Navadol Laosiripojana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Navadol Laosiripojana has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Suttichai Assabumrungrat
Center of Excellence in Catalysis and Catalytic Reaction Engineering, Department of Chemical Engineering, Faculty of Engineering Chulalongkorn University Bangkok Thailand
4 shared publications - Unalome Wetwatana Hartley
Chemical and Process Engineering, The Sirindhorn International Thai-German Graduate School of Engineering (TGGS), King Mongkut's University of Technology North Bangkok, Bangkok, 10800, Thailand
4 shared publications - Verawat Champreda
National Center for Genetic Engineering and Biotechnology (BIOTEC)
4 shared publications - Nuchanart Siri-Nguan
PTT Public Company Limited, Ayutthaya 10908, Thailand
3 shared publications - Worapon Kiatkittipong
Silpakorn University
3 shared publications - Chalempol Khajonvittayakul
Chemical and Process Engineering, The Sirindhorn International Thai-German Graduate School of Engineering (TGGS), King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
2 shared publications
Latest Publications
- Open Access
Lignin-Derived Syringol and Acetosyringone from Palm Bunch Using Heterogeneous Oxidative Depolymerization over Mixed Metal Oxide Catalysts under Microwave Heating
Biomass valorization to building block chemicals in food and pharmaceutical industries has tremendously gained attention. To produce monophenolic compounds from palm empty fruit bunch (EFB), EFB was subjected to alkaline hydrothermal extraction using NaOH or K2CO3 as a promotor. Subsequently, EFB-derived lignin was subjected to an oxidative depolymerization using Cu(II) and Fe(III) mixed metal oxides catalyst supported on γ-Al2O3 or SiO2 as the catalyst in the presence of hydrogen peroxide. The highest percentage of total phenolic compounds of 63.87 wt% was obtained from microwave-induced oxidative degradation of K2CO3 extracted lignin catalyzed by Cu-Fe/SiO2 catalyst. Main products from the aforementioned condition included 27.29 wt% of 2,4-di-tert-butylphenol, 19.21 wt% of syringol, 9.36 wt% of acetosyringone, 3.69 wt% of acetovanillone, 2.16 wt% of syringaldehyde, and 2.16 wt% of vanillin. Although the total phenolic compound from Cu-Fe/Al2O3 catalyst was lower (49.52 wt%) compared with that from Cu-Fe/SiO2 catalyst (63.87 wt%), Cu-Fe/Al2O3 catalyst provided the greater selectivity of main two value-added products, syringol and acetosyrigone, at 54.64% and 23.65%, respectively (78.29% total selectivity of two products) from the NaOH extracted lignin. The findings suggested a promising method for syringol and acetosyringone production from the oxidative heterogeneous lignin depolymerization under low power intensity microwave heating within a short reaction time of 30 min.
Open AccessLignin-Derived Syringol and Acetosyringone from Palm Bunch Using Heterogeneous Oxidative Depolymerization over Mixed Metal Oxide Catalysts under Microwave Heating
Biomass valorization to building block chemicals in food and pharmaceutical industries has tremendously gained attention. To produce monophenolic compounds from palm empty fruit bunch (EFB), EFB was subjected to alkaline hydrothermal extraction using NaOH or K2CO3 as a promotor. Subsequently, EFB-derived lignin was subjected to an oxidative depolymerization using Cu(II) and Fe(III) mixed metal oxides catalyst supported on γ-Al2O3 or SiO2 as the catalyst in the presence of hydrogen peroxide. The highest percentage of total phenolic compounds of 63.87 wt% was obtained from microwave-induced oxidative degradation of K2CO3 extracted lignin catalyzed by Cu-Fe/SiO2 catalyst. Main products from the aforementioned condition included 27.29 wt% of 2,4-di-tert-butylphenol, 19.21 wt% of syringol, 9.36 wt% of acetosyringone, 3.69 wt% of acetovanillone, 2.16 wt% of syringaldehyde, and 2.16 wt% of vanillin. Although the total phenolic compound from Cu-Fe/Al2O3 catalyst was lower (49.52 wt%) compared with that from Cu-Fe/SiO2 catalyst (63.87 wt%), Cu-Fe/Al2O3 catalyst provided the greater selectivity of main two value-added products, syringol and acetosyrigone, at 54.64% and 23.65%, respectively (78.29% total selectivity of two products) from the NaOH extracted lignin. The findings suggested a promising method for syringol and acetosyringone production from the oxidative heterogeneous lignin depolymerization under low power intensity microwave heating within a short reaction time of 30 min.
