Rangga Adiprima Sudisman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rangga Adiprima Sudisman has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Andri Mulia
PT. Nur Straits Engineering, Department of Engineering
1 shared publicationAprika Damayanti
Universitas Pertamina
1 shared publicationArlyn Aristo Cikmit
Universitas Pertamina
1 shared publication- Arlyn Aristo Cikmit
Universitas Pertamina
1 shared publication Burhani Rizki
PT. Jaya Obayashi
1 shared publication- Diaz Ishak
University of Pertamina
1 shared publication
Latest Publications
- Open Access
- 4 March 2024
- Published by Petra Christian University in Civil Engineering Dimension
- Vol. 26 (1) , 1-10
Prediction of Soil Expansivity with Direct and Indirect Method in Banten Region, Indonesia
Expansive soils are widespread in Indonesia, particularly in Banten Province, causing extensive road damages. The study aimed to predict the soil expansivity of soil subgrade along the damaged road segments in Malingping, Cikeusik-Cibaliung, and Labuan districts. Indirect and direct expansivity predictions were employed to determine soil swelling potential. Indirect expansivity prediction was conducted based on various criteria using the Atterberg limit and grain size distribution. Direct expansivity prediction was conducted using an oedometer apparatus to measure the expansion index according to ASTM D-4829. A dynamic cone penetration test was also conducted to measure CBR values. Various indirect methods showed inconclusive results of swelling potentials, low to very high. The direct method provided more conclusive results, Expansivity Index = 100-167 and swelling values = 9%-18%, thus, categorized as expansive clay (high to very high swelling potential). CBR values were 1.49%-5% which is lower than minimum provisioned CBR (6%).
- 4 March 2024
- Published by Petra Christian University in Civil Engineering Dimension
- Vol. 26 (1) , 1-10
Open AccessPrediction of Soil Expansivity with Direct and Indirect Method in Banten Region, Indonesia
Expansive soils are widespread in Indonesia, particularly in Banten Province, causing extensive road damages. The study aimed to predict the soil expansivity of soil subgrade along the damaged road segments in Malingping, Cikeusik-Cibaliung, and Labuan districts. Indirect and direct expansivity predictions were employed to determine soil swelling potential. Indirect expansivity prediction was conducted based on various criteria using the Atterberg limit and grain size distribution. Direct expansivity prediction was conducted using an oedometer apparatus to measure the expansion index according to ASTM D-4829. A dynamic cone penetration test was also conducted to measure CBR values. Various indirect methods showed inconclusive results of swelling potentials, low to very high. The direct method provided more conclusive results, Expansivity Index = 100-167 and swelling values = 9%-18%, thus, categorized as expansive clay (high to very high swelling potential). CBR values were 1.49%-5% which is lower than minimum provisioned CBR (6%).
- 18 January 2024
- Published by Springer Nature
- p. 627-636
Gas Pipeline Stress Analysis Affected by Landslide Induced Soil Deformation
- 18 January 2024
- Published by Springer Nature
- p. 627-636
Gas Pipeline Stress Analysis Affected by Landslide Induced Soil Deformation
- Open Access
- 1 January 2023
- Published by European Alliance for Innovation n.o.
The Effect of Low Density Polyethylene Asphalt Additives on the Properties of Asphalt Concrete Wearing Course (AC-WC)
Using plastic waste in asphalt mixtures may increase the service life of the asphalt pavement surface while also reducing waste. The purpose of this study is to see how Low-Density Polyethylene (LDPE) asphalt additives affect the Marshall properties of asphalt concrete wearing course (AC-WC). 42 AC-WC pavement samples were created using the Bina Marga 2018 specification and the Indonesian National Standard for Asphalt Testing. Using the wet process, 5-8% LDPE with 0.5% intervals of the optimum asphalt content were added to the samples. Marshall tests were performed to determine the optimum asphalt and LDPE content. The optimal asphalt content was 6.5%, and the optimal plastic content was 7.5%. The results show that adding 7.5% LDPE can improve Marshall stability by two times, from 977.18 kg to 2103.44 kg, and reduce asphalt content consumption by up to 7.05% compared to the mixture without the addition of LDPE.
- 1 January 2023
- Published by European Alliance for Innovation n.o.
