Gianluca Giustolisi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gianluca Giustolisi has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- Gaetano Palumbo
Dipartimento di Ingegneria Elettrica, Elettronica e Informatica (DIEEI), Università degli Studi di Catania, 95123 Catania, Italy
57 shared publications Gaetano Palumbo
16 shared publicationsG. Palmisano
11 shared publications- Salvatore Pennisi
DIEEI (Dipartimento di Ingegneria Elettrica Elettronica e Informatica), University of Catania, 95125 Catania, Italy
10 shared publications - Andrea Ballo
University of Catania
8 shared publications - Alfio Dario Grasso
University of Catania
7 shared publications
Latest Publications
- Open Access
- 13 July 2025
- Published by MDPI AG in Electronics
- Vol. 14 (14) , 2819
A 28-nm CMOS Low-Power/Low-Voltage 60-GHz LNA for High-Speed Communication
This paper presents a wideband low-power/low-voltage 60-GHz low-noise amplifier (LNA) in a 28-nm bulk CMOS technology. The LNA has been designed for high-speed millimeter-wave (mm-wave) communications. It consists of two pseudo-differential amplifying stages and a buffer stage included for 50-Ohm on-wafer measurements. Two integrated input/output baluns guarantee both simultaneous 50-ohm input–noise/output matching at input/output radio frequency (RF) pads. A power-efficient design strategy is adopted to make the LNA suitable for low-power applications, while minimizing the noise figure (NF). Thanks to the adopted design strategy, the post-layout simulation results show an excellent trade-off between power gain and 3-dB bandwidth (BW3dB) with 13.5 dB and 7 GHz centered at 60 GHz, respectively. The proposed LNA consumes only 11.6 mA from a 0.9-V supply voltage with an NF of 8.4 dB at 60 GHz, including the input transformer loss. The input 1 dB compression point (IP1dB) of −15 dBm at 60 GHz confirms the first-rate linearity of the proposed amplifier. Human body model (HBM) electrostatic discharge (ESD) protection is guaranteed up to 2 kV at the RF input/output pads thanks to the input/output integrated transformers.
- 13 July 2025
- Published by MDPI AG in Electronics
- Vol. 14 (14) , 2819
Open AccessA 28-nm CMOS Low-Power/Low-Voltage 60-GHz LNA for High-Speed Communication
This paper presents a wideband low-power/low-voltage 60-GHz low-noise amplifier (LNA) in a 28-nm bulk CMOS technology. The LNA has been designed for high-speed millimeter-wave (mm-wave) communications. It consists of two pseudo-differential amplifying stages and a buffer stage included for 50-Ohm on-wafer measurements. Two integrated input/output baluns guarantee both simultaneous 50-ohm input–noise/output matching at input/output radio frequency (RF) pads. A power-efficient design strategy is adopted to make the LNA suitable for low-power applications, while minimizing the noise figure (NF). Thanks to the adopted design strategy, the post-layout simulation results show an excellent trade-off between power gain and 3-dB bandwidth (BW3dB) with 13.5 dB and 7 GHz centered at 60 GHz, respectively. The proposed LNA consumes only 11.6 mA from a 0.9-V supply voltage with an NF of 8.4 dB at 60 GHz, including the input transformer loss. The input 1 dB compression point (IP1dB) of −15 dBm at 60 GHz confirms the first-rate linearity of the proposed amplifier. Human body model (HBM) electrostatic discharge (ESD) protection is guaranteed up to 2 kV at the RF input/output pads thanks to the input/output integrated transformers.
- Open Access
- 31 October 2024
- Published by MDPI AG in Electronics
- Vol. 13 (21) , 4285
A 5 mW 28 nm CMOS Low-Noise Amplifier with Transformer-Based Electrostatic Discharge Protection for 60 GHz Applications
This paper presents a low-power 60 GHz low-noise amplifier (LNA) designed for Gbit/s applications using 28 nm CMOS technology. The LNA exploits a single-stage pseudo-differential architecture with integrated input transformer for both electrostatic discharge (ESD) protection and simultaneous noise/impedance matching. An effective power-constrained design strategy is adopted to pursue the lowest current consumption at the minimum noise figure (NF), with the best tradeoff between gain and frequency bandwidth. The LNA, which has been designed to drive an on–off keying (OOK) demodulator, is operated at a supply voltage as low as 0.9 V and achieves a voltage gain of about 21 dB with a 3 dB bandwidth of 2 GHz around 60 GHz. Thanks to the proper impedance transformation at the 60 GHz input, the amplifier exhibits an NF of 6.3 dB, also including the input transformer loss with a very low power consumption of about 5 mW. The adoption of a single-stage topology also allows an excellent input 1 dB compression point (IP1dB) of −4.7 dBm. The input transformer guarantees up to 2 kV human body model (HBM) ESD protection.
