Suha Orçun Mert
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Suha Orçun Mert has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Ceyda Kök
Iskenderun Technical University
4 shared publications Alper Reis
3 shared publicationsZehra Özçelik
3 shared publications- Alper Reis
Yuzuncu Yıl University, Faculty of Engineering and Architecture
2 shared publications I. Dincer
2 shared publicationsIbrahim Dincer
2 shared publications
Latest Publications
- Open Access
- 3 February 2023
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 2023, 1-16
Energetic and Exergetic Performance Investigation of Different Topologies for Hybrid Fuel Cell Vehicles
The use of green energy has increased day by day. Environmentally friendly hybrid electric vehicles with low CO2 emissions have gained public attention. However, most battery electric vehicles are still having range problems, and emission values of hybrid electric vehicles are still not at the desired levels. Thus, fuel cell vehicles have gained some attention as good alternatives. The primary energy source for these vehicles is fuel cells, which are used in conjunction with batteries and supercapacitors to increase system performance. The combination of fuel cell + battery, fuel cell + supercapacitor, and fuel cell + battery + supercapacitor systems are currently the most popular topologies in this technology. The performance of these topologies is related to the overall energy efficiency and exergy efficiency of the vehicle model. Energy and exergy are two basic terminologies used to determine system performance and quality. Exergy determines the thermodynamic losses that cannot be determined using energy formulations alone. Thereby, it is very important to use both terminologies together to examine the performance of topologies and to determine any system losses. For this purpose, in this study, fuel cell + battery, fuel cell + supercapacitor, and fuel cell + battery + supercapacitor topologies were prepared and applied for Urban Dynamometer Driving Schedule (UDDS), Highway Fuel Economy Test Cycle (HWFET), New European Driving Cycle (NEDC), and Federal Test Procedure (FTP) driving cycles. Comparisons of these topologies in fuel consumption, power performance, and energy and exergy efficiencies were performed for the driving cycles. Also, energy flow, during the driving cycle, has showed and interpreted for the fuel cell vehicle that is designed and analyzed.
- 3 February 2023
- Published by Hindawi Limited in International Journal of Energy Research
- Vol. 2023, 1-16
Open AccessEnergetic and Exergetic Performance Investigation of Different Topologies for Hybrid Fuel Cell Vehicles
The use of green energy has increased day by day. Environmentally friendly hybrid electric vehicles with low CO2 emissions have gained public attention. However, most battery electric vehicles are still having range problems, and emission values of hybrid electric vehicles are still not at the desired levels. Thus, fuel cell vehicles have gained some attention as good alternatives. The primary energy source for these vehicles is fuel cells, which are used in conjunction with batteries and supercapacitors to increase system performance. The combination of fuel cell + battery, fuel cell + supercapacitor, and fuel cell + battery + supercapacitor systems are currently the most popular topologies in this technology. The performance of these topologies is related to the overall energy efficiency and exergy efficiency of the vehicle model. Energy and exergy are two basic terminologies used to determine system performance and quality. Exergy determines the thermodynamic losses that cannot be determined using energy formulations alone. Thereby, it is very important to use both terminologies together to examine the performance of topologies and to determine any system losses. For this purpose, in this study, fuel cell + battery, fuel cell + supercapacitor, and fuel cell + battery + supercapacitor topologies were prepared and applied for Urban Dynamometer Driving Schedule (UDDS), Highway Fuel Economy Test Cycle (HWFET), New European Driving Cycle (NEDC), and Federal Test Procedure (FTP) driving cycles. Comparisons of these topologies in fuel consumption, power performance, and energy and exergy efficiencies were performed for the driving cycles. Also, energy flow, during the driving cycle, has showed and interpreted for the fuel cell vehicle that is designed and analyzed.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (4 Part A) , 2935-2946
Simulation and modeling of a solar-aided underground energy storage system
The significance of energy storage methods and related R and D studies are increasing due to the depletion of fossil fuels, rising energy prices, and growing environmental concerns. Storage of energy means elimination of practical concerns for the time difference between the time when the energy is produced and when it?s needed. The importance of producing and storing energy through renewable sources is increasing every day, especially in developing countries like Turkiye, as such countries would like to reduce their dependence on foreign sources. This study focuses on an underground thermal energy storage system that was modeled for Van Region, using M-file program. The performance of an isolated day heat system as a thermal energy storage was investigated, and the thermal energy storage capacity of the system was researched for a 5 m ? 5 m ? 5 m soil area located on the Van Yuzuncu Yil University Campus. The temperature distribution, heat loss, and efficiency calculations were performed for a complete year and 3-D representations of the findings were obtained. The lowest efficiencies were observed in May, while the highest efficiencies were observed in July. It was found that the maximum heat loss from the system took place during December and January, and the system could be easily and effectively become a heating source for a single household with the addition of a heat pump.