Open AccessThe Effect of Low Density Polyethylene Asphalt Additives on the Properties of Asphalt Concrete Wearing Course (AC-WC)
Using plastic waste in asphalt mixtures may increase the service life of the asphalt pavement surface while also reducing waste. The purpose of this study is to see how Low-Density Polyethylene (LDPE) asphalt additives affect the Marshall properties of asphalt concrete wearing course (AC-WC). 42 AC-WC pavement samples were created using the Bina Marga 2018 specification and the Indonesian National Standard for Asphalt Testing. Using the wet process, 5-8% LDPE with 0.5% intervals of the optimum asphalt content were added to the samples. Marshall tests were performed to determine the optimum asphalt and LDPE content. The optimal asphalt content was 6.5%, and the optimal plastic content was 7.5%. The results show that adding 7.5% LDPE can improve Marshall stability by two times, from 977.18 kg to 2103.44 kg, and reduce asphalt content consumption by up to 7.05% compared to the mixture without the addition of LDPE.
- Open Access
- 1 January 2023
- Published by European Alliance for Innovation n.o.
Landslide Susceptibility Classification of Musi Banyuasin Regency Using the Storie Index Method
This study aims to produce landslide susceptibility maps as a means of disaster mitigation in Musi Banyuasin Regency. The susceptibility of landslides was determined by analyzing the soil slope, rainfall intensity, soil type, land use type, and earthquake vulnerability parameters. These parameters are then scored and transformed into parameter maps. Each map is then combined with the overlay process and analyzed using the Storie Index method to determine the landslide susceptibility level. The results are divided into two categories: a landslide susceptibility map without an earthquake effect and a landslide susceptibility map with an earthquake effect. Both results show a dominance of very low landslide susceptibility levels, accounting for more than 80% of the total area of Musi Banyuasin. Overall, moderate to high landslide susceptibility occurs in areas with hilly topography, riverbanks, and areas with moderate earthquake vulnerability.
- 1 January 2023
- Published by European Alliance for Innovation n.o.
Open AccessLandslide Susceptibility Classification of Musi Banyuasin Regency Using the Storie Index Method
This study aims to produce landslide susceptibility maps as a means of disaster mitigation in Musi Banyuasin Regency. The susceptibility of landslides was determined by analyzing the soil slope, rainfall intensity, soil type, land use type, and earthquake vulnerability parameters. These parameters are then scored and transformed into parameter maps. Each map is then combined with the overlay process and analyzed using the Storie Index method to determine the landslide susceptibility level. The results are divided into two categories: a landslide susceptibility map without an earthquake effect and a landslide susceptibility map with an earthquake effect. Both results show a dominance of very low landslide susceptibility levels, accounting for more than 80% of the total area of Musi Banyuasin. Overall, moderate to high landslide susceptibility occurs in areas with hilly topography, riverbanks, and areas with moderate earthquake vulnerability.
- Open Access
- 31 December 2022
- Published by Ahli Teknik Tanah Indonesia in Indonesian Geotechnical Journal
- Vol. 1 (3) , 29-36
Swelling Prediction of Expansive Soil Using Numerical Method Analysis
Expansive soil is one of the factors that cause road damage in Indonesia. Its behavior is influenced by moisture content. At high moisture content, expansive clay has a very low bearing capacity and high swelling and shrinkage rate compared to other soil types. This soil expansion causes a heave force on the road pavement. When the force exceeds the strength of the pavement, the pavement will deform and break as the initial damage is created. Therefore, it is critical to investigate the effect of moisture content on the swelling-shrinkage behavior of expansive soil. In this study, soil expansion is numerically predicted using the finite element approach on ABAQUS compared to the laboratory expansion index test. The geometric shape and loading of the soil model are the same as the sample shape and loading of a laboratory expansion index test. The Mohr-Coulomb soil constitutive model with sorption is used to simulate water absorption in partially saturated soils. Coupled wetting liquid flow and porous medium stress analysis are used to simulate swelling and shrinkage. The simulation is divided into two types: geostatic, which simulates soil model loading, and coupled pore fluid, which simulates changes in water content. The simulation is then compared to the laboratory test for validation. The numerical analysis results show that the model's accuracy depends highly on the constitutive soil model, whereas the Mohr-Coulomb model shows a limitation in accuracy with the maximum swelling in the simulation is 21.704%, while the average maximum swelling in laboratory testing is 15.515%.
