Bo Diao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bo Diao has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Yinghua Ye
School of Transportation Science and Engineering, Beihang University, Beijing 100191, China
6 shared publications - Shaohong Cheng
Department of Civil and Environmental Engineering, University of Windsor, 401 Sunset Ave., Windsor, Ontario N9B 3P4, Canada
4 shared publications Yinghua Ye
School of Transportation Science and Engineering, Beihang University, Beijing 100083, China
3 shared publicationsJian Zhang
School of Transportation Science and Engineering
2 shared publications- Jieqiong Wu
Ph.D. Student, School of Transportation Science and Engineering, Beihang Univ., 37 Xueyuan Rd., Haidian District, Beijing 100191, China. ORCID:
2 shared publications - Quanquan Guo
Beihang University
2 shared publications
Latest Publications
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Parametric Study on Mixed Torsional Behavior of U‐Shaped Thin‐Walled RC Girders
Nowadays, U‐shaped thin‐walled concrete girders have been widely applied in the urban construction of rail viaducts in China as well as worldwide. However, the mixed torsional behaviors of these structures are not well understood. In this paper, the mixed torsional behaviors of the U‐shaped thin‐walled RC girders are theoretically analyzed, and a method predicting failure modes and ultimate torques is proposed. Nonlinear FE models based on ABAQUS to simulate the mixed torsional behaviors are built and calibrated with the test results. Parametric studies considering three crucial parameters (boundary condition, span length‐section height ratio, and ratio of longitudinal bars to stirrups) are conducted based on both the above suggested calculating method and the FE modeling. The calculated and the simulated results agree well with each other and with the test results. It is found that the failure modes of the U‐shaped thin‐walled RC girders under torsion are influenced by all the three parameters. Three kinds of failure modes are observed: flexural failures dominated by warping moment, shear failures caused by warping torque and circulatory torque, and flexural‐shear failures in the cases where flexural failure and shear failure appear almost at the same time.
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Open AccessParametric Study on Mixed Torsional Behavior of U‐Shaped Thin‐Walled RC Girders
Nowadays, U‐shaped thin‐walled concrete girders have been widely applied in the urban construction of rail viaducts in China as well as worldwide. However, the mixed torsional behaviors of these structures are not well understood. In this paper, the mixed torsional behaviors of the U‐shaped thin‐walled RC girders are theoretically analyzed, and a method predicting failure modes and ultimate torques is proposed. Nonlinear FE models based on ABAQUS to simulate the mixed torsional behaviors are built and calibrated with the test results. Parametric studies considering three crucial parameters (boundary condition, span length‐section height ratio, and ratio of longitudinal bars to stirrups) are conducted based on both the above suggested calculating method and the FE modeling. The calculated and the simulated results agree well with each other and with the test results. It is found that the failure modes of the U‐shaped thin‐walled RC girders under torsion are influenced by all the three parameters. Three kinds of failure modes are observed: flexural failures dominated by warping moment, shear failures caused by warping torque and circulatory torque, and flexural‐shear failures in the cases where flexural failure and shear failure appear almost at the same time.
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Hysteretic Behavior of Eccentrically Loaded Reinforced Air‐Entrained Concrete Columns under Combined Effects of Freeze‐Thaw Cycles and Seawater Corrosion
Besides service loads, reinforced concrete structures in cold coastal seismic regions are subjected to multiple attacks of freeze‐thaw cycles and seawater corrosion as well as the earthquake struck. An experimental study was conducted to investigate the seismic response of eccentrically loaded reinforced air‐entrained concrete columns under alternative actions of freeze‐thaw cycles and chloride corrosion. Results show that, after 300 times of freeze‐thaw cycles alternated with 100 times of seawater immersion, the hysteretic behavior of the eccentrically loaded columns manifested an apparent asymmetric pattern. Under forward cyclic load, the existence of larger eccentric load rendered the reduction of the ultimate load and the ductility of a column by up to 20.3% and 46.05%, respectively, but it had a positive effect if reverse cyclic load was applied. The presence of eccentric load could have a considerable impact on the seismic behavior of reinforced air‐entrained concrete columns served in an aggressive environment.
