JYJyh-Cheng Yu

Jyh-Cheng Yu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jyh-Cheng Yu has a total of 48 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Novel design of a coreless axial‐flux permanent‐magnet generator with three‐layer winding coil for small wind turbines

    by Wu‐Sung Yao, Ming‐Te Cheng, Jyh‐Cheng Yu

    This study presents a novel design of the three‐layer winding coil sets of a coreless axial‐flux permanent‐magnet generator applied to small wind turbines. The proposed generator design consists of two rotors and an integrated stator with flattened winding coil sets of three‐phase three layers connected using a wye configuration. An analytical model of the inductance and resistance of the coil set is described to analyse the influence of the coil shape variation due to winding imperfection. The air gap magnetic flux distribution analysis shows the advantage of the integrated flatten coil sets compared with a typical stack up three layers stator. An experimental design is conducted for the parameter design of geometric variables to optimise the output power of the proposed axial‐flux permanent‐magnet design. A prototype generator is then constructed to compare with a benchmark generator that has a rated output power of 300 W at 800 rpm. The proposed design outperforms the benchmark generator by 26.5% in terms of generated power at a typical driving rotation velocity of 500 rpm for a small wind turbine, and demonstrates a superior performance at a lower driving speed range, which is particularly important in a small wind turbine application.


  • Open Access

    Optimum Design of Microridge Deep Drawing Punch Using Regional Kriging Assisted Fuzzy Multiobjective Evolutionary Algorithm

    by Suprayitno, Cheng-Yu Yang, Jyh-Cheng Yu, Bor-Tsuen Lin

    This study introduces an optimized microridge-punch design for deep-drawing processes with improved formability and punch service life. Reducing the thickness of metal sheets results in a marked decrease in the microscale/mesoscale deep drawing rates. Prior studies have recognized that the drawing punch with a microridge design next to the punch nose lowers the thinning rate and improves the deep-drawing formability. However, the increased stripping force associated with the microridge design may result in deformation of the drawn cup and shorten the punch service life. Here we present a parameter optimization of the microridge design in which there is a trade-off between multiple objectives in the deep-drawing process. We introduce a fuzzy inference to synthesize two design objectives, i.e., the thinning rate and stripping force, into single design fitness. We use Deform-2D software to simulate deep-drawing performance for design optimization. Since the simulation of design objectives is computationally expensive, we introduce a novel sequential surrogate-based optimization to improve the sampling and searching efficiencies. The proposed optimal microridge design outperforms the best design for both the thinning rate and stripping force of all the samples, as well as the design obtained by the Taguchi method based on the fuzzy design fitness. Compared with the Taguchi design, the proposed optimum design improves the fuzzy design fitness by 29.2%, whereby the stripping force is significantly reduced by 35.2%, with only a slight 2% increase in the thinning rate. The proposed design effectively ensures both the deep drawing formability and the microridge-punch service life.


  • Evolutionary reliable regional Kriging surrogate for expensive optimization

    by Suprayitno, Jyh-Cheng Yu

    This work proposes a sequential optimization algorithm, EORKS, combining a Kriging surrogate from an adaptive sampling and an iterative constrained search in the dynamic reliable regions to reduce the sampling size in expensive optimization. A surrogate established from small samples is liable to limited generality, which leads to a false prediction of optimum. EORKS applies Kriging variance to establish the reliable region neighbouring the learning samples to constrain the evolutionary searches of the surrogate. The verified quasi-optimum is used as an additional sample to dynamically update the regional model according to the prediction accuracy. A hybrid infilling strategy switches between the iterative quasi-optima and the maximum expected improvement from Kriging to prevent early convergence of local optimum. EORKS provides superior optima in several benchmark functions and an engineering design problem, using much smaller samples compared with the literature results, which demonstrates the sampling efficiency and searching robustness.


  • Open Access

    Evolutionary Reliable Regional Kriging Surrogate and Soft Outer Array for Robust Engineering Optimization

    by Jyh-Cheng Yu, Suprayitno

    Robust optimization seeks designs with optimized performance and low sensitivity to possible variations in a product's life-cycle. As a popular robust design scheme in industry, Taguchi method uses the signal-to-noise ratio (SNR) as a metric of robustness. However, the Taguchi experimental design includes an inner orthogonal arrays (OA) for control factors and an outer OA for noise factors in estimating SNR-based robustness, raising a serious cost concern, especially if expensive samples are involved. Furthermore, rigorous control of noise factors to prespecified levels in the outer OA is impractical in engineering applications. This paper presents a novel approach, robust optimization using evolving reliable Kriging surrogate (ROERKS) that uses an evolving surrogate model to approximate the actual system, and uses a soft outer array to estimate the robustness. Both control variables and noise factors are merged into a combined experimental design served as the training samples to construct a Kriging-based surrogate model. An evolutionary optimizer is applied to search of the subspace of the design variables for a robust optimal solution, and a soft outer array is introduced to estimate the fitness function consisted of the mean and the variance response of evolving individual. To accommodate reduced accuracy of the surrogate model owing to an inadequate sample size, an issue that commonly arises in expensive optimization, the proposed algorithm uses a reliable region to constrain the genetic algorithm search. The verification result of the quasi-optimum is then added to the training samples to refine the evolving surrogate and to adjust the reliable region. A hybrid infilling strategy is then introduced to prevent the early convergence of the quasi-optimum. If the predicted optimum is in close proximity to current samples, the infilling strategy switches to an alternative sample with maximum expected improvement to improve sample efficiency. The iteration process continues until it converges to a robust optimum. The robust optimization of a numerical example for minimization and the robust optimization of a micro accelerometer design with a nominal-the-best sensitivity are presented to demonstrate the effectiveness of the proposed method. ROERKS outperforms Taguchi method and the RSM-based robust optimization, and derives a superior robust optimum using many fewer experiments.