- 31 December 2022
- Published by Ahli Teknik Tanah Indonesia in Indonesian Geotechnical Journal
- Vol. 1 (3) , 29-36
Open AccessSwelling Prediction of Expansive Soil Using Numerical Method Analysis
Expansive soil is one of the factors that cause road damage in Indonesia. Its behavior is influenced by moisture content. At high moisture content, expansive clay has a very low bearing capacity and high swelling and shrinkage rate compared to other soil types. This soil expansion causes a heave force on the road pavement. When the force exceeds the strength of the pavement, the pavement will deform and break as the initial damage is created. Therefore, it is critical to investigate the effect of moisture content on the swelling-shrinkage behavior of expansive soil. In this study, soil expansion is numerically predicted using the finite element approach on ABAQUS compared to the laboratory expansion index test. The geometric shape and loading of the soil model are the same as the sample shape and loading of a laboratory expansion index test. The Mohr-Coulomb soil constitutive model with sorption is used to simulate water absorption in partially saturated soils. Coupled wetting liquid flow and porous medium stress analysis are used to simulate swelling and shrinkage. The simulation is divided into two types: geostatic, which simulates soil model loading, and coupled pore fluid, which simulates changes in water content. The simulation is then compared to the laboratory test for validation. The numerical analysis results show that the model's accuracy depends highly on the constitutive soil model, whereas the Mohr-Coulomb model shows a limitation in accuracy with the maximum swelling in the simulation is 21.704%, while the average maximum swelling in laboratory testing is 15.515%.
- Open Access
- 1 September 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 33 (3)
Experimental Investigation on Effects of Water Flow to Freezing Sand around Vertically Buried Freezing Pipe
High groundwater flow velocity is a major challenge in many artificial ground freezing (AGF) projects, especially in groundwater control projects. That condition may be unfavorable for the formation of a frozen body. This study aims to understand the effect of seepage flow on the heat transfer behavior and hydraulic conductivity variation of sand during the freezing process in AGF projects by using a vertically buried freezing pipe. The authors conducted a small-scale laboratory experiment that combined a flow test, freezing process, and infrared thermograph observations of thermal distribution. The authors prepared saturated Toyoura sand and a Toyoura–silica sand layer combination as the heat-transfer medium. The thermal distribution and hydraulic conductivity behavior were investigated by two series of freezing experiments with different sand layers and flow scenarios. Infrared thermograph observation results showed how water affects the thermal distribution characteristic, whereas flow test results showed the relation between hydraulic conductivity and frozen-body development.
- 1 September 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 33 (3)
Open AccessExperimental Investigation on Effects of Water Flow to Freezing Sand around Vertically Buried Freezing Pipe
High groundwater flow velocity is a major challenge in many artificial ground freezing (AGF) projects, especially in groundwater control projects. That condition may be unfavorable for the formation of a frozen body. This study aims to understand the effect of seepage flow on the heat transfer behavior and hydraulic conductivity variation of sand during the freezing process in AGF projects by using a vertically buried freezing pipe. The authors conducted a small-scale laboratory experiment that combined a flow test, freezing process, and infrared thermograph observations of thermal distribution. The authors prepared saturated Toyoura sand and a Toyoura–silica sand layer combination as the heat-transfer medium. The thermal distribution and hydraulic conductivity behavior were investigated by two series of freezing experiments with different sand layers and flow scenarios. Infrared thermograph observation results showed how water affects the thermal distribution characteristic, whereas flow test results showed the relation between hydraulic conductivity and frozen-body development.
- 1 March 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 31 (1)
Heat Transfer Visualization of the Application of a Cooling Pipe in Sand with Flowing Pore Water
The authors introduce an experimental method that focuses on the flow-thermal relation and the visual observation of heat distribution around a cooling pipe in sand under the flow condition. This experiment aims to understand the effect of seepage flow on the heat transfer behavior of sand under cooling and freezing conditions due to a vertically buried heat exchanger pipe. This method combines a flow test, cooling or freezing processes, and the visual observations of temperature profiles with saturated Toyoura sand as the heat transfer medium. A vertical copper pipe inserted into the sand medium is used as the thermal exchanger, while an infrared thermograph is used to measure and visualize the surface-temperature profile of the specimen. The heat transfer distribution behavior is investigated by conducting a series of cooling and freezing experiments on the specimens with variation of the flow rate condition, initial condition, and pipe depth. The thermograph observation results show how water f...
- 1 March 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 31 (1)
Heat Transfer Visualization of the Application of a Cooling Pipe in Sand with Flowing Pore Water
The authors introduce an experimental method that focuses on the flow-thermal relation and the visual observation of heat distribution around a cooling pipe in sand under the flow condition. This experiment aims to understand the effect of seepage flow on the heat transfer behavior of sand under cooling and freezing conditions due to a vertically buried heat exchanger pipe. This method combines a flow test, cooling or freezing processes, and the visual observations of temperature profiles with saturated Toyoura sand as the heat transfer medium. A vertical copper pipe inserted into the sand medium is used as the thermal exchanger, while an infrared thermograph is used to measure and visualize the surface-temperature profile of the specimen. The heat transfer distribution behavior is investigated by conducting a series of cooling and freezing experiments on the specimens with variation of the flow rate condition, initial condition, and pipe depth. The thermograph observation results show how water f...