- 1 January 2023
- Published by National Library of Serbia in Thermal Science
- Vol. 27 (4 Part A) , 2935-2946
Open AccessSimulation and modeling of a solar-aided underground energy storage system
The significance of energy storage methods and related R and D studies are increasing due to the depletion of fossil fuels, rising energy prices, and growing environmental concerns. Storage of energy means elimination of practical concerns for the time difference between the time when the energy is produced and when it?s needed. The importance of producing and storing energy through renewable sources is increasing every day, especially in developing countries like Turkiye, as such countries would like to reduce their dependence on foreign sources. This study focuses on an underground thermal energy storage system that was modeled for Van Region, using M-file program. The performance of an isolated day heat system as a thermal energy storage was investigated, and the thermal energy storage capacity of the system was researched for a 5 m ? 5 m ? 5 m soil area located on the Van Yuzuncu Yil University Campus. The temperature distribution, heat loss, and efficiency calculations were performed for a complete year and 3-D representations of the findings were obtained. The lowest efficiencies were observed in May, while the highest efficiencies were observed in July. It was found that the maximum heat loss from the system took place during December and January, and the system could be easily and effectively become a heating source for a single household with the addition of a heat pump.
- 1 January 2021
- Published by MIM Research Group in Research on Engineering Structures and Materials
Analysis of various flow field designs for PEM fuel cells used in vehicular systems through 3D modelling
Analysis of various flow field designs for PEM fuel cells used in vehicular systems through 3D modelling
- 1 January 2021
- Published by MIM Research Group in Research on Engineering Structures and Materials
Analysis of various flow field designs for PEM fuel cells used in vehicular systems through 3D modelling
Analysis of various flow field designs for PEM fuel cells used in vehicular systems through 3D modelling
- 21 December 2020
- Published by Kyrgyz-Turkish Manas University in MANAS Journal of Engineering
- Vol. 8 (2) , 106-114
Modelling, Sensitivity and Exergy Analysis of Triple-Pressure Heat Recovery Steam Generator
Combined with the increasing demand for environmental pollution and electrical energy, combined cycle power plant power plants are increasingly important. It is necessary to increase the performance of power plants, reduce carbon emissions and increase energy production. Any change to the heat recovery steam generator design is an important component of the combined cycle power plant, as it directly affects the performance of the combined cycle power plant. This study describes the modeling, sensitivity and exergy analysis of a HRSG in a combined cycle power plant. Three-pressure HRSG was modeled with the Aspen Plus simulation program and sensitivity analysis was performed. At the same time, energy and exergy analyzes were made for each component in the combined cycle power plant.
- 21 December 2020
- Published by Kyrgyz-Turkish Manas University in MANAS Journal of Engineering
- Vol. 8 (2) , 106-114
Modelling, Sensitivity and Exergy Analysis of Triple-Pressure Heat Recovery Steam Generator
Combined with the increasing demand for environmental pollution and electrical energy, combined cycle power plant power plants are increasingly important. It is necessary to increase the performance of power plants, reduce carbon emissions and increase energy production. Any change to the heat recovery steam generator design is an important component of the combined cycle power plant, as it directly affects the performance of the combined cycle power plant. This study describes the modeling, sensitivity and exergy analysis of a HRSG in a combined cycle power plant. Three-pressure HRSG was modeled with the Aspen Plus simulation program and sensitivity analysis was performed. At the same time, energy and exergy analyzes were made for each component in the combined cycle power plant.
