Gernot A. Pacher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Gernot A. Pacher has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Dieter P. Gruber
Polymer Competence Center Leoben GmbH, Roseggerstrasse 12, A-8700 Leoben, Austria
5 shared publicationsWalter Friesenbichler
4 shared publications- Gerald Berger-Weber
Institute of Polymer Processing and Digital Transformation Johannes Kepler University Linz Linz Austria
3 shared publications Gerald R. Berger
Institute of Injection Molding of Polymers, Montanuniversitaet Leoben, Otto Glöckel-Straße 2, A-8700 Leoben, Austria
3 shared publicationsJohannes Macher
3 shared publications- Clemens Holzer
Department of Polymer Engineering and Science, Institute of Polymer Processing, Montanuniversitaet Leoben, Otto Gloeckel-Straße 2, 8700 Leoben, Austria
2 shared publications
Latest Publications
- 31 July 2017
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 32 (4) , 446-454
Influence of Melt Compounding on Blast Furnace Slag Filled PP Compounds: A Comparative Study
In the current study, an assessment of the melt-compounding approach upon the behavior of blast furnace slag (BFS) filled polypropylene (PP) is reported. Two melt-compounding technologies are compared in terms of thermodynamic considerations as well as final behavior of the produced compounds. For this comparison, three PP-BFS formulations are introduced, where non-treated BFS is melt-mixed with PP via (1) internal lab mixer (IM) and (2) co-rotating twin-screw compounder (TSC). PP-BFS compounds from both processes are formed into plates via compression molding, characterized and tested for rheological, thermal and mechanical behavior. Processing parameters were evaluated for both processes such as specific shear work, residence time and shear rates. In addition, the rheological, thermal and mechanical behavior of comparable compounds are evaluated. The calculated specific shear work values for IM and TSC are 0.15 and 0.1 kW · h · kg−1. Calculated residence time for TSC is 55 s. Regarding the rheological behavior, it was found that melt mixing via both technologies did not show major differences in complex viscosity or storage- and loss moduli values. DSC findings show that crystallization and melting temperatures of IM- and TSC formulations are comparable. Decreased strain values are noticed for TSC compounds, while tensile modulus is found to be independent of process variation.
- 31 July 2017
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 32 (4) , 446-454
Influence of Melt Compounding on Blast Furnace Slag Filled PP Compounds: A Comparative Study
In the current study, an assessment of the melt-compounding approach upon the behavior of blast furnace slag (BFS) filled polypropylene (PP) is reported. Two melt-compounding technologies are compared in terms of thermodynamic considerations as well as final behavior of the produced compounds. For this comparison, three PP-BFS formulations are introduced, where non-treated BFS is melt-mixed with PP via (1) internal lab mixer (IM) and (2) co-rotating twin-screw compounder (TSC). PP-BFS compounds from both processes are formed into plates via compression molding, characterized and tested for rheological, thermal and mechanical behavior. Processing parameters were evaluated for both processes such as specific shear work, residence time and shear rates. In addition, the rheological, thermal and mechanical behavior of comparable compounds are evaluated. The calculated specific shear work values for IM and TSC are 0.15 and 0.1 kW · h · kg−1. Calculated residence time for TSC is 55 s. Regarding the rheological behavior, it was found that melt mixing via both technologies did not show major differences in complex viscosity or storage- and loss moduli values. DSC findings show that crystallization and melting temperatures of IM- and TSC formulations are comparable. Decreased strain values are noticed for TSC compounds, while tensile modulus is found to be independent of process variation.
