Kankat Ghosh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kankat Ghosh has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Apurba Laha
Indian Institute of Technology Bombay
10 shared publications - Balkrishna Choubey
Department of Electrical Engineering, Indian Institute of Technology Jammu, Jammu, India
3 shared publications Ritam Sarkar
Department of Electrical Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India
3 shared publicationsSudipta Das
Indian Inst Technol, Dept Elect Engn, Bombay 400076, Maharashtra, India
3 shared publicationsSwagata Bhunia
Department of Physics, Indian Institute of Technology Bombay, Mumbai 400076, India
3 shared publicationsApurba Laha
2 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 62 (5) , 4000208
Mechanisms Behind Robust and Reliable High-Temperature Current Transport in AlGaN-Based Solar-Blind UV Photodetector
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 62 (5) , 4000208
Mechanisms Behind Robust and Reliable High-Temperature Current Transport in AlGaN-Based Solar-Blind UV Photodetector
- 4 September 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (36) , 365101
EBL-free strategic hybrid MQW with indium-alloyed barriers for efficient green micro-LEDs with reduced operating voltage
Green micro-light emitting diodes (µLEDs) with sub-100 µm dimensions are crucial for next-generation display technologies but remain constrained by the persistent ‘green gap’ and low current density operation challenges. This work numerically investigates optimized epitaxial designs for 60 × 60 µm2 InGaN-based green µLEDs operating at 1 A cm−2, exploring multiple configurations to reveal performance enhancing innovations and their underlying mechanisms. We propose a hybrid multiple quantum well design featuring four step-graded low-indium-content passive quantum wells paired with a single green emitting active QW. This configuration enhances electron–hole wavefunction overlap, suppresses the quantum confined Stark effect, and reduces the active recombination volume. Further performance improvements are achieved by eliminating the electron blocking layer to boost hole injection and introducing indium-alloyed quantum barriers to reduce polarization-induced interface charges. These innovations collectively result in an 18% increase in internal quantum efficiency, a 37% reduction in operating voltage, and a 74% enhancement in wall-plug efficiency compared to the conventional high-indium-content identical 5-QW structure. This simplified final design offers a scalable and cost-effective pathway toward high-efficiency green µLEDs, with implications for broader adoption in full-color micro-displays and long-wavelength III-Nitride emitters.
- 4 September 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (36) , 365101
EBL-free strategic hybrid MQW with indium-alloyed barriers for efficient green micro-LEDs with reduced operating voltage
Green micro-light emitting diodes (µLEDs) with sub-100 µm dimensions are crucial for next-generation display technologies but remain constrained by the persistent ‘green gap’ and low current density operation challenges. This work numerically investigates optimized epitaxial designs for 60 × 60 µm2 InGaN-based green µLEDs operating at 1 A cm−2, exploring multiple configurations to reveal performance enhancing innovations and their underlying mechanisms. We propose a hybrid multiple quantum well design featuring four step-graded low-indium-content passive quantum wells paired with a single green emitting active QW. This configuration enhances electron–hole wavefunction overlap, suppresses the quantum confined Stark effect, and reduces the active recombination volume. Further performance improvements are achieved by eliminating the electron blocking layer to boost hole injection and introducing indium-alloyed quantum barriers to reduce polarization-induced interface charges. These innovations collectively result in an 18% increase in internal quantum efficiency, a 37% reduction in operating voltage, and a 74% enhancement in wall-plug efficiency compared to the conventional high-indium-content identical 5-QW structure. This simplified final design offers a scalable and cost-effective pathway toward high-efficiency green µLEDs, with implications for broader adoption in full-color micro-displays and long-wavelength III-Nitride emitters.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (8) , 4204-4210
Highly Sensitive and Fast Response AlGaN-Based MSM Solar-Blind Photodetector
