F. A. Hernández-García
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
F. A. Hernández-García has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Héctor Manuel Hernández García
Innovabienestar de México, SAPI de CV, Ciencia y Tecnología No. 790, Col. Saltillo 400, Saltillo 25290, Mexico
3 shared publications - Melvyn Alvarez Vera
Departamento de Ingeniería Industrial y Mecánica, Escuela de Ingeniería, Universidad de las Américas Puebla, Ex-Hacienda Santa Catarina Mártir S/N, Puebla 72810, Mexico
3 shared publications A.I. Mtz-Enriquez
Cinvestav IPN Unidad Saltillo, Km 13 Carretera Saltillo, Monterrey 25900, Coahuila, Mexico
2 shared publicationsH.M. Hdz-García
2 shared publications- Javier A. Ortega
Department of Mechanical Engineering, The University of Texas Rio Grande Valley, 1201 West University Drive, Edinburg, TX 78539, USA
2 shared publications M. Alvarez-Vera
2 shared publications
Latest Publications
- Open Access
- 28 July 2026
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 366
Effect of L-ascorbic acid reduction conditions on phase formation and physical properties of spray-pyrolyzed Cu2O thin films across different thicknesses
- 28 July 2026
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 366
Open AccessEffect of L-ascorbic acid reduction conditions on phase formation and physical properties of spray-pyrolyzed Cu2O thin films across different thicknesses
- 13 December 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 350
Micro-laser surface treatment of Ni-graphene oxide-coated Hardox 450 steel
- 13 December 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 350
Micro-laser surface treatment of Ni-graphene oxide-coated Hardox 450 steel
- 1 November 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 33 (11) , 857-865
Characterisation of PTA processed overlays without and with WC nanoparticles
Mixtures of Ni-based filler metal without and with 0.5, 1, and 2% WC nanoparticles (NPs) were methodologically tested in order to improve the wear behaviour of WC/Ni-based overlays deposited on low carbon steel by the plasma transferred arc (PTA) process. On adding 2% WC NPs, the longitudinal direction overlay microstructure was modified to have a fibrous appearance. The mechanism to improve WC particle distribution and thus prevent microcrack propagation in the overlays implies a liquid-phase viscosity change. Results of pin-on-disk tests in the overlay using filler metal with 2% WC NPs show that the combined effect of fibrous microstructure and W-rich phases in the overlay, decreases the volume loss by 76% and 78% in comparison with overlays without WC NPs for a 1 and 5 N load, respectively. These outcomes might be of interest for the mining industry, where machinery and equipment are exposed to extreme wear conditions.
- 1 November 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 33 (11) , 857-865
Characterisation of PTA processed overlays without and with WC nanoparticles
Mixtures of Ni-based filler metal without and with 0.5, 1, and 2% WC nanoparticles (NPs) were methodologically tested in order to improve the wear behaviour of WC/Ni-based overlays deposited on low carbon steel by the plasma transferred arc (PTA) process. On adding 2% WC NPs, the longitudinal direction overlay microstructure was modified to have a fibrous appearance. The mechanism to improve WC particle distribution and thus prevent microcrack propagation in the overlays implies a liquid-phase viscosity change. Results of pin-on-disk tests in the overlay using filler metal with 2% WC NPs show that the combined effect of fibrous microstructure and W-rich phases in the overlay, decreases the volume loss by 76% and 78% in comparison with overlays without WC NPs for a 1 and 5 N load, respectively. These outcomes might be of interest for the mining industry, where machinery and equipment are exposed to extreme wear conditions.