- 31 October 2024
- Published by MDPI AG in Electronics
- Vol. 13 (21) , 4285
Open AccessA 5 mW 28 nm CMOS Low-Noise Amplifier with Transformer-Based Electrostatic Discharge Protection for 60 GHz Applications
This paper presents a low-power 60 GHz low-noise amplifier (LNA) designed for Gbit/s applications using 28 nm CMOS technology. The LNA exploits a single-stage pseudo-differential architecture with integrated input transformer for both electrostatic discharge (ESD) protection and simultaneous noise/impedance matching. An effective power-constrained design strategy is adopted to pursue the lowest current consumption at the minimum noise figure (NF), with the best tradeoff between gain and frequency bandwidth. The LNA, which has been designed to drive an on–off keying (OOK) demodulator, is operated at a supply voltage as low as 0.9 V and achieves a voltage gain of about 21 dB with a 3 dB bandwidth of 2 GHz around 60 GHz. Thanks to the proper impedance transformation at the 60 GHz input, the amplifier exhibits an NF of 6.3 dB, also including the input transformer loss with a very low power consumption of about 5 mW. The adoption of a single-stage topology also allows an excellent input 1 dB compression point (IP1dB) of −4.7 dBm. The input transformer guarantees up to 2 kV human body model (HBM) ESD protection.
- Open Access
- 15 June 2023
- Published by MDPI AG in Electronics
- Vol. 12 (12) , 2680
Simple and Accurate Model for the Propagation Delay in MCML Gates
In this article, we develop a simple and accurate model for evaluating the propagation delay in MOS Current-Mode Logic (MCML) gates. The model describes the behavior of MCML gates in a linear fashion despite the circuits themselves being non-linear. Indeed, we demonstrate that a linear model can be used, provided that, for each small-signal parameter, its average value calculated between the two different switching logic states is used. The proposed model is validated through simulations of MCML universal gates designed using modern nanometer processes. The model forecasts simulated values with an error lower than 4% and 20% in 65-nm standard CMOS and 28-nm Fully-Depleted Silicon-On-Insulator (FD-SOI), respectively.
- 15 June 2023
- Published by MDPI AG in Electronics
- Vol. 12 (12) , 2680
Open AccessSimple and Accurate Model for the Propagation Delay in MCML Gates
In this article, we develop a simple and accurate model for evaluating the propagation delay in MOS Current-Mode Logic (MCML) gates. The model describes the behavior of MCML gates in a linear fashion despite the circuits themselves being non-linear. Indeed, we demonstrate that a linear model can be used, provided that, for each small-signal parameter, its average value calculated between the two different switching logic states is used. The proposed model is validated through simulations of MCML universal gates designed using modern nanometer processes. The model forecasts simulated values with an error lower than 4% and 20% in 65-nm standard CMOS and 28-nm Fully-Depleted Silicon-On-Insulator (FD-SOI), respectively.
- Open Access
- 8 October 2022
- Published by MDPI AG in Electronics
- Vol. 11 (19) , 3220
Hybrid Full Adders: Optimized Design, Critical Review and Comparison in the Energy-Delay Space
In this paper, we design and compare seven meaningful hybrid one-bit full adders topologies that are optimized in terms of energy-delay trade-offs to operate in multibit ripple carry adders. The goal is to provide the designer with a simple and powerful approach for choosing the best topology for a given power budget, speed performance, or any combination of both. The design and comparison deal with 4-bit and 8-bit ripple carry adders and exploit the derivation of the energy-efficient curves in the energy-delay space. To do so, first we define the procedures to obtain energy consumption and propagation delay by simulating a ripple carry adder designed at a transistor level. Then, we introduce a design methodology to optimize a ripple carry adder by minimizing some significant figures-of-merit in terms of energy-delay trade-offs. The comparison of the energy-efficient curves allows us to make a simple and effective comparison as well as to identify the best one-bit full adder topologies.
- 8 October 2022
- Published by MDPI AG in Electronics
- Vol. 11 (19) , 3220
Open AccessHybrid Full Adders: Optimized Design, Critical Review and Comparison in the Energy-Delay Space
In this paper, we design and compare seven meaningful hybrid one-bit full adders topologies that are optimized in terms of energy-delay trade-offs to operate in multibit ripple carry adders. The goal is to provide the designer with a simple and powerful approach for choosing the best topology for a given power budget, speed performance, or any combination of both. The design and comparison deal with 4-bit and 8-bit ripple carry adders and exploit the derivation of the energy-efficient curves in the energy-delay space. To do so, first we define the procedures to obtain energy consumption and propagation delay by simulating a ripple carry adder designed at a transistor level. Then, we introduce a design methodology to optimize a ripple carry adder by minimizing some significant figures-of-merit in terms of energy-delay trade-offs. The comparison of the energy-efficient curves allows us to make a simple and effective comparison as well as to identify the best one-bit full adder topologies.