- 1 January 2017
- Published by AIP Publishing
Influence of compounding technology on rheological, thermal and mechanical behavior of blast furnace slag filled polystyrene compounds
The influence of melt-compounding technique on blast furnace slags (BFS) filled polystyrene (PS) compounds was investigated. BFS are byproducts of iron industry, and are formed during the production of iron via thermo-chemical reduction in blast furnaces. BFS are mineral-structured materials composed of severeal such as silicon oxide (SiO2), calcium oxide (CaO), magnesium oxide (MgO) and alumina (Al2O3) as well as other minor oxides and elements. Such combination of oxides might be of technical advantage if BFS is properly prepared and tailored for use as a functional filler for PS. In addition, BFS is outstandingly inexpensive and require minimal refining costs compared to common mineral fillers used in polymer industry such as calcium carbonate and talc, giving BFS an economic significance. In current study, compounds were produced via melt-compounding approach, where two different processing technologies were used: (1) Laboratory rotor-blade internal mixer (IM) and (2) co-rotating, twin-screw compounding extruder (TSC). It was found that compounding process did not yield a strong influence on the rheological properties, where comparable levels for shear viscosity, storage- and loss moduli were observed for all compounds except for ‘20G40 TSC’ compound. Such deviancy was clear in thermal properties of this particular compound, where slightly lower transition temperature (Tg) as well as higher specific heat capacity (Cp) were reported. For mechanical behavior, comparable stress-strain curves and young’s modulus values for both processes were witnessed. Deviant ‘20G40 TSC’ compound showed slightly lower young’s modulus compared to corresponding IM.
- 1 January 2017
- Published by AIP Publishing
Influence of compounding technology on rheological, thermal and mechanical behavior of blast furnace slag filled polystyrene compounds
The influence of melt-compounding technique on blast furnace slags (BFS) filled polystyrene (PS) compounds was investigated. BFS are byproducts of iron industry, and are formed during the production of iron via thermo-chemical reduction in blast furnaces. BFS are mineral-structured materials composed of severeal such as silicon oxide (SiO2), calcium oxide (CaO), magnesium oxide (MgO) and alumina (Al2O3) as well as other minor oxides and elements. Such combination of oxides might be of technical advantage if BFS is properly prepared and tailored for use as a functional filler for PS. In addition, BFS is outstandingly inexpensive and require minimal refining costs compared to common mineral fillers used in polymer industry such as calcium carbonate and talc, giving BFS an economic significance. In current study, compounds were produced via melt-compounding approach, where two different processing technologies were used: (1) Laboratory rotor-blade internal mixer (IM) and (2) co-rotating, twin-screw compounding extruder (TSC). It was found that compounding process did not yield a strong influence on the rheological properties, where comparable levels for shear viscosity, storage- and loss moduli were observed for all compounds except for ‘20G40 TSC’ compound. Such deviancy was clear in thermal properties of this particular compound, where slightly lower transition temperature (Tg) as well as higher specific heat capacity (Cp) were reported. For mechanical behavior, comparable stress-strain curves and young’s modulus values for both processes were witnessed. Deviant ‘20G40 TSC’ compound showed slightly lower young’s modulus compared to corresponding IM.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1779 (1) , 020005
Influence of rapid heat cycle molding and filler type on warpage of injection molded parts out of PP-based compounds
The aim of this work is to study the influence of Rapid Heat Cycle Molding (RHCM) and filler type on part warpage of PP-based compounds. Therefore, several PP compounds, comprising glass beads and glass bubbles, respectively, were compounded and processed in injection molding in addition to neat polypropylene. The specimen warpage was measured via confocal microscopy by scanning the specimen’s surfaces. Since the measurements are contactless, the used method allows fast and accurate acquisition of the part warpage. Experiments varying filler type and amount were carried out systematically and compared to specimens out of neat PP. It was shown that the negative influence of one-sided RHCM can be significantly reduced by using inexpensive fillers, which add the benefit of reducing material costs while increasing mechanical properties and dimensional stability.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1779 (1) , 020005
Influence of rapid heat cycle molding and filler type on warpage of injection molded parts out of PP-based compounds
The aim of this work is to study the influence of Rapid Heat Cycle Molding (RHCM) and filler type on part warpage of PP-based compounds. Therefore, several PP compounds, comprising glass beads and glass bubbles, respectively, were compounded and processed in injection molding in addition to neat polypropylene. The specimen warpage was measured via confocal microscopy by scanning the specimen’s surfaces. Since the measurements are contactless, the used method allows fast and accurate acquisition of the part warpage. Experiments varying filler type and amount were carried out systematically and compared to specimens out of neat PP. It was shown that the negative influence of one-sided RHCM can be significantly reduced by using inexpensive fillers, which add the benefit of reducing material costs while increasing mechanical properties and dimensional stability.