- Open Access
- 1 September 2019
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 22 (3) , 159-166
Exergetic Comparison of Various Flow Patterns in PEMFCs
Energy need of the civilized world is ever increasing, and as such, the subject of energy production from renewable energy sources is gaining popularity in scientific studies. Amongst these studies are the researches on fuel cell systems. In this study, the flow channels of the “proton exchange membrane” (PEM) type fuel cell were designed, modelled, and studies were conducted on three-dimensional channels of various designs via Comsol Multiphysics simulation software, with hopes to contribute to the renewable energy solutions. Proposed fuel cell designs and geometries of flow channels were compared to existing fuel cells’ with exergetically efficient designs, in terms of total exergy efficiency. Exergy efficiency analysis was conducted on the membrane surfaces of the proposed flow channels. Anode and cathode side exergy analyses, polarization curve of the system, voltage, current and produced power parameter results were also inspected.
- 1 September 2019
- Published by International Centre for Applied Thermodynamics (ICAT) in International Journal of Thermodynamics
- Vol. 22 (3) , 159-166
Open AccessExergetic Comparison of Various Flow Patterns in PEMFCs
Energy need of the civilized world is ever increasing, and as such, the subject of energy production from renewable energy sources is gaining popularity in scientific studies. Amongst these studies are the researches on fuel cell systems. In this study, the flow channels of the “proton exchange membrane” (PEM) type fuel cell were designed, modelled, and studies were conducted on three-dimensional channels of various designs via Comsol Multiphysics simulation software, with hopes to contribute to the renewable energy solutions. Proposed fuel cell designs and geometries of flow channels were compared to existing fuel cells’ with exergetically efficient designs, in terms of total exergy efficiency. Exergy efficiency analysis was conducted on the membrane surfaces of the proposed flow channels. Anode and cathode side exergy analyses, polarization curve of the system, voltage, current and produced power parameter results were also inspected.
- 1 November 2018
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 43 (48) , 21886-21898
A complementary study on novel PdAuCo catalysts: Synthesis, characterization, direct formic acid fuel cell application, and exergy analysis
- 1 November 2018
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 43 (48) , 21886-21898
A complementary study on novel PdAuCo catalysts: Synthesis, characterization, direct formic acid fuel cell application, and exergy analysis
- 5 August 2018
- Published by Springer Nature
- p. 969-982
Exergetic Simulation and Performance Assessment of 1–1 Shell and Tube Heat Exchangers
- 5 August 2018
- Published by Springer Nature
- p. 969-982
Exergetic Simulation and Performance Assessment of 1–1 Shell and Tube Heat Exchangers
- 5 August 2018
- Published by Springer Nature
- p. 983-994
Parametric Exergetic Investigation of a Direct Formic Acid Fuel Cell System
- 5 August 2018
- Published by Springer Nature
- p. 983-994
Parametric Exergetic Investigation of a Direct Formic Acid Fuel Cell System
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Exergy
- Vol. 22 (2) , 125
Exergetic performance analysis of a solar power system (SPS) in a high plateau
In this study, a comprehensive exergy analysis was applied to a solar power system (SPS) located in the city of Van, Turkey. Van was always known as a sun city throughout history with the name of TUŞBA. It has an average of 300 sunny days a year, an altitude of 1727 m, and an average daily temperature of 9.85°C. Considering how the need for sustainable and renewable energy sources - and knowledge over them - constantly increases, this SPS was built to reveal the true solar potential of the campus area of Yuzuncu Yıl University of the city of Van, hopefully as a precursor for further large-scale SPS constructions in the region. A daily analysis considering energy production and global radiation was applied to the system in 2013 for 365 days. It was found that the yearly exergy efficiency of the system was 10% and total electrical energy production was 31,038.95 kWh, averaging 1763.5 kWh/kWp yearly.
- 1 January 2017
- Published by Inderscience Publishers in International Journal of Exergy
- Vol. 22 (2) , 125
Exergetic performance analysis of a solar power system (SPS) in a high plateau
In this study, a comprehensive exergy analysis was applied to a solar power system (SPS) located in the city of Van, Turkey. Van was always known as a sun city throughout history with the name of TUŞBA. It has an average of 300 sunny days a year, an altitude of 1727 m, and an average daily temperature of 9.85°C. Considering how the need for sustainable and renewable energy sources - and knowledge over them - constantly increases, this SPS was built to reveal the true solar potential of the campus area of Yuzuncu Yıl University of the city of Van, hopefully as a precursor for further large-scale SPS constructions in the region. A daily analysis considering energy production and global radiation was applied to the system in 2013 for 365 days. It was found that the yearly exergy efficiency of the system was 10% and total electrical energy production was 31,038.95 kWh, averaging 1763.5 kWh/kWp yearly.