Mikhail Yu. Usanov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mikhail Yu. Usanov has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Veniamin A. Kharitonov
Nosov Magnitogorsk State Technical University
9 shared publications - Natalia M. Lokotunina
Nosov Magnitogorsk State Technical University
3 shared publications - Alexander Pesin
Laboratory of Mechanics of Gradient Nanomaterials, Nosov Magnitogorsk State Technical University, Magnitogorsk 455000, Russia
2 shared publications - Dmitry V. Terentyev
Nosov Magnitogorsk State Technical University
2 shared publications - Egor D. Melikhov2 shared publications
- Elena S. Shemetova2 shared publications
Latest Publications
- 30 June 2026
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 24 (2)
INFLUENCE OF THE DRAWING ROUTE ON THE COMPETITIVENESS OF STEEL-COPPER WIRE
The bimetallic wire manufacturing process involves two stages: the production of the blank (rod) and the finished product (wire). Based on the research and development conducted at the Nosov Magnitogorsk Mining and Metal-lurgical Institute, scientists have developed a technology for producing steel-copper rod using solid-phase metal bond-ing and implemented it at one of the enterprises in Magnitogorsk. This technology has significantly improved the adhe-sion of the sheath to the core and the stability of the wire rod drawing process. However, the issue of reducing the cost of bimetallic wire production remains unresolved. Therefore, the calculation of an efficient drawing route is of great importance, as it should ensure the production of high-quality wire with minimal manufacturing costs. For the analysis, an existing route for producing wire with a diameter of 1.15 mm has been selected, which includes three processing stages and 20 drawing passes at one of the enterprises in Magnitogorsk. In addition, a proposed drawing route has been considered, developed using a methodology created at our university, based on the evaluation of the stress-strain state of the wire in the deformation zone. The calculation results make it possible to obtain wire of the required quality level with minimal energy and material consumption. An analysis of the existing and proposed drawing routes has showed that the latter ensures process stability (safety factor values remain below the limiting values), the required wire quality due to uniform deformation across the wire cross-section, and high productivity by increasing die life and reducing the total length of wire passing through the dies. At the same time, the number of drawing passes has been reduced by 7 (or 35%), and electricity consumption has decreased by 23%. This also leads to a 35% reduction in equipment purchase costs and depreciation expenses.
- 30 June 2026
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 24 (2)
INFLUENCE OF THE DRAWING ROUTE ON THE COMPETITIVENESS OF STEEL-COPPER WIRE
The bimetallic wire manufacturing process involves two stages: the production of the blank (rod) and the finished product (wire). Based on the research and development conducted at the Nosov Magnitogorsk Mining and Metal-lurgical Institute, scientists have developed a technology for producing steel-copper rod using solid-phase metal bond-ing and implemented it at one of the enterprises in Magnitogorsk. This technology has significantly improved the adhe-sion of the sheath to the core and the stability of the wire rod drawing process. However, the issue of reducing the cost of bimetallic wire production remains unresolved. Therefore, the calculation of an efficient drawing route is of great importance, as it should ensure the production of high-quality wire with minimal manufacturing costs. For the analysis, an existing route for producing wire with a diameter of 1.15 mm has been selected, which includes three processing stages and 20 drawing passes at one of the enterprises in Magnitogorsk. In addition, a proposed drawing route has been considered, developed using a methodology created at our university, based on the evaluation of the stress-strain state of the wire in the deformation zone. The calculation results make it possible to obtain wire of the required quality level with minimal energy and material consumption. An analysis of the existing and proposed drawing routes has showed that the latter ensures process stability (safety factor values remain below the limiting values), the required wire quality due to uniform deformation across the wire cross-section, and high productivity by increasing die life and reducing the total length of wire passing through the dies. At the same time, the number of drawing passes has been reduced by 7 (or 35%), and electricity consumption has decreased by 23%. This also leads to a 35% reduction in equipment purchase costs and depreciation expenses.
