Monoj Kumar Singha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Monoj Kumar Singha has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Aniket Patra
Electrical and Communication Engineering, Indian Institute of Science, Bangalore, India
4 shared publications Kaustab Ghosh
4 shared publicationsSabina Rahaman
4 shared publicationsK. G. Deepa
Department of Physics, University of Kerala, Thiruvananthapuram, India
3 shared publicationsVineet Rojwal
Instrumentation and applied physics, Indian Institute of Science, Bangalore, INDIA
3 shared publicationsKrishna Prakash
2 shared publications
Latest Publications
- 15 November 2024
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 698
Optimization of CTS thin film solar cell: A numerical investigation based on USP deposited thin films
- 15 November 2024
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 698
Optimization of CTS thin film solar cell: A numerical investigation based on USP deposited thin films
- 27 September 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (10) , 105571
Stable RbCsFAPbI3 perovskite solar cell: numerical modelling and optimisation using SCAPS-1D
The studies concerning solar cell technology has consistently been captivating and inspiring, largely because of its environmentally friendly and sustainable characteristics. The outstanding electronic, optical, mechanical, and electrical characteristics of perovskite materials make them crucial for the development of the photovoltaic industry. In order to model the mixed cation Rb0.05Cs0.1FA0.85PbI3 perovskite solar cells, the SCAPS-1D tool was used. The main feature of RbCsFAPbI3 perovskite is its remarkable stability, and wide bandgap. Rubidium (Rb) and cesium (Cs) cations improve the optoelectronic characteristics of the material, resulting in less non-radiative recombination and improved charge transfer. In this work, the effects of different hole transport layers (CuSCN, CuSbS2,Cu2O) and back metal contacts (Ag, Fe, C-Cu, Au, Ni, Pt) on solar cell performance were investigated. The maximum efficiency of the solar cell has been achieved by studying various parameters like temperature, series resistance, shunt resistance, defect density, and absorber layer thickness. With FF = 84.12%, Jsc = 24.52 mA cm−2, Voc = 1.19 V, and the configuration of FTO/TiO2/RbCsFAPbI3/Cu2O/Au, the optimised device obtains a PCE of 24.64%. The impressive enhancements in performance parameters observed in the structure of the device make it highly suitable for applications in solar energy harvesting systems.
- 27 September 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (10) , 105571
Stable RbCsFAPbI3 perovskite solar cell: numerical modelling and optimisation using SCAPS-1D
The studies concerning solar cell technology has consistently been captivating and inspiring, largely because of its environmentally friendly and sustainable characteristics. The outstanding electronic, optical, mechanical, and electrical characteristics of perovskite materials make them crucial for the development of the photovoltaic industry. In order to model the mixed cation Rb0.05Cs0.1FA0.85PbI3 perovskite solar cells, the SCAPS-1D tool was used. The main feature of RbCsFAPbI3 perovskite is its remarkable stability, and wide bandgap. Rubidium (Rb) and cesium (Cs) cations improve the optoelectronic characteristics of the material, resulting in less non-radiative recombination and improved charge transfer. In this work, the effects of different hole transport layers (CuSCN, CuSbS2,Cu2O) and back metal contacts (Ag, Fe, C-Cu, Au, Ni, Pt) on solar cell performance were investigated. The maximum efficiency of the solar cell has been achieved by studying various parameters like temperature, series resistance, shunt resistance, defect density, and absorber layer thickness. With FF = 84.12%, Jsc = 24.52 mA cm−2, Voc = 1.19 V, and the configuration of FTO/TiO2/RbCsFAPbI3/Cu2O/Au, the optimised device obtains a PCE of 24.64%. The impressive enhancements in performance parameters observed in the structure of the device make it highly suitable for applications in solar energy harvesting systems.
- Open Access
- 1 April 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (4) , 045506
Numerical investigation of CuSbS2 thin film solar cell using SCAPS-1D: enhancement of efficiency on experimental films by defect studies
The study of photovoltaic solar cells has been an exciting field of research because of their environmentally friendly nature. Scientists are continuously searching for new methods to develop solar cells that are highly efficient and cost-effective. One promising option is the use of Copper Antimony Sulphide (CuSbS2) based ternary compound semiconductor in ultrathin film photovoltaic cells. This material has a high absorption coefficient, low cost, and is readily available in the earth’s crust. These characteristics make it an ideal candidate for use as a thin-film absorber layer in solar cells. In this work, FTO/CdS/In2S3/CuSbS2/Spiro-OMeTAD/Au device is proposed to improve the efficiency of experimentally designed CuSbS2-based thin film solar cells using numerical modeling. Device simulation was carried out using SCAPS-1D software, and the illumination spectrum used for this optimization was 1.5 AM. The simulated results from SCAPS-1D were compared to the experimental data. After optimizing the device parameters all the electrical parameters of the solar cell were improved. The optimized CuSbS2-based device shows power conversion efficiency (PCE) of 21.11% with short circuit current density (Jsc) of 20.96 mA cm−2, open circuit voltage (Voc) of 1.23 V, and fill factor (FF) of 81.84%. Based on the simulation results, it is possible to increase the performance of the device by varying different parameters such as the defect density of each layer, interfacial defect density, thickness, and doping concentration.