- Open Access
Process Intensification of Methane Production via Catalytic Hydrogenation in the Presence of Ni-CeO2/Cr2O3 Using a Micro-Channel Reactor
A slight amount of Cr2O3 segregation in 40 wt% NiO/Ce0.5Cr0.5O2 was presented at the surface. The best catalytic performance towards the reaction was achieved at 74% of CO2 conversion and 100% CH4 selectivity at 310 °C, the reactant (H2/CO2) feed molar ratio was 4, and the WHSV was 56,500 mlN·h−1·g−1cat. The mechanistic pathway was proposed through carbonates and formates as a mediator during CO2 and H2 interaction. Activation energy was estimated at 4.85 kJ/mol, when the orders of the reaction were ranging from 0.33 to 1.07 for nth-order, and 0.40 to 0.53 for mth-order.
Open AccessProcess Intensification of Methane Production via Catalytic Hydrogenation in the Presence of Ni-CeO2/Cr2O3 Using a Micro-Channel Reactor
A slight amount of Cr2O3 segregation in 40 wt% NiO/Ce0.5Cr0.5O2 was presented at the surface. The best catalytic performance towards the reaction was achieved at 74% of CO2 conversion and 100% CH4 selectivity at 310 °C, the reactant (H2/CO2) feed molar ratio was 4, and the WHSV was 56,500 mlN·h−1·g−1cat. The mechanistic pathway was proposed through carbonates and formates as a mediator during CO2 and H2 interaction. Activation energy was estimated at 4.85 kJ/mol, when the orders of the reaction were ranging from 0.33 to 1.07 for nth-order, and 0.40 to 0.53 for mth-order.
- Open Access
CO2 Hydrogenation to Synthetic Natural Gas over Ni, Fe and Co–Based CeO2–Cr2O3
CO2 methanation was studied over monometallic catalyst, i.e., Ni, Fe and Co; on CeO2-Cr2O3 support. The catalysts were prepared using one-pot hydrolysis of mixed metal nitrates and ammonium carbonate. Physicochemical properties of the pre- and post-exposure catalysts were characterized by X-Ray Powder Diffraction (XRD), Hydrogen Temperature Programmed Reduction (H2-TPR), and Field Emission Scanning Electron Microscope (FE-SEM). The screening of three dopants over CeO2-Cr2O3 for CO2 methanation was conducted in a milli-packed bed reactor. Ni-based catalyst was proven to be the most effective catalyst among all. Thus, a group of NiO/CeO2-Cr2O3 catalysts with Ni loading was investigated further. 40 % NiO/CeO2-Cr2O3 exhibited the highest CO2 conversion of 97.67% and CH4 selectivity of 100% at 290 °C. The catalytic stability of NiO/CeO2-Cr2O3 was tested towards the CO2 methanation reaction over 50 h of time-on-stream experiment, showing a good stability in term of catalytic activity.