- 1 October 2014
- Published by Elsevier in Polymer Testing
- Vol. 39, 12-19
A novel sink mark model for high gloss injection molded parts – Correlation of deflectometric and topographic measurements
- 1 October 2014
- Published by Elsevier in Polymer Testing
- Vol. 39, 12-19
A novel sink mark model for high gloss injection molded parts – Correlation of deflectometric and topographic measurements
- 1 April 2014
- Published by Elsevier in Polymer Testing
- Vol. 34, 42-48
Detection of visually perceptible sink marks on high gloss injection molded parts by phase measuring deflectometry
- 1 April 2014
- Published by Elsevier in Polymer Testing
- Vol. 34, 42-48
Detection of visually perceptible sink marks on high gloss injection molded parts by phase measuring deflectometry
- Open Access
- 1 February 2014
- Published by Elsevier in Polymer Testing
- Vol. 33, 7-12
Measurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing model
- 1 February 2014
- Published by Elsevier in Polymer Testing
- Vol. 33, 7-12
Open AccessMeasurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing model
- 1 January 2014
- Published by AIP Publishing in AIP Conference Proceedings
- p. 179-182
In-mold sensor concept to calculate process-specific rheological properties
To gain extended knowledge on the flow behavior of polymer melts during filling phase of the injection molding process, an injection mold featuring complex sensor technology was developed. Three triple-combined FOS MTPS408 cavity sensors (FOS Messtechnik GmbH) are aligned along the flow path of a plate-shaped cavity. Each sensor features an infrared detector, a type K thermocouple, and a piezo-electric pressure detector. This configuration enables the local and transient recording of melt temperature, mold temperature and cavity pressure near gate, part center and end of part simultaneously. Averaged melt velocities are determined by evaluating the differing times of the rising edges of the infrared sensors. Local melt velocities and viscosities are calculated at each sensor position by evaluation of the gradients of temperature and pressure. Moreover, the used injection mold is equipped with RHCM technologies to additionally influence the mold surface temperature and hence the filling of the cavity. The specimens are plate-shaped parts having cut-outs and ribs similar to geometries found in numerous industrial applications such as cover panels. The application of this in-mold sensor concept provides novel possibilities for the systematic in-line analysis and evaluation of process-parameters in injection molding. Further studies will be carried out to connect the process-specific properties to the specimen morphology; aiming at controlling morphology by adjusting process parameters.
- 1 January 2014
- Published by AIP Publishing in AIP Conference Proceedings
- p. 179-182
In-mold sensor concept to calculate process-specific rheological properties
To gain extended knowledge on the flow behavior of polymer melts during filling phase of the injection molding process, an injection mold featuring complex sensor technology was developed. Three triple-combined FOS MTPS408 cavity sensors (FOS Messtechnik GmbH) are aligned along the flow path of a plate-shaped cavity. Each sensor features an infrared detector, a type K thermocouple, and a piezo-electric pressure detector. This configuration enables the local and transient recording of melt temperature, mold temperature and cavity pressure near gate, part center and end of part simultaneously. Averaged melt velocities are determined by evaluating the differing times of the rising edges of the infrared sensors. Local melt velocities and viscosities are calculated at each sensor position by evaluation of the gradients of temperature and pressure. Moreover, the used injection mold is equipped with RHCM technologies to additionally influence the mold surface temperature and hence the filling of the cavity. The specimens are plate-shaped parts having cut-outs and ribs similar to geometries found in numerous industrial applications such as cover panels. The application of this in-mold sensor concept provides novel possibilities for the systematic in-line analysis and evaluation of process-parameters in injection molding. Further studies will be carried out to connect the process-specific properties to the specimen morphology; aiming at controlling morphology by adjusting process parameters.