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Open AccessHysteretic Behavior of Eccentrically Loaded Reinforced Air‐Entrained Concrete Columns under Combined Effects of Freeze‐Thaw Cycles and Seawater Corrosion
Besides service loads, reinforced concrete structures in cold coastal seismic regions are subjected to multiple attacks of freeze‐thaw cycles and seawater corrosion as well as the earthquake struck. An experimental study was conducted to investigate the seismic response of eccentrically loaded reinforced air‐entrained concrete columns under alternative actions of freeze‐thaw cycles and chloride corrosion. Results show that, after 300 times of freeze‐thaw cycles alternated with 100 times of seawater immersion, the hysteretic behavior of the eccentrically loaded columns manifested an apparent asymmetric pattern. Under forward cyclic load, the existence of larger eccentric load rendered the reduction of the ultimate load and the ductility of a column by up to 20.3% and 46.05%, respectively, but it had a positive effect if reverse cyclic load was applied. The presence of eccentric load could have a considerable impact on the seismic behavior of reinforced air‐entrained concrete columns served in an aggressive environment.
- Open Access
- 10 August 2017
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2017, 1-15
Impact of Cyclic Loading on Chloride Diffusivity and Mechanical Performance of RC Beams under Seawater Corrosion
An experimental study was conducted to investigate the impact of cyclic loading on the mechanical performance and chloride diffusivity of RC beams exposed to seawater wet-dry cycles. To induce initial damage to RC beam specimen, cyclic loading controlled by max load and cycles was applied. Then beam specimens underwent 240 wet-dry cycles of seawater. Results show that the chloride content increased as max load and cycle increased. The chloride content at steel surface increased approximatively linearly as average crack width increased. Moreover, the max load had more influence on chloride content at steel surface than cycle. The difference of average chloride diffusion coefficient between tension and compression concrete was little at uncracked position. Average chloride diffusion coefficient increased as crack width increased when crack width was less than 0.11 mm whereas the increasing tendency was weak when crack width exceeded 0.11 mm. The residual yield load and ultimate load of RC beams decreased as max load and cycle increased. Based on univariate analysis of variance, the max load had more adverse effect on yield load and ultimate load than cycle.
- 10 August 2017
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2017, 1-15
Open AccessImpact of Cyclic Loading on Chloride Diffusivity and Mechanical Performance of RC Beams under Seawater Corrosion
An experimental study was conducted to investigate the impact of cyclic loading on the mechanical performance and chloride diffusivity of RC beams exposed to seawater wet-dry cycles. To induce initial damage to RC beam specimen, cyclic loading controlled by max load and cycles was applied. Then beam specimens underwent 240 wet-dry cycles of seawater. Results show that the chloride content increased as max load and cycle increased. The chloride content at steel surface increased approximatively linearly as average crack width increased. Moreover, the max load had more influence on chloride content at steel surface than cycle. The difference of average chloride diffusion coefficient between tension and compression concrete was little at uncracked position. Average chloride diffusion coefficient increased as crack width increased when crack width was less than 0.11 mm whereas the increasing tendency was weak when crack width exceeded 0.11 mm. The residual yield load and ultimate load of RC beams decreased as max load and cycle increased. Based on univariate analysis of variance, the max load had more adverse effect on yield load and ultimate load than cycle.
