Deepa Prabhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Deepa Prabhu has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Jilna Jomy
5 shared publicationsP. R. Prabhu
Department of Mechatronics, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
4 shared publicationsPadmalatha Rao
Department of Chemistry, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
3 shared publications- Padmalatha Rao
Department of Chemistry, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
3 shared publications - Jilna Jomy2 shared publications
- Raghavendra Prabhu Parkala
Department of Mechatronics, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
2 shared publications
Latest Publications
- Open Access
- 3 September 2026
- Published by Elsevier in Current Research in Green and Sustainable Chemistry
- Vol. 13
Beyond passive barriers: Evolution toward sustainable and responsive coatings for marine corrosion protection
- 3 September 2026
- Published by Elsevier in Current Research in Green and Sustainable Chemistry
- Vol. 13
Open AccessBeyond passive barriers: Evolution toward sustainable and responsive coatings for marine corrosion protection
- Open Access
- 12 June 2025
- Published by Elsevier in Journal of the Taiwan Institute of Chemical Engineers
- Vol. 174
Biopolymer Xylan as a novel green corrosion inhibitor for AISI 5140 steel and copper in H2SO4 medium
- 12 June 2025
- Published by Elsevier in Journal of the Taiwan Institute of Chemical Engineers
- Vol. 174
Open AccessBiopolymer Xylan as a novel green corrosion inhibitor for AISI 5140 steel and copper in H2SO4 medium
- Open Access
- 28 November 2024
- Published by Elsevier in Current Research in Green and Sustainable Chemistry
- Vol. 9
Metal organic frameworks as a corrosion inhibitor-highlighting their structural properties along with synthetic methods and its mechanism-A review
- 28 November 2024
- Published by Elsevier in Current Research in Green and Sustainable Chemistry
- Vol. 9
Open AccessMetal organic frameworks as a corrosion inhibitor-highlighting their structural properties along with synthetic methods and its mechanism-A review
- Open Access
- 4 September 2024
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 60 (1) , 62-76
Custom design approach of design of experiment as a tool for the optimisation of parameters for corrosion inhibition study of (+)-arabinogalactan on AISI 5140 steel
Biopolymers have become prevalent in industries to prevent acid corrosion because of their robust structure and biodegradability. The current research investigates the effectiveness of the biopolymer (+)-arabinogalactan (AG) in inhibiting corrosion on AISI 5140 steel in H2SO4 media, employing a novel approach to experimental design called the custom design of experiment (DoE). Temperature and medium concentration have the greatest effects on the response, according to p-value analysis. The highest inhibitory efficiency (IE) at 50 °C, 0.1 M H2SO4 concentration, and 0.1 g/L of AG is predicted to be 75.57%. Density functional theory-based computational investigations demonstrate the potential of AG as a corrosion inhibitor, with chemisorption being the primary mode of adsorption. AG's adsorption on the metal surface is further confirmed by scanning electron microscope and energy-dispersive X-ray studies. Thus, this study pioneers the application of custom DoE in investigating AG's corrosion inhibition properties on AISI 5140 steel in H2SO4 medium.
- 4 September 2024
- Published by SAGE Publications in Corrosion Engineering, Science and Technology: The International Journal of Corrosion Processes and Corrosion Control
- Vol. 60 (1) , 62-76
Open AccessCustom design approach of design of experiment as a tool for the optimisation of parameters for corrosion inhibition study of (+)-arabinogalactan on AISI 5140 steel
Biopolymers have become prevalent in industries to prevent acid corrosion because of their robust structure and biodegradability. The current research investigates the effectiveness of the biopolymer (+)-arabinogalactan (AG) in inhibiting corrosion on AISI 5140 steel in H2SO4 media, employing a novel approach to experimental design called the custom design of experiment (DoE). Temperature and medium concentration have the greatest effects on the response, according to p-value analysis. The highest inhibitory efficiency (IE) at 50 °C, 0.1 M H2SO4 concentration, and 0.1 g/L of AG is predicted to be 75.57%. Density functional theory-based computational investigations demonstrate the potential of AG as a corrosion inhibitor, with chemisorption being the primary mode of adsorption. AG's adsorption on the metal surface is further confirmed by scanning electron microscope and energy-dispersive X-ray studies. Thus, this study pioneers the application of custom DoE in investigating AG's corrosion inhibition properties on AISI 5140 steel in H2SO4 medium.