Open AccessCO2 Hydrogenation to Synthetic Natural Gas over Ni, Fe and Co–Based CeO2–Cr2O3
CO2 methanation was studied over monometallic catalyst, i.e., Ni, Fe and Co; on CeO2-Cr2O3 support. The catalysts were prepared using one-pot hydrolysis of mixed metal nitrates and ammonium carbonate. Physicochemical properties of the pre- and post-exposure catalysts were characterized by X-Ray Powder Diffraction (XRD), Hydrogen Temperature Programmed Reduction (H2-TPR), and Field Emission Scanning Electron Microscope (FE-SEM). The screening of three dopants over CeO2-Cr2O3 for CO2 methanation was conducted in a milli-packed bed reactor. Ni-based catalyst was proven to be the most effective catalyst among all. Thus, a group of NiO/CeO2-Cr2O3 catalysts with Ni loading was investigated further. 40 % NiO/CeO2-Cr2O3 exhibited the highest CO2 conversion of 97.67% and CH4 selectivity of 100% at 290 °C. The catalytic stability of NiO/CeO2-Cr2O3 was tested towards the CO2 methanation reaction over 50 h of time-on-stream experiment, showing a good stability in term of catalytic activity.
- 15 September 2021
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (2) , 1646-1658
Mechanism of CaO catalyst deactivation with unconventional monitoring method for glycerol carbonate production via transesterification of glycerol with dimethyl carbonate
- 15 September 2021
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (2) , 1646-1658
Mechanism of CaO catalyst deactivation with unconventional monitoring method for glycerol carbonate production via transesterification of glycerol with dimethyl carbonate
- Open Access
Photocatalytic Hydrogen Production from Urine Using Sr-Doped TiO2 Photocatalyst with Subsequent Phosphorus Recovery via Struvite Crystallization
Currently, the discharge of wastewater and utilization of phosphorus (P) in human activities cause some environmental problems, such as high organic pollutants in aquatic environments which results in dirty water sources, and a shortage of phosphate rock reserves due to the high demand of P. Therefore, fuel energy and struvite crystallization from waste sources can be considered interesting alternatives. In this work, the modified catalyst for hydrogen production, along with solving environmental problems, was examined. The strontium (Sr) doped-titanium dioxide (TiO2) nanoparticles were synthesized by wetness impregnation method. The synthesized catalyst was characterized using UV-vis spectroscopy (UV-vis), photoluminescence (PL), X-ray diffraction (XRD), photoluminescence (PL), and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS). The Sr-doped TiO2 catalysts had been utilized as the photocatalyst for the hydrogen production from synthetic human urine (a representative of waste source). The doping content of Sr in TiO2 varied from 0.5, 1, 2, and 4%, and the photocatalytic performances were compared with pristine TiO2 nanoparticles. The results showed that 1% Sr-doped TiO2 had the highest photocatalytic activity for hydrogen production and decreased the amount of chemical oxygen demand (COD) in the synthetic human urine. Subsequently, P could be recovered from the treated human urine in the form of struvite.
Open AccessPhotocatalytic Hydrogen Production from Urine Using Sr-Doped TiO2 Photocatalyst with Subsequent Phosphorus Recovery via Struvite Crystallization
Currently, the discharge of wastewater and utilization of phosphorus (P) in human activities cause some environmental problems, such as high organic pollutants in aquatic environments which results in dirty water sources, and a shortage of phosphate rock reserves due to the high demand of P. Therefore, fuel energy and struvite crystallization from waste sources can be considered interesting alternatives. In this work, the modified catalyst for hydrogen production, along with solving environmental problems, was examined. The strontium (Sr) doped-titanium dioxide (TiO2) nanoparticles were synthesized by wetness impregnation method. The synthesized catalyst was characterized using UV-vis spectroscopy (UV-vis), photoluminescence (PL), X-ray diffraction (XRD), photoluminescence (PL), and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS). The Sr-doped TiO2 catalysts had been utilized as the photocatalyst for the hydrogen production from synthetic human urine (a representative of waste source). The doping content of Sr in TiO2 varied from 0.5, 1, 2, and 4%, and the photocatalytic performances were compared with pristine TiO2 nanoparticles. The results showed that 1% Sr-doped TiO2 had the highest photocatalytic activity for hydrogen production and decreased the amount of chemical oxygen demand (COD) in the synthetic human urine. Subsequently, P could be recovered from the treated human urine in the form of struvite.