- Open Access
- 1 January 2017
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2017, 1-13
Chloride Diffusivity and Life Prediction of Cracked RC Beams Exposed to Different Wet-Dry Ratios and Exposure Duration
Effects of crack width, wet-dry ratio, and exposure duration of wet-dry cycles on chloride ingress of RC beams were experimentally studied. Crack widths of 40, 70, 90, and 120 microns were, respectively, induced by three-point flexural loading and four wet-dry ratios (seawater spraying 1 d in one wet-dry cycle) of 1 : 3, 1 : 7, 1 : 11, and 1 : 15 were selected. Chloride contents of RC beams were tested every 32 d (or 16 d) of wet-dry cycles. Results show that chloride content increased significantly when crack width was larger than 90 microns and wet-dry ratio was 1 : 3, and it increased slightly when crack width was 120 microns and wet-dry ratio was 1 : 7, 1 : 11, and 1 : 15. The chloride content on steel bar surface became the largest when crack width was less than 90 microns and wet-dry ratio was 1 : 7, and while crack width was equal to or greater than 90 microns and wet-dry ratio was 1 : 3, it was the largest. Based on the testing results, chloride diffusion model and prediction model of residual service life of RC beams were suggested considering combined effects of crack width and exposure duration. The predicted residual service lives were corresponding well with experimental results and they decreased as crack width increased.
- 1 January 2017
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2017, 1-13
Open AccessChloride Diffusivity and Life Prediction of Cracked RC Beams Exposed to Different Wet-Dry Ratios and Exposure Duration
Effects of crack width, wet-dry ratio, and exposure duration of wet-dry cycles on chloride ingress of RC beams were experimentally studied. Crack widths of 40, 70, 90, and 120 microns were, respectively, induced by three-point flexural loading and four wet-dry ratios (seawater spraying 1 d in one wet-dry cycle) of 1 : 3, 1 : 7, 1 : 11, and 1 : 15 were selected. Chloride contents of RC beams were tested every 32 d (or 16 d) of wet-dry cycles. Results show that chloride content increased significantly when crack width was larger than 90 microns and wet-dry ratio was 1 : 3, and it increased slightly when crack width was 120 microns and wet-dry ratio was 1 : 7, 1 : 11, and 1 : 15. The chloride content on steel bar surface became the largest when crack width was less than 90 microns and wet-dry ratio was 1 : 7, and while crack width was equal to or greater than 90 microns and wet-dry ratio was 1 : 3, it was the largest. Based on the testing results, chloride diffusion model and prediction model of residual service life of RC beams were suggested considering combined effects of crack width and exposure duration. The predicted residual service lives were corresponding well with experimental results and they decreased as crack width increased.
- Open Access
- 1 January 2017
- Published by Wiley in Advances in Civil Engineering
- Vol. 2017, 1-11
Bond Effects between Concrete and Steel Bar Using Different Diameter Bars and Different Initial Crack Width
The importance of an accurate simulation of service conditions in the bond performance of reinforced concrete structures in coastal regions is highlighted. Four widths of initial crack of 0, 80, 150, and 210 microns were artificially made by inserting slice into bond specimens during concrete casting. Three bar diameters of 10 mm, 14 mm, and 18 mm were selected. At 28 days, the bond specimens were exposed to the environment of wet-dry cycles of seawater and atmosphere for another 90 days. The pull-out test was then conducted and chloride contents were tested at crack area along 40 mm depth. Results show that, for the specimen with 10 mm bar diameter, cracks width of less than 80 microns vanished rapidly during wet-dry cycles; for other specimens, cracks width of 100–150 microns decreased slightly. However the cracks of width more than 200 microns increased gradually; the chloride content decreased along the depth of concrete, and the chloride content increased as the widths of initial cracks increased or as the bar diameters increased. The ductility of bond specimens decreased as the diameter increased.
- 1 January 2017
- Published by Wiley in Advances in Civil Engineering
- Vol. 2017, 1-11
Open AccessBond Effects between Concrete and Steel Bar Using Different Diameter Bars and Different Initial Crack Width
The importance of an accurate simulation of service conditions in the bond performance of reinforced concrete structures in coastal regions is highlighted. Four widths of initial crack of 0, 80, 150, and 210 microns were artificially made by inserting slice into bond specimens during concrete casting. Three bar diameters of 10 mm, 14 mm, and 18 mm were selected. At 28 days, the bond specimens were exposed to the environment of wet-dry cycles of seawater and atmosphere for another 90 days. The pull-out test was then conducted and chloride contents were tested at crack area along 40 mm depth. Results show that, for the specimen with 10 mm bar diameter, cracks width of less than 80 microns vanished rapidly during wet-dry cycles; for other specimens, cracks width of 100–150 microns decreased slightly. However the cracks of width more than 200 microns increased gradually; the chloride content decreased along the depth of concrete, and the chloride content increased as the widths of initial cracks increased or as the bar diameters increased. The ductility of bond specimens decreased as the diameter increased.
