Hongkoo Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hongkoo Lee has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Hyeongdong Kim
Department of Electronic Engineering, Hanyang University, Seoul, South Korea
5 shared publications - Longyue Qu
School of Electronics and Information Engineering, Harbin Institute of Technology, Shenzhen, China
4 shared publications Hyunwoong Shin
Electronic and Computer Engineering Hanyang University Seoul, Korea
3 shared publications- Min‐Gi Kim
Department of Electronics and Computer Engineering Hanyang University Seoul Republic of Korea
3 shared publications Jihwan Jeon
Electronic and Computer Engineering, Hanyang University, Seoul, Republic of Korea
2 shared publications- Dongkwon Choi
Samsung Electronics,System LSI,Korea
1 shared publication
Latest Publications
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 117-120
Multiband Dual-Polarized Array Antenna Module for 5G Millimeter-Wave Applications
A wide multiband dual-polarized antenna array is proposed which is featuring minimized housing effects with several design strategies. We present a meandering coupled feed structure for the wideband characteristic. Also the miniaturized multiband millimetre-wave (mmWave) array antenna has been co-designed with beamforming RFIC (BFIC) to maximize the radiated power by considering load-pull effect. It was observed that the measured results showed the outstanding performance compared with a commercialized product with respect to peak EIRP and beam coverage.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 117-120
Multiband Dual-Polarized Array Antenna Module for 5G Millimeter-Wave Applications
A wide multiband dual-polarized antenna array is proposed which is featuring minimized housing effects with several design strategies. We present a meandering coupled feed structure for the wideband characteristic. Also the miniaturized multiband millimetre-wave (mmWave) array antenna has been co-designed with beamforming RFIC (BFIC) to maximize the radiated power by considering load-pull effect. It was observed that the measured results showed the outstanding performance compared with a commercialized product with respect to peak EIRP and beam coverage.
- 7 December 2018
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 61 (3) , 747-752
Antenna design using speaker wire for a Bluetooth ear set
In this article, an antenna design using an audio wire is proposed for a compact Bluetooth ear set. The length of the audio wire is less than a quarter of a wavelength in Bluetooth ear sets. Therefore, an appropriate feed structure needs to be designed to utilize the wire as an antenna. The antenna has been tuned using an inductor and impedance matching is accomplished by a loop‐type feeding structure with lumped capacitors. The feeding structure can be used to tune various lengths of the antenna. Full wave simulations are conducted to observe the effectiveness of the proposed technique. The measured and simulated bandwidths of the antenna are in good agreement. The measured bandwidth and average efficiency of the antenna were 116 MHz and 54.74%, whereas the average total isotropic sensitivity was 80.12 dBm that comply with the desired criteria for operation of the Bluetooth ear set.
- 7 December 2018
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 61 (3) , 747-752
Antenna design using speaker wire for a Bluetooth ear set
In this article, an antenna design using an audio wire is proposed for a compact Bluetooth ear set. The length of the audio wire is less than a quarter of a wavelength in Bluetooth ear sets. Therefore, an appropriate feed structure needs to be designed to utilize the wire as an antenna. The antenna has been tuned using an inductor and impedance matching is accomplished by a loop‐type feeding structure with lumped capacitors. The feeding structure can be used to tune various lengths of the antenna. Full wave simulations are conducted to observe the effectiveness of the proposed technique. The measured and simulated bandwidths of the antenna are in good agreement. The measured bandwidth and average efficiency of the antenna were 116 MHz and 54.74%, whereas the average total isotropic sensitivity was 80.12 dBm that comply with the desired criteria for operation of the Bluetooth ear set.