- Open Access
Process and Energy Intensification of Glycerol Carbonate Production from Glycerol and Dimethyl Carbonate in the Presence of Eggshell-Derived CaO Heterogeneous Catalyst
The process and energy intensifications for the synthesis of glycerol carbonate (GC) from glycerol and dimethyl carbonate (DMC) using an eggshell-derived CaO heterogeneous catalyst were investigated. The transesterification reaction between glycerol and DMC was typically limited by mass transfer because of the immiscible nature of the reactants. By varying the stirring speed, it was observed that the mass transfer limitation could be neglected at 800 rpm. The presence of the CaO solid catalyst made the mass transport-limited reaction process more prominent. Mass transfer intensification using a simple kitchen countertop blender as an alternative to overcome the external mass transfer limitation of a typical magnetic stirrer was demonstrated. A lower amount of the catalyst and a shorter reaction time were required to achieve 93% glycerol conversion or 91% GC yield, and the turnover frequency (TOF) increased almost 5 times from 1.5 to 7.2 min−1 when using a conventional magnetic stirrer and countertop blender, respectively. In addition, using a simple kitchen countertop blender with 7200 rpm, the reaction temperature of 60 °C could be reached within approximately 3 min without the need of a heating unit. This was the result of the self-frictional heat generated by the high-shear blender. This was considered to be heat transfer intensification, as heat was generated locally (in situ), offering a higher homogeneity distribution. Meanwhile, the trend toward energy intensification was promising as the yield efficiency increased from 0.064 to 2.391 g/kJ. A comparison among other process intensification techniques, e.g., microwave reactor, ultrasonic reactor, and reactive distillation was also rationalized.
Open AccessProcess and Energy Intensification of Glycerol Carbonate Production from Glycerol and Dimethyl Carbonate in the Presence of Eggshell-Derived CaO Heterogeneous Catalyst
The process and energy intensifications for the synthesis of glycerol carbonate (GC) from glycerol and dimethyl carbonate (DMC) using an eggshell-derived CaO heterogeneous catalyst were investigated. The transesterification reaction between glycerol and DMC was typically limited by mass transfer because of the immiscible nature of the reactants. By varying the stirring speed, it was observed that the mass transfer limitation could be neglected at 800 rpm. The presence of the CaO solid catalyst made the mass transport-limited reaction process more prominent. Mass transfer intensification using a simple kitchen countertop blender as an alternative to overcome the external mass transfer limitation of a typical magnetic stirrer was demonstrated. A lower amount of the catalyst and a shorter reaction time were required to achieve 93% glycerol conversion or 91% GC yield, and the turnover frequency (TOF) increased almost 5 times from 1.5 to 7.2 min−1 when using a conventional magnetic stirrer and countertop blender, respectively. In addition, using a simple kitchen countertop blender with 7200 rpm, the reaction temperature of 60 °C could be reached within approximately 3 min without the need of a heating unit. This was the result of the self-frictional heat generated by the high-shear blender. This was considered to be heat transfer intensification, as heat was generated locally (in situ), offering a higher homogeneity distribution. Meanwhile, the trend toward energy intensification was promising as the yield efficiency increased from 0.064 to 2.391 g/kJ. A comparison among other process intensification techniques, e.g., microwave reactor, ultrasonic reactor, and reactive distillation was also rationalized.