- 25 December 2016
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 60 (6) , 1039-1061
Nonlinear model to predict the torsional response of U-shaped thin-walled RC members
- 25 December 2016
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 60 (6) , 1039-1061
Nonlinear model to predict the torsional response of U-shaped thin-walled RC members
- Open Access
- 5 October 2016
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2016, 1-10
Mechanical Performance and Chloride Diffusivity of Cracked RC Specimens Exposed to Freeze-Thaw Cycles and Intermittent Immersion in Seawater
The effects of crack width on chloride ingress and mechanical behavior of reinforced concrete (RC) specimens were experimentally studied after exposure to 300 cycles of freeze-thaw and seawater immersion (75 times). Cracks were induced prior to exposure by an eccentric compression load which was sustained until the end of the exposure period. The maximum cracks widths induced in the four column specimens were 0, 0.06, 0.11, and 0.15 mm, respectively. Results show that when the crack width was less than 0.06 mm, the effect of cracks on chloride ingress could be neglected. However, when the crack width was more than 0.11 mm, chloride ingress was accelerated. Results of static loading tests show that both yield load and ultimate load of RC columns decreased as crack width increased. When the crack width was 0.15 mm, yield load and ultimate load of RC column specimen decreased by 17.0% and 18.9%, respectively, compared to a specimen without cracks. It was concluded that crack width significantly promoted local chloride ingress and mechanical performance degradation of RC structures in cold coastal regions or exposed to deicing salts.
- 5 October 2016
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2016, 1-10
Open AccessMechanical Performance and Chloride Diffusivity of Cracked RC Specimens Exposed to Freeze-Thaw Cycles and Intermittent Immersion in Seawater
The effects of crack width on chloride ingress and mechanical behavior of reinforced concrete (RC) specimens were experimentally studied after exposure to 300 cycles of freeze-thaw and seawater immersion (75 times). Cracks were induced prior to exposure by an eccentric compression load which was sustained until the end of the exposure period. The maximum cracks widths induced in the four column specimens were 0, 0.06, 0.11, and 0.15 mm, respectively. Results show that when the crack width was less than 0.06 mm, the effect of cracks on chloride ingress could be neglected. However, when the crack width was more than 0.11 mm, chloride ingress was accelerated. Results of static loading tests show that both yield load and ultimate load of RC columns decreased as crack width increased. When the crack width was 0.15 mm, yield load and ultimate load of RC column specimen decreased by 17.0% and 18.9%, respectively, compared to a specimen without cracks. It was concluded that crack width significantly promoted local chloride ingress and mechanical performance degradation of RC structures in cold coastal regions or exposed to deicing salts.
- 1 March 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 27 (1) , 44-53
Effects of Freeze-Thaw Cycles and Seawater Corrosion on the Behavior of Reinforced Air-Entrained Concrete Beams with Persistent Loads
The effects of freeze-thaw cycles and seawater corrosion on the material properties of air-entrained concrete specimens and structural behavior of reinforced air-entrained concrete beams under persistent loads were investigated in the laboratory. The air content of the specimens was designed to be 3.2 and 6.1%. Results show that when subjected to alternating actions of freeze-thaw cycles and seawater immersion, the compressive strength of concrete decreased when the number of freeze-thaw cycles increased, with the ones with higher air content showing better resistance to freeze-thaw attack. In the case of reinforced air-entrained concrete beam, the presence of persistent loads accelerated the structural behavior deterioration process. When the persistent load reached half of the ultimate load, the reduction of the ultimate load and ductility was found to be a couple of times greater than those without the persistent load. Compared to the beams with 3.2% air content, the yield load, the ultimate lo...