- Open Access
- 16 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 99702-99708
A Novel Clock Gating Approach for the Design of Low-Power Linear Feedback Shift Registers
This paper presents an efficient solution to reduce the power consumption of the popular linear feedback shift register by exploiting the gated clock approach. The power reduction with respect to other gated clock schemes is obtained by an efficient implementation of the logic gates and properly reducing the number of XOR gates in the feedback network. Transistor level simulations are performed by using standard cells in a 28-nm FD-SOI CMOS technology and a 300-MHz clock. Simulation results show a power reduction with respect to traditional implementations, which reaches values higher than 30%.
- 16 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 99702-99708
Open AccessA Novel Clock Gating Approach for the Design of Low-Power Linear Feedback Shift Registers
This paper presents an efficient solution to reduce the power consumption of the popular linear feedback shift register by exploiting the gated clock approach. The power reduction with respect to other gated clock schemes is obtained by an efficient implementation of the logic gates and properly reducing the number of XOR gates in the feedback network. Transistor level simulations are performed by using standard cells in a 28-nm FD-SOI CMOS technology and a 300-MHz clock. Simulation results show a power reduction with respect to traditional implementations, which reaches values higher than 30%.
- Open Access
- 18 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 75482-75494
Analysis and Comparison in the Energy-Delay Space of Nanometer CMOS One-Bit Full-Adders
In this paper we analyze, design and compare six significant topologies of one-bit full adders in terms of their Energy-Efficient Curves in the Energy-Delay Space.We define the simulation strategies that are adopted to make a fair comparison even among cells with very different characteristics. Each topology is designed through a methodology which, thanks to the adoption of a circuit optimizer, allows to design the circuit under different energy-delay trade-offs and to derive the Energy-Efficient Curves. The comparison of the topologies is made using a 28 nm CMOS technology in terms of normalized Energy-Efficient Curves. In particular, plotting all these Energy-Efficient Curves in a single graph makes the comparison very effective and allows the designer to choose the best topology or discard the worst ones, at a glance.
- 18 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 75482-75494
Open AccessAnalysis and Comparison in the Energy-Delay Space of Nanometer CMOS One-Bit Full-Adders
In this paper we analyze, design and compare six significant topologies of one-bit full adders in terms of their Energy-Efficient Curves in the Energy-Delay Space.We define the simulation strategies that are adopted to make a fair comparison even among cells with very different characteristics. Each topology is designed through a methodology which, thanks to the adoption of a circuit optimizer, allows to design the circuit under different energy-delay trade-offs and to derive the Energy-Efficient Curves. The comparison of the topologies is made using a 28 nm CMOS technology in terms of normalized Energy-Efficient Curves. In particular, plotting all these Energy-Efficient Curves in a single graph makes the comparison very effective and allows the designer to choose the best topology or discard the worst ones, at a glance.
- Open Access
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 25892-25900
A Biasing Approach to Design Ultra-Low-Power Standard-Cell-Based Analog Building Blocks for Nanometer SoCs
This paper presents an approach to design analog building blocks for nanometer systems on a chip (SoCs) that are based on digital standard cells. The proposed approach guarantees that all the CMOS inverters, taken from a standard-cell library, operate with well-defined quiescent current and output voltage, thus allowing the implementation of analog circuits with good robustness against PVT variations. The approach is based on an Analog Body Bias Generator (ABBG) reusable block, similar to the ones adopted in digital applications to cope with process variations, and exploits the bulk terminals of both the p-channel and n-channel MOS transistors of the standard-cell inverter as current and voltage control inputs. The bulk voltages generated by the ABBG are routed to all the standard-cell inverters used for analog functions and allow to set the quiescent current of each cell to a multiple of a reference current and the static output voltage of each cell to half the supply voltage. The full custom design of the ABBG is presented, as well as the design flow to allow the automatic place and route of the proposed standard-cell based analog building blocks. We finally give an example of application to the design of a fully synthesizable four-stage-gain low-power operational transconductance amplifier (OTA). Both the body bias generator and the OTA have been implemented in a 65-nm CMOS technology. The OTA nominal current consumption is 1.75 μA with 0.41-μA standard deviation. Good robustness against supply and temperature variations is also found.