- Open Access
A Dual Reactor for Isothermal Thermochemical Cycles of H2O/CO2 Co-Splitting Using La0.3Sr0.7Co0.7Fe0.3O3 as an Oxygen Carrier
Catalytic performance of La0.3Sr0.7Co0.7Fe0.3O3 (LSCF3773 or LSCF) catalyst for syngas production via two step thermochemical cycles of H2O and CO2 co-splitting was investigated. Oxygen storage capacity (OSC) was found to depend on reduction temperature, rather than the oxidation temperature. The highest oxygen vacancy (Δδ) was achieved when the reduction and oxidation temperature were both fixed at 900 °C with the feed ratio (H2O to CO2) of 3 to 1, with an increasing amount of CO2 in the feed mixture. CO productivity reached its plateau at high ratios of H2O to CO2 (1:1, 1:2, and 1:2.5), while the total productivities were reduced with the same ratios. This indicated the existence of a CO2 blockage, which was the result of either high Ea of CO2 dissociation or high Ea of CO desorption, resulting in the loss in active species. From the results, it can be concluded that H2O and CO2 splitting reactions were competitive reactions. Ea of H2O and CO2 splitting was estimated at 31.01 kJ/mol and 48.05 kJ/mol, respectively, which agreed with the results obtained from the experimentation of the effect of the oxidation temperature. A dual-reactors system was applied to provide a continuous product stream, where the operation mode was switched between the reduction and oxidation step. The isothermal thermochemical cycles process, where the reduction and oxidation were performed at the same temperature, was also carried out in order to increase the overall efficiency of the process. The optimal time for the reduction and oxidation step was found to be 30 min for each step, giving total productivity of the syngas mixture at 28,000 μmol/g, approximately.
Open AccessA Dual Reactor for Isothermal Thermochemical Cycles of H2O/CO2 Co-Splitting Using La0.3Sr0.7Co0.7Fe0.3O3 as an Oxygen Carrier
Catalytic performance of La0.3Sr0.7Co0.7Fe0.3O3 (LSCF3773 or LSCF) catalyst for syngas production via two step thermochemical cycles of H2O and CO2 co-splitting was investigated. Oxygen storage capacity (OSC) was found to depend on reduction temperature, rather than the oxidation temperature. The highest oxygen vacancy (Δδ) was achieved when the reduction and oxidation temperature were both fixed at 900 °C with the feed ratio (H2O to CO2) of 3 to 1, with an increasing amount of CO2 in the feed mixture. CO productivity reached its plateau at high ratios of H2O to CO2 (1:1, 1:2, and 1:2.5), while the total productivities were reduced with the same ratios. This indicated the existence of a CO2 blockage, which was the result of either high Ea of CO2 dissociation or high Ea of CO desorption, resulting in the loss in active species. From the results, it can be concluded that H2O and CO2 splitting reactions were competitive reactions. Ea of H2O and CO2 splitting was estimated at 31.01 kJ/mol and 48.05 kJ/mol, respectively, which agreed with the results obtained from the experimentation of the effect of the oxidation temperature. A dual-reactors system was applied to provide a continuous product stream, where the operation mode was switched between the reduction and oxidation step. The isothermal thermochemical cycles process, where the reduction and oxidation were performed at the same temperature, was also carried out in order to increase the overall efficiency of the process. The optimal time for the reduction and oxidation step was found to be 30 min for each step, giving total productivity of the syngas mixture at 28,000 μmol/g, approximately.
- Open Access
- 18 December 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (12) , 2548
Effect of Water and Glycerol in Deoxygenation of Coconut Oil over Bimetallic NiCo/SAPO-11 Nanocatalyst under N2 Atmosphere
The catalytic deoxygenation of coconut oil was performed in a continuous-flow reactor over bimetallic NiCo/silicoaluminophosphate-11 (SAPO-11) nanocatalysts for hydrocarbon fuel production. The conversion and product distribution were investigated over NiCo/SAPO-11 with different applied co-reactants, i.e., water (H2O) or glycerol solution, performed under nitrogen (N2) atmosphere. The hydrogen-containing co-reactants were proposed here as in-situ hydrogen sources for the deoxygenation, while the reaction tests under hydrogen (H2) atmosphere were also applied as a reference set of experiments. The results showed that applying co-reactants to the reaction enhanced the oil conversion as the following order: N2 (no co-reactant) < N2 (H2O) < N2 (aqueous glycerol) < H2 (reference). The main products formed under the existence of H2O or glycerol solution were free fatty acids (FFAs) and their corresponding Cn−1 alkanes. The addition of H2O aids the triglyceride breakdown into FFAs, whereas the glycerol acts as hydrogen donor which is favourable to initiate hydrogenolysis of triglycerides, causing higher amount of FFAs than the former case. Consequently, those FFAs can be deoxygenated via decarbonylation/decarboxylation to their corresponding Cn−1 alkanes, showing the promising capability of the NiCo/SAPO-11 to produce hydrocarbon fuels even in the absence of external H2 source.