  • Robust design optimisation via surrogate network model and soft outer array design

    by Jyh-Cheng Yu, Chaio-Kai Chang, Suprayitno

    Robust design searches for a performance optimum with least sensitivity to variable and parameter variations. Taguchi method applies an inner array for control factors and an outer array for noise factors to estimate the Signal-to-Noise ratio (S/N). However, the cross product arrays impose serious cost concerns for expensive samplings. Also, rigorous control of noise factors to pre-set levels is impractical in industrial applications. This study presents a soft computing-based robust optimisation that merges control and noise factors into a combined experimental design to establish a surrogate using artificial neural network. Genetic algorithm is applied to search in the sub-space of control factors in the surrogate with a soft outer array to estimate the S/N served as the evolution fitness. Performance variations due to the tolerances of control and uncontrollable factors can then be estimated without conducting actual experiments. The verifications of the predicted optima become additional learning samples to refine the surrogate, and the iteration continues until convergence. The robust optimisation of a micro-accelerometer with maximised gain is used as an illustrative example. The proposed algorithm provides a superior robust optimum using a much smaller sample and less controlling cost compared with Taguchi method and a conventional response surface method.


  • Evolutionary algorithm using progressive Kriging model and dynamic reliable region for expensive optimization problems

    by Suprayitno, Jyh-Cheng Yu

    Surrogate based optimization provides an efficient approach for expensive optimization requiring either costly experiments or time consuming simulations. However, a “good” surrogate model requires lots of training data which is impractical in applications. This work proposes an evolving algorithm, POSER, combining a progressive Kriging model and a constrained search in the dynamic reliable regions to reduce the experiments/function calls required in optimum search. The proposed algorithm starts from a Kriging model from a small sample size and improves progressively using sequential infilling samples, which often has limited generality. In general, the prediction accuracy is worse for a design farther away from the training samples. The prediction error of the Kriging model is applied to establish the reliable region to guide the evolutionary searches in the neighboring region of samples for a quasi-optimum. A hybrid infilling strategy switches between exploitation and exploration to improve sample efficiency. The reliable regional surrogate evolves and refines at the most promising regions of optimum. The process iterates until the convergence of optimum. Optimization of two benchmark numerical functions and an engineering case study are shown and compared with previous literatures. The proposed algorithm outperforms the literature results with a much smaller sample, which demonstrates the robustness and efficiency in the future applications of expensive optimization.


  • Optical design and optimization of planar curved LED end-lit light bar

    by Jyh-Cheng Yu, Zhi-Yao Chen, Bang-De Kao

    This study investigates the optical design of planar curved LED end-lit light bars using v cuts as light-diverting structures. The application of LEDs in automotive lighting has become popular, especially in signal lamps and daytime running lamps. Most designs adopt a direct back light using arrays of LEDs with diffusive coupling optics, which often causes problems such as low uniformity, glaring, and excessive LEDs. Edge-lit LED light guides in automotive applications share a similar principle with the light-guide plates in back-light models of LCD but with much more complicated geometry. However, related literature on the optical design of nonrectangular light-guide plates is very limited. This study addresses the design of planar curved LED end-lit light bars and the optimization scheme for illuminance uniformity. V cuts are used as the optical coupling features, and the lead angles of the v cuts are varied to achieve optimum axial luminous intensity. This study presents a solution to reduce the illuminance difference between the inner and the outer portions of curved light bars by introducing gradual taper v cuts across the curved section. A line graph with preselected anchor points is proposed to define the size distribution of evenly spaced v cuts along the light bar. A fuzzy optimization scheme is then applied to iterate the anchor size to achieve illuminance uniformity. The designs of a planar curve light bar with a rectangular cross section and a light-guide ring with a circular cross section are presented to illustrate the design scheme.


  • Evolutionary regional network modeling for efficient engineering optimization

    by Jyh-Cheng Yu, Zhi-Fu Liang, Tsung-Ren Hung

    This study presents a soft computing based optimization methodology, the evolutionary regional neural network modeling for engineering applications with sampling constraints. Engineering optimization often involves expensive experiment costs. Intelligent optimization advocates establishing a neural network model using small training samples such as orthogonal array to set up a surrogate model for the engineering system followed by an optimum search in the model to reduce optimization cost. However, scarce training samples might compromise modeling generality for a complex problem. Empirical rules suggest reliable predictions are likely restricted to the neighboring space of training samples, and interpolating designs are more reliable than extrapolating designs. To avoid imperfection of model due to small learning samples, an evolutionary regional network model is set up to confine the search of quasi-optimum using genetic algorithm. The constrained search in the regional network model provides a reliable quasi-optimum. The verification of the optimum is added to the learning samples to retrain the regional network model while the size and the distribution of reliable space will evolve intelligently during the optimization iteration using a fuzzy inference according to the prediction accuracy. An engineering case study, the optimal die gap parison programming of extrusion blow molding process for a uniform thickness, is presented to demonstrate the robustness and efficiency of the proposed methodology.


  • Design of LED edge-lit light bar for automotive taillight applications

    by Jyh-Cheng Yu, Jia-Hao Chen, Shih-Chiang Liu