- 1 January 2014
- Published by AIP Publishing in AIP Conference Proceedings
Influence of mold surface temperature on polymer part warpage in rapid heat cycle molding
Dynamic mold surface temperature control was examined for its influence on the warpage. A test mold, featuring two different rapid heat cycle molding (RHCM) technologies was used to manufacture complex plate-shaped parts having different ribs, varying thin-wall regions, and both, circular and rectangular cut-outs. The mold's nozzle side is equipped with the areal heating and cooling technology BFMOLD®, where the heating/cooling channels are replaced by a ball-filled slot near the cavity surface flooded through with hot and cold water sequentially. Two local electrical ceramic heating elements are installed into the mold's ejection side. Based on a 23 full-factorial design of experiments (DoE) plan, varying nozzle temperature (Tnozzle), rapid heat cycle molding temperature (TRHCM) and holding pressure (pn), specimens of POM were manufactured systematically. Five specimens were examined per DoE run. The resulting warpage was measured at 6 surface line scans per part using the non-contact confocal topography system FRT MicroProf®. Two warpage parameters were calculated, the curvature of a 2nd order approximation a, and the vertical deflection at the profile center d. Both, the influence strength and the acting direction of the process parameters and their interactions on a and d were calculated by statistical analysis. Linear mathematical process models were determined for a and d to predict the warpage as a function of the process parameter settings. Finally, an optimum process setting was predicted, based on the process models and Microsoft Excel GRG solver. Clear and significant influences of TRHCM, pn, Tnozzle, and the interaction of TRHCM and pn were determined. While TRHCM was dominant close to the gate, pn became more effective as the flow length increased.
- 1 January 2014
- Published by AIP Publishing in AIP Conference Proceedings
Influence of mold surface temperature on polymer part warpage in rapid heat cycle molding
Dynamic mold surface temperature control was examined for its influence on the warpage. A test mold, featuring two different rapid heat cycle molding (RHCM) technologies was used to manufacture complex plate-shaped parts having different ribs, varying thin-wall regions, and both, circular and rectangular cut-outs. The mold's nozzle side is equipped with the areal heating and cooling technology BFMOLD®, where the heating/cooling channels are replaced by a ball-filled slot near the cavity surface flooded through with hot and cold water sequentially. Two local electrical ceramic heating elements are installed into the mold's ejection side. Based on a 23 full-factorial design of experiments (DoE) plan, varying nozzle temperature (Tnozzle), rapid heat cycle molding temperature (TRHCM) and holding pressure (pn), specimens of POM were manufactured systematically. Five specimens were examined per DoE run. The resulting warpage was measured at 6 surface line scans per part using the non-contact confocal topography system FRT MicroProf®. Two warpage parameters were calculated, the curvature of a 2nd order approximation a, and the vertical deflection at the profile center d. Both, the influence strength and the acting direction of the process parameters and their interactions on a and d were calculated by statistical analysis. Linear mathematical process models were determined for a and d to predict the warpage as a function of the process parameter settings. Finally, an optimum process setting was predicted, based on the process models and Microsoft Excel GRG solver. Clear and significant influences of TRHCM, pn, Tnozzle, and the interaction of TRHCM and pn were determined. While TRHCM was dominant close to the gate, pn became more effective as the flow length increased.
- 1 September 2011
- Published by Elsevier in Polymer Testing
- Vol. 30 (6) , 651-656
Novel approach to the measurement of the visual perceptibility of sink marks on injection molding parts
- 1 September 2011
- Published by Elsevier in Polymer Testing
- Vol. 30 (6) , 651-656
Novel approach to the measurement of the visual perceptibility of sink marks on injection molding parts