- 18 December 2020
- Published by MDPI AG in Nanomaterials
- Vol. 10 (12) , 2548
Open AccessEffect of Water and Glycerol in Deoxygenation of Coconut Oil over Bimetallic NiCo/SAPO-11 Nanocatalyst under N2 Atmosphere
The catalytic deoxygenation of coconut oil was performed in a continuous-flow reactor over bimetallic NiCo/silicoaluminophosphate-11 (SAPO-11) nanocatalysts for hydrocarbon fuel production. The conversion and product distribution were investigated over NiCo/SAPO-11 with different applied co-reactants, i.e., water (H2O) or glycerol solution, performed under nitrogen (N2) atmosphere. The hydrogen-containing co-reactants were proposed here as in-situ hydrogen sources for the deoxygenation, while the reaction tests under hydrogen (H2) atmosphere were also applied as a reference set of experiments. The results showed that applying co-reactants to the reaction enhanced the oil conversion as the following order: N2 (no co-reactant) < N2 (H2O) < N2 (aqueous glycerol) < H2 (reference). The main products formed under the existence of H2O or glycerol solution were free fatty acids (FFAs) and their corresponding Cn−1 alkanes. The addition of H2O aids the triglyceride breakdown into FFAs, whereas the glycerol acts as hydrogen donor which is favourable to initiate hydrogenolysis of triglycerides, causing higher amount of FFAs than the former case. Consequently, those FFAs can be deoxygenated via decarbonylation/decarboxylation to their corresponding Cn−1 alkanes, showing the promising capability of the NiCo/SAPO-11 to produce hydrocarbon fuels even in the absence of external H2 source.
- Open Access
Enhancement of Photocatalytic Oxidation of Glucose to Value-Added Chemicals on TiO2 Photocatalysts by A Zeolite (Type Y) Support and Metal Loading
TiO2-based photocatalysts synthesized by the microwave-assisted sol-gel method was tested in the photocatalytic glucose conversion. Modifications of TiO2 with type-Y zeolite (ZeY) and metals (Ag, Cu, and Ag-Cu) were developed for increasing the dispersion of TiO2 nanoparticles and increasing the photocatalytic activity. Effects of the TiO2 dosage to zeolite ratio (i.e., TiO2/ZeY of 10, 20, 40, and 50 mol %) and the silica to alumina ratio in ZeY (i.e., SiO2:Al2O3 of 10, 100, and 500) were firstly studied. It was found that the specific surface area of TiO2/ZeY was 400–590 m2g−1, which was higher than that of pristine TiO2 (34.38 m2g−1). The good properties of 20%TiO2/ZeY photocatalyst, including smaller particles (13.27 nm) and high surface area, could achieve the highest photocatalytic glucose conversion (75%). Yields of gluconic acid, arabinose, xylitol, and formic acid obtained from 20%TiO2/ZeY were 9%, 26%, 4%, and 35%, respectively. For the effect of the silica to alumina ratio, the highest glucose conversion was obtained from SiO2:Al2O3 ratio of 100. Interestingly, it was found that the SiO2:Al2O3 ratio affected the selectivity of carboxylic products (gluconic acid and formic acid). At a low ratio of silica to alumina (SiO2:Al2O3 = 10), higher selectivity of the carboxylic products (gluconic acid = 29% and formic acid = 32%) was obtained (compared with other higher ratios). TiO2/ZeY was further loaded by metals using the microwave-assisted incipient wetness impregnation technique. The highest glucose conversion of 96.9 % was obtained from 1 wt. % Ag-TiO2 (40%)/ZeY. Furthermore, the bimetallic Ag-Cu-loaded TiO2/ZeY presented the highest xylitol yield of 12.93%.