The aluminum gallium nitride (AlGaN)/AlN/ sapphire-based solar-blind metal–semiconductor–metal (MSM) photodetectors are highly valued for applications that require mechanical and thermal stability under varying environmental conditions due to advantages over bulky and fragile photomultipliers, including lightweight design, low energy consumption, and high durability. Thus, this study demonstrates the critical analysis of the fabrication and characterization of AlGaN-based solar-blind MSM photodetector. The high crystalline quality i.e., average threading dislocation density ~108/cm2 and rms roughness ~621 pm for 2 × 2 μm2 area effectively suppresses the leakage (dark) current to 65.2 × 10-12 A at 5 V. Under 255 nm illumination, the photocurrent reaches to ~4 × 10-6 A at 5 V, which is approximately five orders of magnitude higher than the dark current. The photodetector demonstrates exceptional performance metrics, including the high responsivity of ~13 A/W, ultraviolet to visible rejection ratio of 1.3 × 103, and the detection rate of 3 × 1011 Jones at 5 V, surpassing many recently reported devices. Furthermore, it exhibits an ultrafast temporal response, with rise and fall times of ~24 and ~23 μs, respectively.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (8) , 4204-4210
Highly Sensitive and Fast Response AlGaN-Based MSM Solar-Blind Photodetector
The aluminum gallium nitride (AlGaN)/AlN/ sapphire-based solar-blind metal–semiconductor–metal (MSM) photodetectors are highly valued for applications that require mechanical and thermal stability under varying environmental conditions due to advantages over bulky and fragile photomultipliers, including lightweight design, low energy consumption, and high durability. Thus, this study demonstrates the critical analysis of the fabrication and characterization of AlGaN-based solar-blind MSM photodetector. The high crystalline quality i.e., average threading dislocation density ~108/cm2 and rms roughness ~621 pm for 2 × 2 μm2 area effectively suppresses the leakage (dark) current to 65.2 × 10-12 A at 5 V. Under 255 nm illumination, the photocurrent reaches to ~4 × 10-6 A at 5 V, which is approximately five orders of magnitude higher than the dark current. The photodetector demonstrates exceptional performance metrics, including the high responsivity of ~13 A/W, ultraviolet to visible rejection ratio of 1.3 × 103, and the detection rate of 3 × 1011 Jones at 5 V, surpassing many recently reported devices. Furthermore, it exhibits an ultrafast temporal response, with rise and fall times of ~24 and ~23 μs, respectively.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (12) , 21424-21431
Ultralow Dark Current and High-Speed GaN-Based Visible Blind UV Photodetector
This article presents a critical analysis of the fabrication and characterization of a Gallium Nitride (GaN)-based visible-blind metal-semiconductor-metal (MSM) UV-photodetector. The GaN epilayer exhibits an excellent crystalline quality, as evidenced by symmetric and asymmetric x-ray rocking curve (XRC) full width at half maximum (FWHM) values of ~60 and ~223.2 arcsec, respectively, along with an average threading dislocation density (TDD) in the order of ~107 cm-2 as derived from XRC data. Atomic force microscopy (AFM) analysis reveals a root mean square (RMS) roughness of ~424 pm, further highlighting the smoothness of the epilayer. The high crystalline quality significantly reduces the leakage (dark) current, measured as 3×10−12 A at 15 V, one of the lowest as compared to the already reported devices. The photocurrent with 360 nm input illumination was obtained to be 1.2×10−7 A at 15 V, approximately four orders of magnitude higher than the dark current. The photodetector demonstrates exceptional performance metrics, including a detectivity of 6×1012 Jones and a responsivity of 0.522 A/W at 15 V, surpassing many other recent reports. Also, it features an unmatched ultra-fast temporal response with rise and fall times of ~31 and ~27 μs, respectively, setting a benchmark for high-speed operation.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (12) , 21424-21431
Ultralow Dark Current and High-Speed GaN-Based Visible Blind UV Photodetector
This article presents a critical analysis of the fabrication and characterization of a Gallium Nitride (GaN)-based visible-blind metal-semiconductor-metal (MSM) UV-photodetector. The GaN epilayer exhibits an excellent crystalline quality, as evidenced by symmetric and asymmetric x-ray rocking curve (XRC) full width at half maximum (FWHM) values of ~60 and ~223.2 arcsec, respectively, along with an average threading dislocation density (TDD) in the order of ~107 cm-2 as derived from XRC data. Atomic force microscopy (AFM) analysis reveals a root mean square (RMS) roughness of ~424 pm, further highlighting the smoothness of the epilayer. The high crystalline quality significantly reduces the leakage (dark) current, measured as 3×10−12 A at 15 V, one of the lowest as compared to the already reported devices. The photocurrent with 360 nm input illumination was obtained to be 1.2×10−7 A at 15 V, approximately four orders of magnitude higher than the dark current. The photodetector demonstrates exceptional performance metrics, including a detectivity of 6×1012 Jones and a responsivity of 0.522 A/W at 15 V, surpassing many other recent reports. Also, it features an unmatched ultra-fast temporal response with rise and fall times of ~31 and ~27 μs, respectively, setting a benchmark for high-speed operation.
