Anish Karmakar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Anish Karmakar has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
Sudipta Patra
Department of Metallurgical Engineering, Indian Institute of Technology (BHU), Varanasi, India
9 shared publicationsDebalay Chakrabarti
Department of Metallurgical and Materials Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
6 shared publicationsKapil Dev Sharma
6 shared publicationsArnab Sarkar
Department of Metallurgical and Materials Engineering, National Institute of Technology, Rourkela, Rourkela, India
5 shared publicationsChetan Kadgaye
5 shared publicationsKaustav Barat
3 shared publications
Latest Publications
- 27 March 2026
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 79 (4)
Effect of Hydrogen Permeation on the Mechanical Responses of a X65 Linepipe Steel with Varying Microstructures
- 27 March 2026
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 79 (4)
Effect of Hydrogen Permeation on the Mechanical Responses of a X65 Linepipe Steel with Varying Microstructures
- 29 November 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (1) , 36-45
Unlocking Superior Wear Resistance in Cu-Modified Steels Through Enhanced Oxide Layer Adhesion
- 29 November 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (1) , 36-45
Unlocking Superior Wear Resistance in Cu-Modified Steels Through Enhanced Oxide Layer Adhesion
- 25 November 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 950
Tempering-microstructure reciprocity on low-cycle fatigue properties of Cu-modified Q&T steel
- 25 November 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 950
Tempering-microstructure reciprocity on low-cycle fatigue properties of Cu-modified Q&T steel
- 7 June 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (8) , 3309-3327
Tailoring the Microstructural Characteristics for Enhancing the Wear Performance of Cu-Based Low-Carbon Steel
- 7 June 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (8) , 3309-3327
Tailoring the Microstructural Characteristics for Enhancing the Wear Performance of Cu-Based Low-Carbon Steel
- 17 July 2024
- Published by Elsevier in Materialia
- Vol. 36
Strength and toughness balance in 7 %Ni steel by formation epsilon martensite, retained austenite and Low matrix strain
- 17 July 2024
- Published by Elsevier in Materialia
- Vol. 36
Strength and toughness balance in 7 %Ni steel by formation epsilon martensite, retained austenite and Low matrix strain
- 16 May 2024
- Published by Elsevier in Materialia
- Vol. 36
Ultrastructure of precipitates in Cu-modified Q&T steels and its effect on tensile responses
- 16 May 2024
- Published by Elsevier in Materialia
- Vol. 36
Ultrastructure of precipitates in Cu-modified Q&T steels and its effect on tensile responses
- 5 January 2024
- Published by Wiley in Steel Research International
- Vol. 95 (4)
Role of Cerium on the Intricacies of Deformed State and Softening Mechanisms of Low‐Carbon Steels
The present study investigates the softening kinetics of two cerium (Ce)‐modified steels after 60% cold rolling and annealing at 600 °C for 2–16 h. Cold rolling accumulates substantial strain in the ferritic matrix of low Ce (LCe) steel (0.03 wt% Ce) compared to high Ce (HCe) steel (0.6 wt% Ce). The acicular ferrite and Fe3C partition the imposed strain preferentially inside the ferrite matrix of LCe sample. Contrarily, a homogenous strain distribution in HCe sample is promoted by soft Ce2O3 particles embedded in ferrite. Both the steels achieve partial recovery and recrystallization even after 16 h of annealing. LCe steel experiences a softening fraction of ≈28 vol% after 16 h, inferior to HCe steel (≈34 vol%). During initial stage of annealing, nucleation of strain‐free grains are observed in LCe sample due to availability of grain and interphase boundaries. Subsequently, recrystallization kinetics get delayed because of the pinning effect exerted by fine CeO2 and Fe3C particles. In HCe samples, the early stage of ferrite nucleation is hindered by the segregation of Ce at grain boundaries. However, at a later stage, the recrystallization kinetics are accelerated owing to the ineffective pinning of dislocations and boundaries by coarse Ce2Fe17 and Ce2C3 particles.
- 5 January 2024
- Published by Wiley in Steel Research International
- Vol. 95 (4)
Role of Cerium on the Intricacies of Deformed State and Softening Mechanisms of Low‐Carbon Steels
The present study investigates the softening kinetics of two cerium (Ce)‐modified steels after 60% cold rolling and annealing at 600 °C for 2–16 h. Cold rolling accumulates substantial strain in the ferritic matrix of low Ce (LCe) steel (0.03 wt% Ce) compared to high Ce (HCe) steel (0.6 wt% Ce). The acicular ferrite and Fe3C partition the imposed strain preferentially inside the ferrite matrix of LCe sample. Contrarily, a homogenous strain distribution in HCe sample is promoted by soft Ce2O3 particles embedded in ferrite. Both the steels achieve partial recovery and recrystallization even after 16 h of annealing. LCe steel experiences a softening fraction of ≈28 vol% after 16 h, inferior to HCe steel (≈34 vol%). During initial stage of annealing, nucleation of strain‐free grains are observed in LCe sample due to availability of grain and interphase boundaries. Subsequently, recrystallization kinetics get delayed because of the pinning effect exerted by fine CeO2 and Fe3C particles. In HCe samples, the early stage of ferrite nucleation is hindered by the segregation of Ce at grain boundaries. However, at a later stage, the recrystallization kinetics are accelerated owing to the ineffective pinning of dislocations and boundaries by coarse Ce2Fe17 and Ce2C3 particles.
- 15 October 2023
- Published by Springer Nature
- p. 255-260
Role of Cerium on High-Temperature Oxidation Behaviour of Low-Carbon Steel
- 15 October 2023
- Published by Springer Nature
- p. 255-260
Role of Cerium on High-Temperature Oxidation Behaviour of Low-Carbon Steel
- 15 October 2023
- Published by Springer Nature
- p. 248-254
Effect of Cu on the Microstructure and Properties of Hot Rolled Low Carbon Steels
- 15 October 2023
- Published by Springer Nature
- p. 248-254
Effect of Cu on the Microstructure and Properties of Hot Rolled Low Carbon Steels