Nobuaki Otsuki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nobuaki Otsuki has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
Tsuyoshi Saito
Faculty of Engineering, Dept. of Civil Engineering and Architecture, Niigata University, Niigata-shi, Japan
12 shared publicationsTakahiro Nishida
Graduate School of Sci. and Eng., Tokyo Inst. of Tech
9 shared publicationsMakoto Hisada
7 shared publicationsJae-Suk Ryu
6 shared publicationsShigeyoshi Nagataki
6 shared publicationsShin-Ichi Miyazato
Kanazawa Institute of Technology, Hakusan, Ishikawa Prefecture, Japan
6 shared publications
Latest Publications
- Open Access
- 24 July 2014
- Published by Purdue University Press
- p. 393-402
Development of Improved Electrodeposition Method for Repair of Reinforced Concrete Structures
Deterioration of reinforced concrete members and their repair methods have been reported in various concrete published reports. Electrodeposition method is one of these repair methods for repairing deteriorated concrete members using an electrochemical mechanism. The purposes of the electrodeposition method are to fill cracks in concrete and to coat the concrete surface by electrodeposits of chemical compounds. This can be accomplished by passing a weak direct current (1.0–3.0 A/m2 of concrete surface area) between a reinforcing steel bar (cathode) in concrete and an external electrode (anode) located in an external solution near the concrete surface. This method also accomplishes corrosion protection and desalination/re-alkalization, as well as crack closure or surface coating by the electrodeposits. Therefore, it is considered that the electrodeposition is effective in repairing deteriorated concrete members because of chloride attack or carbonation. However, there is very little work on the selection of appropriate electrodeposition conditions such as the type of the cation, its concentration, or type of external electrode for repairing existing reinforced concretes. Therefore, the objective of this paper is to investigate the electrodeposition conditions such as external solution or an external electrode for repairing reinforced concrete structures. From this study, the most suitable electrodeposition conditions to repair deteriorated concrete members are found to be a magnesium acetate-based external solution and an aluminum sacrificial electrode.
- 24 July 2014
- Published by Purdue University Press
- p. 393-402
Open AccessDevelopment of Improved Electrodeposition Method for Repair of Reinforced Concrete Structures
Deterioration of reinforced concrete members and their repair methods have been reported in various concrete published reports. Electrodeposition method is one of these repair methods for repairing deteriorated concrete members using an electrochemical mechanism. The purposes of the electrodeposition method are to fill cracks in concrete and to coat the concrete surface by electrodeposits of chemical compounds. This can be accomplished by passing a weak direct current (1.0–3.0 A/m2 of concrete surface area) between a reinforcing steel bar (cathode) in concrete and an external electrode (anode) located in an external solution near the concrete surface. This method also accomplishes corrosion protection and desalination/re-alkalization, as well as crack closure or surface coating by the electrodeposits. Therefore, it is considered that the electrodeposition is effective in repairing deteriorated concrete members because of chloride attack or carbonation. However, there is very little work on the selection of appropriate electrodeposition conditions such as the type of the cation, its concentration, or type of external electrode for repairing existing reinforced concretes. Therefore, the objective of this paper is to investigate the electrodeposition conditions such as external solution or an external electrode for repairing reinforced concrete structures. From this study, the most suitable electrodeposition conditions to repair deteriorated concrete members are found to be a magnesium acetate-based external solution and an aluminum sacrificial electrode.
- 15 August 2013
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 62 (8) , 518-523
Basic Study on Underground Corrosion Properties of Steel
- 15 August 2013
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 62 (8) , 518-523
Basic Study on Underground Corrosion Properties of Steel
- 15 August 2013
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 62 (8) , 510-517
Evaluation of Corrosion around Defect on Paint-Coated Steel
Corrosion of paint-coated steel exposed to marine environment is one of the serious problems and there are many researches related to such corrosion. Also it is recognized that the defect plays very important roles in such corrosion. Nevertheless, there are still few studies about the deterioration progress of paint-coated steel around defect. Therefore, the objective of present study is to clarify the corrosion progress of paint-coated steel around defect based on experimental and mathematical approach. In the experiments, accelerated test simulating the sub-tidal zone was conducted to observe the macrocell corrosion behavior as well as microcell corrosion. Here, temperature of the solution was changed as parameter in order to clarify the influence of temperature on corrosion rate. Also a mathematical model for calculation of the macrocell corrosion current around defect was proposed. The conclusions derived from present study were as follows. (1) Anodic current of macrocell corrosion at defect parts and its cathodic current at paint-coated parts increased, as time passed. After much cathodic reaction of macrocell corrosion occurred on steel plate under paint-coating, the coating was blistered and/or ripped, and then microcell corrosion current increasingly occurred there. (2) The higher corrosion current observed with temperature elevation. Also it was estimated that the diffusion of oxygen or Fe2+ controlled the corrosion current after coating's degradation based on the activation energy obtained in present study. (3) A mathematical model for macrocell corrosion current was proposed and the trends of the model agreed with experimental data.