- 14 October 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (1) , 015113
Enhancing the yellow-LED performance with improvised pre-stress alleviation layer: a theoretical and numerical analysis
The decline in quantum efficiency observed in yellow-LEDs emitting wavelength around ∼575 nm, commonly known as the ‘green-yellow gap’, is predominantly influenced by the fact that high In-content In x Ga1−x N/GaN (x = 30%) yellow-multiple quantum wells (yellow-MQWs) are typically grown on GaN template. This configuration leads to substantial compressive stress, contributing to the structural defects and the significant quantum confined stark effect. To address this challenge, our strategy involves achieving superior lattice constant alignment within the yellow-MQWs by growing a pre-stress alleviation layer (PSAL) prior to the growth of yellow-MQWs. Our comprehensive theoretical study, coupled with numerical simulations, aimed to explore the impact of two distinct practical and commercially viable PSAL approaches: pre-quantum well, comprising short periods of InYGa1−Y N/GaN and pre-thin layer, incorporating a thin layer of In Z Ga1−Z N. Following a thorough analysis of these approaches, we propose an innovative improved optimized structure that demonstrates the highest internal quantum efficiency of 74.2%, minimal efficiency droop of 14.7% at 20 A cm−2, and a 20 nm favourable red-shift in electroluminescence characteristic with narrower full-width-half-maximum of 28 nm without any adverse effect on the pure yellow-color emission at 20 A cm−2. This advancement holds promise for providing better crystal quality and addressing the green-yellow gap issue in yellow-LED technology.
- 14 October 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (1) , 015113
Enhancing the yellow-LED performance with improvised pre-stress alleviation layer: a theoretical and numerical analysis
The decline in quantum efficiency observed in yellow-LEDs emitting wavelength around ∼575 nm, commonly known as the ‘green-yellow gap’, is predominantly influenced by the fact that high In-content In x Ga1−x N/GaN (x = 30%) yellow-multiple quantum wells (yellow-MQWs) are typically grown on GaN template. This configuration leads to substantial compressive stress, contributing to the structural defects and the significant quantum confined stark effect. To address this challenge, our strategy involves achieving superior lattice constant alignment within the yellow-MQWs by growing a pre-stress alleviation layer (PSAL) prior to the growth of yellow-MQWs. Our comprehensive theoretical study, coupled with numerical simulations, aimed to explore the impact of two distinct practical and commercially viable PSAL approaches: pre-quantum well, comprising short periods of InYGa1−Y N/GaN and pre-thin layer, incorporating a thin layer of In Z Ga1−Z N. Following a thorough analysis of these approaches, we propose an innovative improved optimized structure that demonstrates the highest internal quantum efficiency of 74.2%, minimal efficiency droop of 14.7% at 20 A cm−2, and a 20 nm favourable red-shift in electroluminescence characteristic with narrower full-width-half-maximum of 28 nm without any adverse effect on the pure yellow-color emission at 20 A cm−2. This advancement holds promise for providing better crystal quality and addressing the green-yellow gap issue in yellow-LED technology.
- 24 September 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (49) , 495705
Role of defect saturation in improving optical response from InGaN nanowires in higher wavelength regime
Growth of InGaN, having high Indium composition without compromising crystal quality has always been a great challenge to obtain efficient optical devices. In this work, we extensively study the impact of non-radiative defects on optical response of the plasma assisted molecular beam epitaxy (PA-MBE) grown InGaN nanowires, emitting in the higher wavelength regime ( λ > 520 nm). Our analysis focuses into the effect of defect saturation on the optical output, manifested by photoluminescence (PL) spectroscopy. Defect saturation has not so far been thoroughly investigated in InGaN based systems at such a high wavelength, where defects play a key role in restraining efficient optical performance. We argue that with saturation of defect states by photo-generated carriers, the advantages of carrier localization can be employed to enhance the optical output. Carrier localization arises because of Indium phase segregation, which is confirmed from wide PL spectrum and analysis from transmission electron microscopy (TEM). A theoretical model has been proposed and solved using coupled differential rate equations in steady state to undertake different phenomena, occurred during PL measurements. Analysis of the model helps us understand the impact of non-radiative defects on PL response and identifying the origin of enhanced radiative recombination.