- 7 May 2018
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 60 (7) , 1630-1632
Antenna sensitivity enhancement using ground shorting pin
This article proposes a design technique to increase the sensitivity of Bluetooth headset antennas. A planar inverted F antenna was designed on the top printed circuit board (PCB) of a two‐board PCB. Digital noise was designed as a loop‐type source on the bottom PCB, representing general noise derived from digital circuits and digital noise generated from the main cable line. The proposed antenna design was analyzed by means of simulation and verified by means of measurements of a fabricated antenna. The proposed technique increased the measured sensitivity by 2.23 dB.
- 7 May 2018
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 60 (7) , 1630-1632
Antenna sensitivity enhancement using ground shorting pin
This article proposes a design technique to increase the sensitivity of Bluetooth headset antennas. A planar inverted F antenna was designed on the top printed circuit board (PCB) of a two‐board PCB. Digital noise was designed as a loop‐type source on the bottom PCB, representing general noise derived from digital circuits and digital noise generated from the main cable line. The proposed antenna design was analyzed by means of simulation and verified by means of measurements of a fabricated antenna. The proposed technique increased the measured sensitivity by 2.23 dB.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2469-2470
Miniaturized quadruple-band ground radiation antenna for mobile devices
A miniaturized quadruple-band ground radiation antenna within a small clearance of 7 mm × 10 mm × 1 mm is proposed for 1.575 GHz GPS band, 2.4 and 5 GHz Wi-Fi bands, as well as 3.5 GHz WiMAX band in mobile devices. The -6 dB (VSWR <; 3) impedance bandwidths of 38, 121, 114, and 542 MHz are achieved, covering the GPS band, Wi-Fi 2.4GHz band, WiMAX 3.5GHz band, and Wi-Fi 5 GHz band, respectively.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2469-2470
Miniaturized quadruple-band ground radiation antenna for mobile devices
A miniaturized quadruple-band ground radiation antenna within a small clearance of 7 mm × 10 mm × 1 mm is proposed for 1.575 GHz GPS band, 2.4 and 5 GHz Wi-Fi bands, as well as 3.5 GHz WiMAX band in mobile devices. The -6 dB (VSWR <; 3) impedance bandwidths of 38, 121, 114, and 542 MHz are achieved, covering the GPS band, Wi-Fi 2.4GHz band, WiMAX 3.5GHz band, and Wi-Fi 5 GHz band, respectively.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2171-2172
Two-layered ground radiation antenna for high efficiency applications
In this paper, a novel technique is proposed that is applicable to cases in which two-layered ground planes exist to achieve high radiation performance. The proposed ground radiation antenna is composed of a radiating loop and a feeding loop, which are built into separate two-layered ground planes. The feeding loop and radiating loop are located on the small top-layer ground plane and the large bottom-layer ground plane, respectively, so that two loops are magnetically coupled to each other, and the large bottom-layer ground plane is then excited as a radiator. The reference antenna is built with a radiating loop and a feeding loop only on the top-layer ground plane. High performances are achieved both in simulation and measurement.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2171-2172
Two-layered ground radiation antenna for high efficiency applications
In this paper, a novel technique is proposed that is applicable to cases in which two-layered ground planes exist to achieve high radiation performance. The proposed ground radiation antenna is composed of a radiating loop and a feeding loop, which are built into separate two-layered ground planes. The feeding loop and radiating loop are located on the small top-layer ground plane and the large bottom-layer ground plane, respectively, so that two loops are magnetically coupled to each other, and the large bottom-layer ground plane is then excited as a radiator. The reference antenna is built with a radiating loop and a feeding loop only on the top-layer ground plane. High performances are achieved both in simulation and measurement.
- 27 May 2016
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 58 (8) , 1806-1808
Reduction of the head effect in mobile devices
- 27 May 2016
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 58 (8) , 1806-1808
Reduction of the head effect in mobile devices
- 27 March 2015
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 57 (6) , 1400-1403
Multiband planar monopole antenna using coupling control feed structure for mobile handsets
- 27 March 2015
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 57 (6) , 1400-1403
Multiband planar monopole antenna using coupling control feed structure for mobile handsets