- 15 August 2013
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 62 (8) , 510-517
Evaluation of Corrosion around Defect on Paint-Coated Steel
Corrosion of paint-coated steel exposed to marine environment is one of the serious problems and there are many researches related to such corrosion. Also it is recognized that the defect plays very important roles in such corrosion. Nevertheless, there are still few studies about the deterioration progress of paint-coated steel around defect. Therefore, the objective of present study is to clarify the corrosion progress of paint-coated steel around defect based on experimental and mathematical approach. In the experiments, accelerated test simulating the sub-tidal zone was conducted to observe the macrocell corrosion behavior as well as microcell corrosion. Here, temperature of the solution was changed as parameter in order to clarify the influence of temperature on corrosion rate. Also a mathematical model for calculation of the macrocell corrosion current around defect was proposed. The conclusions derived from present study were as follows. (1) Anodic current of macrocell corrosion at defect parts and its cathodic current at paint-coated parts increased, as time passed. After much cathodic reaction of macrocell corrosion occurred on steel plate under paint-coating, the coating was blistered and/or ripped, and then microcell corrosion current increasingly occurred there. (2) The higher corrosion current observed with temperature elevation. Also it was estimated that the diffusion of oxygen or Fe2+ controlled the corrosion current after coating's degradation based on the activation energy obtained in present study. (3) A mathematical model for macrocell corrosion current was proposed and the trends of the model agreed with experimental data.
- 22 March 2013
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 11 (3) , 108-118
Application of Electrical Treatment to Alteration of Cementitious Material due to Leaching
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 22 March 2013
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 11 (3) , 108-118
Application of Electrical Treatment to Alteration of Cementitious Material due to Leaching
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 15 August 2012
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 61 (8) , 736-741
Influence of the Ions in Pore Solution and around the Steel Bar on Corrosion of Steel in BFS and FA Mortars
- 15 August 2012
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 61 (8) , 736-741
Influence of the Ions in Pore Solution and around the Steel Bar on Corrosion of Steel in BFS and FA Mortars
- Open Access
- 15 February 2012
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 61 (2) , 189-196
Influence of Additional Blast Furnace Slag, Anhydrate and Lime Stone Powder and Submerged Temperature on Sulfate Resistance of Ordinary Portland Cement Paste and Mortar
- 15 February 2012
- Published by Society of Materials Science, Japan in Journal of the Society of Materials Science, Japan
- Vol. 61 (2) , 189-196
Open AccessInfluence of Additional Blast Furnace Slag, Anhydrate and Lime Stone Powder and Submerged Temperature on Sulfate Resistance of Ordinary Portland Cement Paste and Mortar
- 24 October 2011
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 9 (3) , 223-230
Permeability of Sulfate Ions in Cementitious Materials Containing γ-Ca2SiO4 after Autoclave Curing and Accelerated Carbonation
- 24 October 2011
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 9 (3) , 223-230
Permeability of Sulfate Ions in Cementitious Materials Containing γ-Ca2SiO4 after Autoclave Curing and Accelerated Carbonation
- 1 January 2011
- Published by Japan Cement Association in Cement Science and Concrete Technology
- Vol. 65 (1) , 168-175
MgSO4 RESISTANCE OF BLAST FURNACE SLAG CEMENT WITH ANHYDRITE AND LIME STONE POWDER, AND MATERIAL DESIGN FOR SULFATE ATTACK
- 1 January 2011
- Published by Japan Cement Association in Cement Science and Concrete Technology
- Vol. 65 (1) , 168-175
MgSO4 RESISTANCE OF BLAST FURNACE SLAG CEMENT WITH ANHYDRITE AND LIME STONE POWDER, AND MATERIAL DESIGN FOR SULFATE ATTACK