumption and exploring strategies to improve drag performance through modifications. Simulations showed an 8–11% increase in drag for square-back vehicles, with greater penalties outlined for vehicles with rear-slanting roofs. Given the moderate drag increase, the impact on the driving range, especially for electric vehicles, remains minimal, supporting the continued use of external lightbars. Positioning experiments suggest marginal drag reductions when lowering the lightbar to its lowest position due to additional drag effects that can be caused by the mounting mechanism in its condensed form. Angling the lightbar showed negligible drag increases up to an angle of 2.5 degrees, but beyond that, a 4% increase in drag was observed for every additional 2.5 degrees. Additionally, fitting drag-reducing ramps ahead of the lightbar yielded no significant drag savings. Noise analysis identified that the lightbar’s wake and rear surfaces were responsible for the largest production of noise. The optimal lightbar design was found to incorporate overflow rather than underflow and rear tapering in sync with roof curvature. Appendable clip-on devices for the lightbar, particularly rear clip-ons, demonstrated appreciable drag reductions of up to 2.5%. A final optimised lightbar design produced a minimal 2.8% drag increase when fitted onto an unmarked vehicle, representing a threefold improvement compared with the current generation of lightbars. This study advances the field of lightbar aerodynamics by precisely quantifying drag effects by using highly detailed geometry and examines the significance of optimal positioning, angle adjustment, and appendable clip-on devices in greater depth than any existing published work.
Open AccessReducing Aerodynamic Drag on Roof-Mounted Lightbars for Emergency Vehicles
This paper investigates the impact of contemporary lightbars on vehicle fuel efficiency with a focus on quantifying their effects on fuel consumption and exploring strategies to improve drag performance through modifications. Simulations showed an 8–11% increase in drag for square-back vehicles, with greater penalties outlined for vehicles with rear-slanting roofs. Given the moderate drag increase, the impact on the driving range, especially for electric vehicles, remains minimal, supporting the continued use of external lightbars. Positioning experiments suggest marginal drag reductions when lowering the lightbar to its lowest position due to additional drag effects that can be caused by the mounting mechanism in its condensed form. Angling the lightbar showed negligible drag increases up to an angle of 2.5 degrees, but beyond that, a 4% increase in drag was observed for every additional 2.5 degrees. Additionally, fitting drag-reducing ramps ahead of the lightbar yielded no significant drag savings. Noise analysis identified that the lightbar’s wake and rear surfaces were responsible for the largest production of noise. The optimal lightbar design was found to incorporate overflow rather than underflow and rear tapering in sync with roof curvature. Appendable clip-on devices for the lightbar, particularly rear clip-ons, demonstrated appreciable drag reductions of up to 2.5%. A final optimised lightbar design produced a minimal 2.8% drag increase when fitted onto an unmarked vehicle, representing a threefold improvement compared with the current generation of lightbars. This study advances the field of lightbar aerodynamics by precisely quantifying drag effects by using highly detailed geometry and examines the significance of optimal positioning, angle adjustment, and appendable clip-on devices in greater depth than any existing published work.
- Open Access
Reducing Aerodynamic Drag on Flatbed Trailers for Passenger Vehicles Using Novel Appendable Devices
This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most-effective initial device for reducing drag was a full trailer underside cover, which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single-, dual-, and triple-axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250 mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the multi-stage converging cavity was introduced, which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van–trailer combination.
Open AccessReducing Aerodynamic Drag on Flatbed Trailers for Passenger Vehicles Using Novel Appendable Devices
This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most-effective initial device for reducing drag was a full trailer underside cover, which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single-, dual-, and triple-axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250 mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the multi-stage converging cavity was introduced, which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van–trailer combination.
- Open Access
- 19 October 2023
- Published by MDPI AG in Preprints.org
Reducing Aerodynamic Drag on Flatbed Trailers for Passenger Vehicles using Novel Appendable Devices
This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most effective initial device for reducing drag was a full trailer underside cover which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single, dual, and triple axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the Multi-Stage Converging Cavity was introduced which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van-trailer combination.
- 19 October 2023
- Published by MDPI AG in Preprints.org
Open AccessReducing Aerodynamic Drag on Flatbed Trailers for Passenger Vehicles using Novel Appendable Devices
This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most effective initial device for reducing drag was a full trailer underside cover which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single, dual, and triple axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the Multi-Stage Converging Cavity was introduced which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van-trailer combination.