- 1 May 2026
- Published by Springer Nature
- p. 51-62
Study of the Influence of Asymmetric Multi-Roll Rolling on the Stress-Strain State of Deformed Metals
- 1 May 2026
- Published by Springer Nature
- p. 51-62
Study of the Influence of Asymmetric Multi-Roll Rolling on the Stress-Strain State of Deformed Metals
- 25 December 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (4)
Application of the Combined Method “Asymmetric Rolling - Drawing in a Monolithic Die” in the Production of Wire with Fine-Grained Structure
The organization of a competitive production of wires for various applications with a fine-grained structure is currently a crucial task for the hardware manufacturing sector of domestic metallurgy. This paper describes a novel method that enables increasing the efficiency of wire production without changing the existing technological scheme. Numerical simulations were performed in the Deform-3D software package for three variants of wire manufacturing from 80R steel: drawing in a monolithic die; the combined process of “cold rolling – drawing in a monolithic die”; and a new process such as “cold asymmetric rolling – drawing in a monolithic die”. The distribution of accumulated strain in the wire obtained by these methods is evaluated. A comparative analysis of the results shows that the lowest accumulated strain values are obtained in wire drawn only in a monolithic die. In the combined process of flattening (rolling of a round blank with smooth rolls) followed by drawing in a monolithic die, the accumulated strain level increases significantly due to rolling. The application of asymmetric rolling with a ratio of the rotation speeds of the upper and lower rolls equal to 2 or 5 further increases the level of accumulated strain. It is demonstrated that the process of “cold asymmetric rolling – drawing in a monolithic die” allows for increasing the accumulated strain in the wire and thus producing a fine-grained structure without replacement of the existing equipment or infrastructure. Additionally, wide opportunities for controlling deformation modes in both the roll mill stand and monolithic die are revealed, which opens up promising ways for further improvement of the drawing process.
- 25 December 2025
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 23 (4)
Application of the Combined Method “Asymmetric Rolling - Drawing in a Monolithic Die” in the Production of Wire with Fine-Grained Structure
The organization of a competitive production of wires for various applications with a fine-grained structure is currently a crucial task for the hardware manufacturing sector of domestic metallurgy. This paper describes a novel method that enables increasing the efficiency of wire production without changing the existing technological scheme. Numerical simulations were performed in the Deform-3D software package for three variants of wire manufacturing from 80R steel: drawing in a monolithic die; the combined process of “cold rolling – drawing in a monolithic die”; and a new process such as “cold asymmetric rolling – drawing in a monolithic die”. The distribution of accumulated strain in the wire obtained by these methods is evaluated. A comparative analysis of the results shows that the lowest accumulated strain values are obtained in wire drawn only in a monolithic die. In the combined process of flattening (rolling of a round blank with smooth rolls) followed by drawing in a monolithic die, the accumulated strain level increases significantly due to rolling. The application of asymmetric rolling with a ratio of the rotation speeds of the upper and lower rolls equal to 2 or 5 further increases the level of accumulated strain. It is demonstrated that the process of “cold asymmetric rolling – drawing in a monolithic die” allows for increasing the accumulated strain in the wire and thus producing a fine-grained structure without replacement of the existing equipment or infrastructure. Additionally, wide opportunities for controlling deformation modes in both the roll mill stand and monolithic die are revealed, which opens up promising ways for further improvement of the drawing process.
- 24 December 2024
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 22 (4)
Speed Asymmetry During Cold Rolling of Round Blanks in Cylindrical Rolls
- 24 December 2024
- Published by Nosov Magnitogorsk State Technical University in Vestnik of Nosov Magnitogorsk State Technical University
- Vol. 22 (4)
Speed Asymmetry During Cold Rolling of Round Blanks in Cylindrical Rolls
- 1 March 2014
- Published by Springer Nature in Metallurgist
- Vol. 57 (11) , 1067-1072
Method of Calculating the Preforming Parameters of Wires in Cable-winding with the Use of the Deform-3D Software
- 1 March 2014
- Published by Springer Nature in Metallurgist
- Vol. 57 (11) , 1067-1072
Method of Calculating the Preforming Parameters of Wires in Cable-winding with the Use of the Deform-3D Software
- 1 March 2014
- Published by Springer Nature in Metallurgist
- Vol. 57 (11-12) , 1015-1021
Study of Radial-Shear Wire Broaching Based on Modelling
- 1 March 2014
- Published by Springer Nature in Metallurgist
- Vol. 57 (11-12) , 1015-1021
Study of Radial-Shear Wire Broaching Based on Modelling
- 1 March 2009
- Published by Springer Nature in Metallurgist
- Vol. 53 (3-4) , 236-241
Evaluating the temperature-deformation conditions on the tension pulleys of modern high-speed wet drawbenches
- 1 March 2009
- Published by Springer Nature in Metallurgist
- Vol. 53 (3-4) , 236-241
Evaluating the temperature-deformation conditions on the tension pulleys of modern high-speed wet drawbenches