- Open Access
- 1 September 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (9) , 096506
Sodium salt of dodecyl benzene sulphonic acid as an effective corrosion inhibition for different heat-treated steel in sulphuric acid medium
The purpose of this work is to use electrochemical and gravimetric techniques to investigate the inhibition of DBSS on the corrosion of heat-treated dual-phase AISI 1040 steel in a 0.5 M sulphuric acid solution at 35 °C. The corrosion studies are performed by potentiodynamic polarization study (PDP), electrochemical impedance study (EIS), and gravimetric method. To confirm the inhibition surface characterization like x-ray diffraction technique (XRD) analysis, scanning electron microscopy (SEM), and EDS analysis are performed. Depending on the phase change of metals due to heat treatment, the corrosion inhibition of the heat-treated metal increased when it was exposed to 0.5 M H2SO4 at 35 °C in the presence of dodecyl benzene sulphonic acid sodium salt (DBSS) inhibitor. The highest inhibition efficiency of 63%, 82%, 87%, 43%, and 63% was obtained for AISI 1040 steel at heat treatment conditions of Normalized, Quenched at 700 °C, Quenched at 750 °C, Quenched at 790 °C and Quenched at 900 °C respectively. In the gravimetric and electrochemical study, the IE increases with the increase with the concentration of DBSS unto 75% from gravimetric analysis and 87% from PDP analysis for Quenched at 750 °C and 790 °C respectively. The metal protection is achieved by heat treatment process as well as by using DBSS as inhibitor. Corrosion inhibition on the metal’s surface was confirmed by SEM and XRD. In addition, the adsorption of DBSS on the anodic and cathodic sites of the metal surface was well explained.
- 1 September 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (9) , 096506
Open AccessSodium salt of dodecyl benzene sulphonic acid as an effective corrosion inhibition for different heat-treated steel in sulphuric acid medium
The purpose of this work is to use electrochemical and gravimetric techniques to investigate the inhibition of DBSS on the corrosion of heat-treated dual-phase AISI 1040 steel in a 0.5 M sulphuric acid solution at 35 °C. The corrosion studies are performed by potentiodynamic polarization study (PDP), electrochemical impedance study (EIS), and gravimetric method. To confirm the inhibition surface characterization like x-ray diffraction technique (XRD) analysis, scanning electron microscopy (SEM), and EDS analysis are performed. Depending on the phase change of metals due to heat treatment, the corrosion inhibition of the heat-treated metal increased when it was exposed to 0.5 M H2SO4 at 35 °C in the presence of dodecyl benzene sulphonic acid sodium salt (DBSS) inhibitor. The highest inhibition efficiency of 63%, 82%, 87%, 43%, and 63% was obtained for AISI 1040 steel at heat treatment conditions of Normalized, Quenched at 700 °C, Quenched at 750 °C, Quenched at 790 °C and Quenched at 900 °C respectively. In the gravimetric and electrochemical study, the IE increases with the increase with the concentration of DBSS unto 75% from gravimetric analysis and 87% from PDP analysis for Quenched at 750 °C and 790 °C respectively. The metal protection is achieved by heat treatment process as well as by using DBSS as inhibitor. Corrosion inhibition on the metal’s surface was confirmed by SEM and XRD. In addition, the adsorption of DBSS on the anodic and cathodic sites of the metal surface was well explained.
- Open Access
- 12 June 2024
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 408
ZnO-functionalized arabinogalactan and xylan nanocomposite epoxy coating for the corrosion protection of AISI 5140 steel
- 12 June 2024
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 408
Open AccessZnO-functionalized arabinogalactan and xylan nanocomposite epoxy coating for the corrosion protection of AISI 5140 steel
- Open Access
- 22 December 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (18) , 8247-8261
Corrosion Behavior of EN18 Steel and Copper in the Sulfuric Acid Medium for As-Bought and Annealed Materials
EN18 steel and copper are used as materials for oil and gas industries for chemical storage, which come in contact with the sulfuric acid medium during the pickling process. In such instances cleaning of impurities and oxide layer removal, leads to excessive corrosion. Thus, the improvement in the microstructure through annealing treatment and its effect on the corrosion behavior of EN18 steel and copper are studied by immersing in 0.5 M H2SO4 for as-bought and 0.5, 0.25, 0.1 M H2SO4 medium solutions after annealing treatment. The metal specimens were heated to 900 °C for EN18 steel and 600 °C for copper and then both were furnace cooled and the change in the microstructure of annealed and as-received metal specimens was analyzed using Scanning Electron microscopy (SEM). The Electrochemical Impedance Spectroscopy (EIS) and Potentiodynamic polarization (PDP) measurement showed that there is a decrease in the corrosion rate for both metals after annealing treatment. The effect of corrosion rate at the temperature range of 30-50 °C was analyzed and activation parameters were described using Arrhenius and transition state theories. Suitable corrosion mechanisms for both steel and copper in the H2SO4 medium have been discussed.