Open AccessEnhancement of Photocatalytic Oxidation of Glucose to Value-Added Chemicals on TiO2 Photocatalysts by A Zeolite (Type Y) Support and Metal Loading
TiO2-based photocatalysts synthesized by the microwave-assisted sol-gel method was tested in the photocatalytic glucose conversion. Modifications of TiO2 with type-Y zeolite (ZeY) and metals (Ag, Cu, and Ag-Cu) were developed for increasing the dispersion of TiO2 nanoparticles and increasing the photocatalytic activity. Effects of the TiO2 dosage to zeolite ratio (i.e., TiO2/ZeY of 10, 20, 40, and 50 mol %) and the silica to alumina ratio in ZeY (i.e., SiO2:Al2O3 of 10, 100, and 500) were firstly studied. It was found that the specific surface area of TiO2/ZeY was 400–590 m2g−1, which was higher than that of pristine TiO2 (34.38 m2g−1). The good properties of 20%TiO2/ZeY photocatalyst, including smaller particles (13.27 nm) and high surface area, could achieve the highest photocatalytic glucose conversion (75%). Yields of gluconic acid, arabinose, xylitol, and formic acid obtained from 20%TiO2/ZeY were 9%, 26%, 4%, and 35%, respectively. For the effect of the silica to alumina ratio, the highest glucose conversion was obtained from SiO2:Al2O3 ratio of 100. Interestingly, it was found that the SiO2:Al2O3 ratio affected the selectivity of carboxylic products (gluconic acid and formic acid). At a low ratio of silica to alumina (SiO2:Al2O3 = 10), higher selectivity of the carboxylic products (gluconic acid = 29% and formic acid = 32%) was obtained (compared with other higher ratios). TiO2/ZeY was further loaded by metals using the microwave-assisted incipient wetness impregnation technique. The highest glucose conversion of 96.9 % was obtained from 1 wt. % Ag-TiO2 (40%)/ZeY. Furthermore, the bimetallic Ag-Cu-loaded TiO2/ZeY presented the highest xylitol yield of 12.93%.
- Open Access
Comparison of Packed-Bed and Micro-Channel Reactors for Hydrogen Production via Thermochemical Cycles of Water Splitting in the Presence of Ceria-Based Catalysts
Hydrogen production via two-step thermochemical cycles over fluorite-structure ceria (CeO2) and ceria-zirconia (Ce0.75Zr0.25O2) materials was studied in packed-bed and micro-channel reactors for comparison purposes. The H2-temperature program reduction (H2-TPR) results indicated that the addition of Zr4+ enhanced the material’s reducibility from 585 µmol/g to 1700 µmol/g, although the reduction temperature increased from 545 to 680 °C. Ce0.75Zr0.25O2 was found to offer higher hydrogen productivity than CeO2 regardless of the type of reactor. The micro-channel reactor showed better performance than the packed-bed reactor for this reaction.
Open AccessComparison of Packed-Bed and Micro-Channel Reactors for Hydrogen Production via Thermochemical Cycles of Water Splitting in the Presence of Ceria-Based Catalysts
Hydrogen production via two-step thermochemical cycles over fluorite-structure ceria (CeO2) and ceria-zirconia (Ce0.75Zr0.25O2) materials was studied in packed-bed and micro-channel reactors for comparison purposes. The H2-temperature program reduction (H2-TPR) results indicated that the addition of Zr4+ enhanced the material’s reducibility from 585 µmol/g to 1700 µmol/g, although the reduction temperature increased from 545 to 680 °C. Ce0.75Zr0.25O2 was found to offer higher hydrogen productivity than CeO2 regardless of the type of reactor. The micro-channel reactor showed better performance than the packed-bed reactor for this reaction.