- 1 April 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (4) , 045506
Open AccessNumerical investigation of CuSbS2 thin film solar cell using SCAPS-1D: enhancement of efficiency on experimental films by defect studies
The study of photovoltaic solar cells has been an exciting field of research because of their environmentally friendly nature. Scientists are continuously searching for new methods to develop solar cells that are highly efficient and cost-effective. One promising option is the use of Copper Antimony Sulphide (CuSbS2) based ternary compound semiconductor in ultrathin film photovoltaic cells. This material has a high absorption coefficient, low cost, and is readily available in the earth’s crust. These characteristics make it an ideal candidate for use as a thin-film absorber layer in solar cells. In this work, FTO/CdS/In2S3/CuSbS2/Spiro-OMeTAD/Au device is proposed to improve the efficiency of experimentally designed CuSbS2-based thin film solar cells using numerical modeling. Device simulation was carried out using SCAPS-1D software, and the illumination spectrum used for this optimization was 1.5 AM. The simulated results from SCAPS-1D were compared to the experimental data. After optimizing the device parameters all the electrical parameters of the solar cell were improved. The optimized CuSbS2-based device shows power conversion efficiency (PCE) of 21.11% with short circuit current density (Jsc) of 20.96 mA cm−2, open circuit voltage (Voc) of 1.23 V, and fill factor (FF) of 81.84%. Based on the simulation results, it is possible to increase the performance of the device by varying different parameters such as the defect density of each layer, interfacial defect density, thickness, and doping concentration.
- 21 February 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 316
NiFe2O4 nanoparticles as highly efficient catalyst for oxygen reduction reaction and energy storage in supercapacitor
- 21 February 2024
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 316
NiFe2O4 nanoparticles as highly efficient catalyst for oxygen reduction reaction and energy storage in supercapacitor
- Open Access
- 2 May 2023
- Published by Elsevier in Results in Optics
- Vol. 12
Numerical simulation and optimization of lead free CH3NH3SnI3 perovskite solar cell with CuSbS2 as HTL using SCAPS 1D
- 2 May 2023
- Published by Elsevier in Results in Optics
- Vol. 12
Open AccessNumerical simulation and optimization of lead free CH3NH3SnI3 perovskite solar cell with CuSbS2 as HTL using SCAPS 1D
- 22 March 2023
- Published by Elsevier in Microelectronics Journal
- Vol. 135, 105759
Impact of annealing on structural and optical properties of ZnO thin films
- 22 March 2023
- Published by Elsevier in Microelectronics Journal
- Vol. 135, 105759
Impact of annealing on structural and optical properties of ZnO thin films
- 1 January 2022
- Published by Elsevier in Optical Materials
- Vol. 123
Optimization and fabrication of low cost Cu2SnS3/ZnS thin film heterojunction solar cell using ultrasonic spray pyrolysis
- 1 January 2022
- Published by Elsevier in Optical Materials
- Vol. 123
Optimization and fabrication of low cost Cu2SnS3/ZnS thin film heterojunction solar cell using ultrasonic spray pyrolysis
- 13 December 2021
- Published by Springer Nature in Applied Physics A
- Vol. 128 (1) , 1-10
Nanoarchitectonics earth-abundant chalcogenide Cu2SnS3 thin film using ultrasonic spray pyrolysis for visible light-driven photocatalysis
- 13 December 2021
- Published by Springer Nature in Applied Physics A
- Vol. 128 (1) , 1-10
Nanoarchitectonics earth-abundant chalcogenide Cu2SnS3 thin film using ultrasonic spray pyrolysis for visible light-driven photocatalysis
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (3) , 2627-2633
Amorphous Silicon and Carbon Nanotubes Layered Thin-Film Based Device for Temperature Sensing Application
This paper proposes an integrated layered doped and undoped amorphous silicon thin-film based temperature sensing device. Temperature sensing performance has been measured for thin film p-i-n (p-type- intrinsic- n-type) configuration-based diode. Linear dependency of voltage on the temperature for forward-biased diode at a constant bias current is demonstrated in the temperature range of 30 - 200 °C. Further, the same device has been introduced with double-walled carbon nanotubes (DWCNTs) to improve the linearity of the sensor. Comparative performance of two configurations p-i-n and p-i-n/DWCNTs for temperature sensing application has been studied. Moreover, this paper discussed the effect of the DWCNTs on the sensor parameters such as sensitivity, S and coefficient of determination, R2. The maximum sensitivity of the sensor, 22.34 mV/ °C for p-i-n configured device and 21.06 mV/ °C for p-i-n/DWCNTs configuration in a biasing current range of 10- 60 mA have been found. We achieved a maximum value of the coefficient of determination equal to 0.99889 for a p-i-n configuration and 0.99922 for a p-i-n/ DWCNTs configured device.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (3) , 2627-2633
Amorphous Silicon and Carbon Nanotubes Layered Thin-Film Based Device for Temperature Sensing Application
This paper proposes an integrated layered doped and undoped amorphous silicon thin-film based temperature sensing device. Temperature sensing performance has been measured for thin film p-i-n (p-type- intrinsic- n-type) configuration-based diode. Linear dependency of voltage on the temperature for forward-biased diode at a constant bias current is demonstrated in the temperature range of 30 - 200 °C. Further, the same device has been introduced with double-walled carbon nanotubes (DWCNTs) to improve the linearity of the sensor. Comparative performance of two configurations p-i-n and p-i-n/DWCNTs for temperature sensing application has been studied. Moreover, this paper discussed the effect of the DWCNTs on the sensor parameters such as sensitivity, S and coefficient of determination, R2. The maximum sensitivity of the sensor, 22.34 mV/ °C for p-i-n configured device and 21.06 mV/ °C for p-i-n/DWCNTs configuration in a biasing current range of 10- 60 mA have been found. We achieved a maximum value of the coefficient of determination equal to 0.99889 for a p-i-n configuration and 0.99922 for a p-i-n/ DWCNTs configured device.