- 4 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 25892-25900
Open AccessA Biasing Approach to Design Ultra-Low-Power Standard-Cell-Based Analog Building Blocks for Nanometer SoCs
This paper presents an approach to design analog building blocks for nanometer systems on a chip (SoCs) that are based on digital standard cells. The proposed approach guarantees that all the CMOS inverters, taken from a standard-cell library, operate with well-defined quiescent current and output voltage, thus allowing the implementation of analog circuits with good robustness against PVT variations. The approach is based on an Analog Body Bias Generator (ABBG) reusable block, similar to the ones adopted in digital applications to cope with process variations, and exploits the bulk terminals of both the p-channel and n-channel MOS transistors of the standard-cell inverter as current and voltage control inputs. The bulk voltages generated by the ABBG are routed to all the standard-cell inverters used for analog functions and allow to set the quiescent current of each cell to a multiple of a reference current and the static output voltage of each cell to half the supply voltage. The full custom design of the ABBG is presented, as well as the design flow to allow the automatic place and route of the proposed standard-cell based analog building blocks. We finally give an example of application to the design of a fully synthesizable four-stage-gain low-power operational transconductance amplifier (OTA). Both the body bias generator and the OTA have been implemented in a 65-nm CMOS technology. The OTA nominal current consumption is 1.75 μA with 0.41-μA standard deviation. Good robustness against supply and temperature variations is also found.
- Open Access
- 27 June 2021
- Published by MDPI AG in Electronics
- Vol. 10 (13) , 1551
Behavioral Model of Silicon Photo-Multipliers Suitable for Transistor-Level Circuit Simulation
Silicon Photomultipliers (SiPMs) are photo-electronic devices able to detect single photons and permit the measurement of weak optical signals. Single-photon detection is accomplished through high-performance read-out front-end electronics whose design needs accurate modeling of the photomultiplier device. In the past, a useful model was developed, but it is limited to the device electrical characteristic and its parameter extraction procedure requires several measurement steps. A new silicon photomultiplier model is proposed in this paper. It exploits the Verilog-a behavioral language and is appropriate to transistor-level circuit simulations. The photon detection of a single cell is modeled using the traditional electrical model. A statistical model is included to describe the silicon photomultiplier noise caused by dark-count or after-pulsing effects. The paper also includes a procedure for the extraction of the model parameters through measurements. The Verilog-a model and the extraction procedure are validated by comparing simulations to experimental results.
- 27 June 2021
- Published by MDPI AG in Electronics
- Vol. 10 (13) , 1551
Open AccessBehavioral Model of Silicon Photo-Multipliers Suitable for Transistor-Level Circuit Simulation
Silicon Photomultipliers (SiPMs) are photo-electronic devices able to detect single photons and permit the measurement of weak optical signals. Single-photon detection is accomplished through high-performance read-out front-end electronics whose design needs accurate modeling of the photomultiplier device. In the past, a useful model was developed, but it is limited to the device electrical characteristic and its parameter extraction procedure requires several measurement steps. A new silicon photomultiplier model is proposed in this paper. It exploits the Verilog-a behavioral language and is appropriate to transistor-level circuit simulations. The photon detection of a single cell is modeled using the traditional electrical model. A statistical model is included to describe the silicon photomultiplier noise caused by dark-count or after-pulsing effects. The paper also includes a procedure for the extraction of the model parameters through measurements. The Verilog-a model and the extraction procedure are validated by comparing simulations to experimental results.
- Open Access
- 12 May 2021
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 11 (2) , 21
A gm/ID-Based Design Strategy for IoT and Ultra-Low-Power OTAs with Fast-Settling and Large Capacitive Loads
In this paper, a new strategy for the design of ultra-low-power CMOS operational transconductance amplifiers (OTAs), using the approach, is proposed for the Internet-of-things (IoT) scenario. The strategy optimizes the speed/dissipation of the OTA in terms of settling time, including slew-rate effects. It was designed for large capacitive loads and for transistors biased in the sub-threshold region, but it is also suitable for low-capacitive loads or for transistors biased in the saturation region. To validate the proposed strategy, a well-known three-stage OTA was designed starting from capacitive load and settling time requirements. Simulations confirmed that the OTA satisfies the specifications (even under Monte Carlo analysis), thus proving the correctness of the proposed approach.- 12 May 2021
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 11 (2) , 21
Open AccessA gm/ID-Based Design Strategy for IoT and Ultra-Low-Power OTAs with Fast-Settling and Large Capacitive Loads
In this paper, a new strategy for the design of ultra-low-power CMOS operational transconductance amplifiers (OTAs), using the approach, is proposed for the Internet-of-things (IoT) scenario. The strategy optimizes the speed/dissipation of the OTA in terms of settling time, including slew-rate effects. It was designed for large capacitive loads and for transistors biased in the sub-threshold region, but it is also suitable for low-capacitive loads or for transistors biased in the saturation region. To validate the proposed strategy, a well-known three-stage OTA was designed starting from capacitive load and settling time requirements. Simulations confirmed that the OTA satisfies the specifications (even under Monte Carlo analysis), thus proving the correctness of the proposed approach.