- Open Access
A Drag Reduction Study on the Aerodynamics of the Irish Taxi Sign
This comprehensive study focused on the standard taxi sign used in Ireland and its impact on drag production, fuel expenses, and CO emissions. Experimental analysis revealed that the conventional taxi sign significantly increased drag, especially when mounted on streamlined vehicles such as saloon cars, due to flow separation issues on the rear roof and rear windshield. Longitudinal reorientation of the sign offered a 14-fold reduction in drag increase compared to the traditional placement. It was found that positioning the sign in the middle of the roof offered the greatest fuel efficiency. Furthermore, the study estimated that implementing longitudinal repositioning on all Irish taxi signs could save drivers approximately EUR 832 per year and reduce national CO emissions by a substantial 22,464 tonnes annually. Comparative analyses with international taxi signs demonstrated that the Irish sign had significantly larger drag contributions, emphasizing the need for improved aerodynamics. To address the inherent drag issue, the study explored novel appendable devices and proposed alternative taxi sign designs. Among the tested solutions, a magnet-mounted front ramp proved the most effective, reducing total drag by nearly 30%. Additionally, a motorized flip-up taxi sign design demonstrated a remarkable 40% reduction in drag. Finally, a newly proposed taxi sign design, featuring longitudinal positioning and pointed triangular front and rear faces, resulted in a minimal 4.3% increase in vehicle drag compared to the baseline car.Open AccessA Drag Reduction Study on the Aerodynamics of the Irish Taxi Sign
This comprehensive study focused on the standard taxi sign used in Ireland and its impact on drag production, fuel expenses, and CO emissions. Experimental analysis revealed that the conventional taxi sign significantly increased drag, especially when mounted on streamlined vehicles such as saloon cars, due to flow separation issues on the rear roof and rear windshield. Longitudinal reorientation of the sign offered a 14-fold reduction in drag increase compared to the traditional placement. It was found that positioning the sign in the middle of the roof offered the greatest fuel efficiency. Furthermore, the study estimated that implementing longitudinal repositioning on all Irish taxi signs could save drivers approximately EUR 832 per year and reduce national CO emissions by a substantial 22,464 tonnes annually. Comparative analyses with international taxi signs demonstrated that the Irish sign had significantly larger drag contributions, emphasizing the need for improved aerodynamics. To address the inherent drag issue, the study explored novel appendable devices and proposed alternative taxi sign designs. Among the tested solutions, a magnet-mounted front ramp proved the most effective, reducing total drag by nearly 30%. Additionally, a motorized flip-up taxi sign design demonstrated a remarkable 40% reduction in drag. Finally, a newly proposed taxi sign design, featuring longitudinal positioning and pointed triangular front and rear faces, resulted in a minimal 4.3% increase in vehicle drag compared to the baseline car. - Open Access
- 4 July 2023
- Published by MDPI AG in Preprints.org
A Drag Reduction Study on The Aerodynamics of The Irish Taxi Sign
This comprehensive study focused on the standard taxi sign used in Ireland, its impact on drag production, fuel expenses, and CO2 emissions. Experimental analysis revealed that the conventional taxi sign significantly increased drag, especially when mounted on streamlined vehicles such as saloon cars, due to flow separation issues on the rear roof and rear windshield. Longitudinal reorientation of the sign offered a 14-fold reduction in drag increase compared to the traditional placement. It was found that positioning the sign in the middle of the roof offered the greatest fuel efficiency. Furthermore, the study estimated that implementing longitudinal repositioning on all Irish taxi signs could save drivers approximately 832 per year and reduce national CO2 emissions by a substantial 22,464 tonnes annually. Comparative analyses with international taxi signs demonstrated that the Irish sign had significantly larger drag contributions, emphasizing the need for improved aerodynamics. To address the inherent drag issue, the study explored novel appendable devices and proposed alternative taxi sign designs. Among the tested solutions, a magnet-mounted front ramp proved the most effective, reducing total drag by nearly 30%. Additionally, a motorized flip-up taxi sign design demonstrated a remarkable 40% reduction in drag. Finally, a newly proposed taxi sign design, featuring longitudinal positioning and pointed triangular front and rear faces, resulted in a minimal 4.3% increase in vehicle drag compared to the baseline car.
- 4 July 2023
- Published by MDPI AG in Preprints.org
Open AccessA Drag Reduction Study on The Aerodynamics of The Irish Taxi Sign
This comprehensive study focused on the standard taxi sign used in Ireland, its impact on drag production, fuel expenses, and CO2 emissions. Experimental analysis revealed that the conventional taxi sign significantly increased drag, especially when mounted on streamlined vehicles such as saloon cars, due to flow separation issues on the rear roof and rear windshield. Longitudinal reorientation of the sign offered a 14-fold reduction in drag increase compared to the traditional placement. It was found that positioning the sign in the middle of the roof offered the greatest fuel efficiency. Furthermore, the study estimated that implementing longitudinal repositioning on all Irish taxi signs could save drivers approximately 832 per year and reduce national CO2 emissions by a substantial 22,464 tonnes annually. Comparative analyses with international taxi signs demonstrated that the Irish sign had significantly larger drag contributions, emphasizing the need for improved aerodynamics. To address the inherent drag issue, the study explored novel appendable devices and proposed alternative taxi sign designs. Among the tested solutions, a magnet-mounted front ramp proved the most effective, reducing total drag by nearly 30%. Additionally, a motorized flip-up taxi sign design demonstrated a remarkable 40% reduction in drag. Finally, a newly proposed taxi sign design, featuring longitudinal positioning and pointed triangular front and rear faces, resulted in a minimal 4.3% increase in vehicle drag compared to the baseline car.