- 22 December 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (18) , 8247-8261
Open AccessCorrosion Behavior of EN18 Steel and Copper in the Sulfuric Acid Medium for As-Bought and Annealed Materials
EN18 steel and copper are used as materials for oil and gas industries for chemical storage, which come in contact with the sulfuric acid medium during the pickling process. In such instances cleaning of impurities and oxide layer removal, leads to excessive corrosion. Thus, the improvement in the microstructure through annealing treatment and its effect on the corrosion behavior of EN18 steel and copper are studied by immersing in 0.5 M H2SO4 for as-bought and 0.5, 0.25, 0.1 M H2SO4 medium solutions after annealing treatment. The metal specimens were heated to 900 °C for EN18 steel and 600 °C for copper and then both were furnace cooled and the change in the microstructure of annealed and as-received metal specimens was analyzed using Scanning Electron microscopy (SEM). The Electrochemical Impedance Spectroscopy (EIS) and Potentiodynamic polarization (PDP) measurement showed that there is a decrease in the corrosion rate for both metals after annealing treatment. The effect of corrosion rate at the temperature range of 30-50 °C was analyzed and activation parameters were described using Arrhenius and transition state theories. Suitable corrosion mechanisms for both steel and copper in the H2SO4 medium have been discussed.
- Open Access
- 21 February 2022
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 8 (2) , 1-15
Inhibitors Incorporated Into Water-Based Epoxy Coatings on Metals for Corrosion Protection: A Review
Corrosion and its protection are one of the major challenges that are faced by the industries. To overcome this, new coatings with characteristic properties which are environmentally friendly are introduced. A cost-effective and most reliable way of corrosion protection is via barrier coatings, in which water-based epoxy coatings showed significant corrosion resistance. Although the epoxy coating creates a barrier between the metal and the corroding ions, there is a chance of leakage due to mechanical rupture and the formation of micropores during the curing time of the epoxy. This leads to the incorporation of inhibitors into the epoxy coatings which in turn increase the corrosion resistance. This review discusses the different types of inhibitors that are incorporated into the epoxy coating to prevent corrosion. The use of Nano/micro containers for the encapsulation of the inhibitors leads to the discovery of self-healing smart coatings. Such water-based epoxy smart coatings are also discussed.
- 21 February 2022
- Published by Springer Nature in Journal of Bio- and Tribo-Corrosion
- Vol. 8 (2) , 1-15
Open AccessInhibitors Incorporated Into Water-Based Epoxy Coatings on Metals for Corrosion Protection: A Review
Corrosion and its protection are one of the major challenges that are faced by the industries. To overcome this, new coatings with characteristic properties which are environmentally friendly are introduced. A cost-effective and most reliable way of corrosion protection is via barrier coatings, in which water-based epoxy coatings showed significant corrosion resistance. Although the epoxy coating creates a barrier between the metal and the corroding ions, there is a chance of leakage due to mechanical rupture and the formation of micropores during the curing time of the epoxy. This leads to the incorporation of inhibitors into the epoxy coatings which in turn increase the corrosion resistance. This review discusses the different types of inhibitors that are incorporated into the epoxy coating to prevent corrosion. The use of Nano/micro containers for the encapsulation of the inhibitors leads to the discovery of self-healing smart coatings. Such water-based epoxy smart coatings are also discussed.
- Open Access
- 17 July 2021
- Published by Springer Nature in Chemical Papers
- Vol. 75 (11) , 6083-6099
Chemical, electrochemical, thermodynamic and adsorption study of EN8 dual-phase steel with ferrite-martensite structure in 0.5 M H2SO4 using pectin as inhibitor
This paper presents the corrosion and inhibition behavior of heat-treated EN8 dual-phase steel with ferrite-martensite structure with pectin in 0.5 M sulphuric acid. The corrosion studies were performed using the weight loss method, electrochemical techniques such as potentiodynamic polarization measurements, and impedance spectroscopy. The study was done at different concentrations of pectin in the temperature range of 40 to 70 °C and immersion time of 1, 3, 5, and 7 h. The results showed that the inhibition performance of pectin has enhanced with an increase in pectin concentration and decreased with the temperature and time of exposure. From the weight loss study, highest inhibition efficiency of 76.43% was achieved at 5.0 g/L at 1 h of exposure at 40 °C. The maximum inhibition efficiency of 62% was obtained with 5.0 g/L of pectin at 40 °C by potentiodynamic polarization method. The energy, enthalpy, and entropy of activation and also thermodynamic parameters like free energy, enthalpy, and entropy of adsorption were assessed and discussed. Appropriate adsorption isotherm was fit to the obtained experimental outcomes and achieved Langmuir adsorption isotherm to be the best fit and obeyed physical adsorption. Surface analysis: scanning electron microscopy, X-ray diffraction techniques, atomic force microscopy, and energy dispersive X-ray were done with and without the addition of pectin. The metal surface appears to be uniform and smooth in the presence of pectin and adsorption was confirmed by surface analysis.