- 1 March 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 27 (1) , 44-53
Effects of Freeze-Thaw Cycles and Seawater Corrosion on the Behavior of Reinforced Air-Entrained Concrete Beams with Persistent Loads
The effects of freeze-thaw cycles and seawater corrosion on the material properties of air-entrained concrete specimens and structural behavior of reinforced air-entrained concrete beams under persistent loads were investigated in the laboratory. The air content of the specimens was designed to be 3.2 and 6.1%. Results show that when subjected to alternating actions of freeze-thaw cycles and seawater immersion, the compressive strength of concrete decreased when the number of freeze-thaw cycles increased, with the ones with higher air content showing better resistance to freeze-thaw attack. In the case of reinforced air-entrained concrete beam, the presence of persistent loads accelerated the structural behavior deterioration process. When the persistent load reached half of the ultimate load, the reduction of the ultimate load and ductility was found to be a couple of times greater than those without the persistent load. Compared to the beams with 3.2% air content, the yield load, the ultimate lo...
- 23 July 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 3112-3121
Exploration on Low-Temperature Properties of SBS Modified Asphalt for Pavement
Low-temperature properties of the styrene-butadiene-styrene (SBS) modified asphalt are investigated using conventional methods and bending beam rheometer (BBR). Effects of the characteristics of base asphalt and SBS type on these properties are evaluated. The results indicate that SBS didn't substantially improve low-temperature properties of base asphalt. Low temperature properties of SBS modified asphalts are more associated with low temperature properties of base asphalts, and slightly with SBS modifier type. Different low-temperature parameters are also discussed showing that conventional low temperature indicators are not appropriate for characterizing low temperature properties of SBS modified asphalt.
- 23 July 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 3112-3121
Exploration on Low-Temperature Properties of SBS Modified Asphalt for Pavement
Low-temperature properties of the styrene-butadiene-styrene (SBS) modified asphalt are investigated using conventional methods and bending beam rheometer (BBR). Effects of the characteristics of base asphalt and SBS type on these properties are evaluated. The results indicate that SBS didn't substantially improve low-temperature properties of base asphalt. Low temperature properties of SBS modified asphalts are more associated with low temperature properties of base asphalts, and slightly with SBS modifier type. Different low-temperature parameters are also discussed showing that conventional low temperature indicators are not appropriate for characterizing low temperature properties of SBS modified asphalt.
- 23 July 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 3218-3227
Study on the New Measurement Technology for Evaluating the Cracking Performance of an Airport Runway under Construction Based on Airport Pavement Operational Safety
Based on the airport pavement operational safety, this article discusses the development of a new technology for evaluating the anti-cracking performance of airport concrete runways under construction. This dumbbell test technology can help evaluate the effects of different factors on the anti-cracking performance of airport concrete runways with the new device of stress risers. This method can rapidly evaluate the anti-cracking performance of runways with different concrete materials at the construction site. This new test technology can provide solutions to choosing the most suitable materials and concrete mix ratios for the improvement of anti-cracking performance of airport concrete runways under construction. The paper also conducted a comparative study with another two test methods of concrete anti-cracking performance (ring method and slab test method) under constraint conditions.
- 23 July 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 3218-3227
Study on the New Measurement Technology for Evaluating the Cracking Performance of an Airport Runway under Construction Based on Airport Pavement Operational Safety
Based on the airport pavement operational safety, this article discusses the development of a new technology for evaluating the anti-cracking performance of airport concrete runways under construction. This dumbbell test technology can help evaluate the effects of different factors on the anti-cracking performance of airport concrete runways with the new device of stress risers. This method can rapidly evaluate the anti-cracking performance of runways with different concrete materials at the construction site. This new test technology can provide solutions to choosing the most suitable materials and concrete mix ratios for the improvement of anti-cracking performance of airport concrete runways under construction. The paper also conducted a comparative study with another two test methods of concrete anti-cracking performance (ring method and slab test method) under constraint conditions.