- 24 September 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (49) , 495705
Role of defect saturation in improving optical response from InGaN nanowires in higher wavelength regime
Growth of InGaN, having high Indium composition without compromising crystal quality has always been a great challenge to obtain efficient optical devices. In this work, we extensively study the impact of non-radiative defects on optical response of the plasma assisted molecular beam epitaxy (PA-MBE) grown InGaN nanowires, emitting in the higher wavelength regime ( λ > 520 nm). Our analysis focuses into the effect of defect saturation on the optical output, manifested by photoluminescence (PL) spectroscopy. Defect saturation has not so far been thoroughly investigated in InGaN based systems at such a high wavelength, where defects play a key role in restraining efficient optical performance. We argue that with saturation of defect states by photo-generated carriers, the advantages of carrier localization can be employed to enhance the optical output. Carrier localization arises because of Indium phase segregation, which is confirmed from wide PL spectrum and analysis from transmission electron microscopy (TEM). A theoretical model has been proposed and solved using coupled differential rate equations in steady state to undertake different phenomena, occurred during PL measurements. Analysis of the model helps us understand the impact of non-radiative defects on PL response and identifying the origin of enhanced radiative recombination.
- 4 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 105917
Study of surface over-layer contribution to Dislocation Assisted Tunneling current: Strategy to improve Pt/n +–GaN Schottky characteristics
This paper reports the importance of surface over-layer contribution to the dislocation assisted tunneling (DAT) current along with earlier reported bulk dislocations due to growth of GaN layers on highly lattice-mismatched substrates. This claim is substantiated by demonstrating an improved Pt/n+-GaN Schottky diode characteristics with the removal of surface over-layer. This is achieved by treating the n+-GaN layers with Buffered Oxide Etchant (BOE) before Pt deposition. The improvements are observed in three crucial aspects of Pt/n+-GaN Schottky diode namely turn-on voltage (Vt); dislocation assisted tunnelling (DAT) parameter E0, and reverse bias current. These improvements are achieved by treating n+-GaN surface with 1:7 BOE before Pt deposition. The DAT model adequately explains the device characteristics. Further, the dislocation density used in DAT analysis is experimentally quantified using HR-XRD. The removal of Ga2O3 and significant blue shift of Ga 3d peaks by 0.6 eV post-treatment as observed in XPS measurements, results in improved conduction of electrons at the n+−GaN surface and Pt/n+−GaN device characteristics.
- 4 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 105917
Study of surface over-layer contribution to Dislocation Assisted Tunneling current: Strategy to improve Pt/n +–GaN Schottky characteristics
This paper reports the importance of surface over-layer contribution to the dislocation assisted tunneling (DAT) current along with earlier reported bulk dislocations due to growth of GaN layers on highly lattice-mismatched substrates. This claim is substantiated by demonstrating an improved Pt/n+-GaN Schottky diode characteristics with the removal of surface over-layer. This is achieved by treating the n+-GaN layers with Buffered Oxide Etchant (BOE) before Pt deposition. The improvements are observed in three crucial aspects of Pt/n+-GaN Schottky diode namely turn-on voltage (Vt); dislocation assisted tunnelling (DAT) parameter E0, and reverse bias current. These improvements are achieved by treating n+-GaN surface with 1:7 BOE before Pt deposition. The DAT model adequately explains the device characteristics. Further, the dislocation density used in DAT analysis is experimentally quantified using HR-XRD. The removal of Ga2O3 and significant blue shift of Ga 3d peaks by 0.6 eV post-treatment as observed in XPS measurements, results in improved conduction of electrons at the n+−GaN surface and Pt/n+−GaN device characteristics.