- 17 July 2021
- Published by Springer Nature in Chemical Papers
- Vol. 75 (11) , 6083-6099
Open AccessChemical, electrochemical, thermodynamic and adsorption study of EN8 dual-phase steel with ferrite-martensite structure in 0.5 M H2SO4 using pectin as inhibitor
This paper presents the corrosion and inhibition behavior of heat-treated EN8 dual-phase steel with ferrite-martensite structure with pectin in 0.5 M sulphuric acid. The corrosion studies were performed using the weight loss method, electrochemical techniques such as potentiodynamic polarization measurements, and impedance spectroscopy. The study was done at different concentrations of pectin in the temperature range of 40 to 70 °C and immersion time of 1, 3, 5, and 7 h. The results showed that the inhibition performance of pectin has enhanced with an increase in pectin concentration and decreased with the temperature and time of exposure. From the weight loss study, highest inhibition efficiency of 76.43% was achieved at 5.0 g/L at 1 h of exposure at 40 °C. The maximum inhibition efficiency of 62% was obtained with 5.0 g/L of pectin at 40 °C by potentiodynamic polarization method. The energy, enthalpy, and entropy of activation and also thermodynamic parameters like free energy, enthalpy, and entropy of adsorption were assessed and discussed. Appropriate adsorption isotherm was fit to the obtained experimental outcomes and achieved Langmuir adsorption isotherm to be the best fit and obeyed physical adsorption. Surface analysis: scanning electron microscopy, X-ray diffraction techniques, atomic force microscopy, and energy dispersive X-ray were done with and without the addition of pectin. The metal surface appears to be uniform and smooth in the presence of pectin and adsorption was confirmed by surface analysis.
- Open Access
- 1 January 2021
- Published by Taylor & Francis in Cogent Engineering
- Vol. 8 (1)
Corrosion inhibition of ferrite bainite AISI1040 steel in H2SO4 using biopolymer
The purpose of this study is to investigate the corrosion behavior of the ferrite-bainite phase of AISI1040 steel and its corrosion inhibition using pectin in 0.5 M sulphuric acid medium. The corrosion study was conducted through weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements. The study was conducted within the temperature range of 313–343 K and immersion time of 1 h— 7 h. The inhibition performance of pectin has boosted with an increase in the concentration of pectin and decreased with the temperature and time of exposure. From the weight loss study, the highest inhibition efficiency of 85% was achieved at 5.0 g/L at 1 h of exposure at 40 °C. The activation, thermodynamic, and adsorption isotherm were adapted for the experimental results. The energy and enthalpy of activation emphasized on energy barrier for the corrosion process. The entropy of activation values is negative, indicating the association of molecules. The physical adsorption of pectin on the metal surface was confirmed by the free energy of adsorption (close to-20kj mol−1). The enthalpy of adsorption indicated the exothermic process and, arrangement of the molecules on the surface of the metal expressed by the entropy of adsorption. The optimum efficiency of 74.9% is achieved for the addition of 5.0 g/L of pectin at 313 K by the EIS technique. Surface analyses involving a scanning electron microscope and atomic force microscopy were carried out to understand the nature of the surface in the presence and absence of pectin.
- 1 January 2021
- Published by Taylor & Francis in Cogent Engineering
- Vol. 8 (1)
Open AccessCorrosion inhibition of ferrite bainite AISI1040 steel in H2SO4 using biopolymer
The purpose of this study is to investigate the corrosion behavior of the ferrite-bainite phase of AISI1040 steel and its corrosion inhibition using pectin in 0.5 M sulphuric acid medium. The corrosion study was conducted through weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements. The study was conducted within the temperature range of 313–343 K and immersion time of 1 h— 7 h. The inhibition performance of pectin has boosted with an increase in the concentration of pectin and decreased with the temperature and time of exposure. From the weight loss study, the highest inhibition efficiency of 85% was achieved at 5.0 g/L at 1 h of exposure at 40 °C. The activation, thermodynamic, and adsorption isotherm were adapted for the experimental results. The energy and enthalpy of activation emphasized on energy barrier for the corrosion process. The entropy of activation values is negative, indicating the association of molecules. The physical adsorption of pectin on the metal surface was confirmed by the free energy of adsorption (close to-20kj mol−1). The enthalpy of adsorption indicated the exothermic process and, arrangement of the molecules on the surface of the metal expressed by the entropy of adsorption. The optimum efficiency of 74.9% is achieved for the addition of 5.0 g/L of pectin at 313 K by the EIS technique. Surface analyses involving a scanning electron microscope and atomic force microscopy were carried out to understand the nature of the surface in the presence and absence of pectin.