Thomas P. Weldon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thomas P. Weldon has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
Ryan S. Adams
Department of Electrical and Computer Engineering, University of North Carolina at Charlotte, Charlotte, NC, USA
26 shared publicationsJohn M. C. Covington
University of North Carolina at Charlotte, Dept. of Electrical and Computer Eng., 9201 Univ. City Blvd., Charlotte, NC, 28223, USA
12 shared publicationsJoshua W. Shehan
University of North Carolina at Charlotte, Charlotte, NC, 28223
10 shared publicationsKathryn L. Smith
Department of Electrical and Computer Engineering, University of North Carolina at Charlotte, USA
10 shared publicationsVarun S. Kshatri
Department of Electrical and Computer Engineering, University of North Carolina at Charlotte, USA
9 shared publicationsKasra Daneshvar
Department of Electrical and Computer Engineering, University of North Carolina at Charlotte, USA
7 shared publications
Latest Publications
- Open Access
- 12 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Circuits and Systems
- Vol. 3, 109-114
A Stable Digital Impedance Circuit Design Method for Resistive Source Impedances
The recent discovery that the input impedance of digital impedance circuits is dependent on the external source impedance requires the development of new design procedures to address the significant complexity of this discovery. These circuits are of particular utility for the implementation of difficult non-Foster impedances such as negative capacitance. Therefore, a new digital impedance circuit design procedure is presented where stable digital filter coefficients are computed to provide desired digital impedance values at two chosen frequencies, given that a stable solution exists. The new design procedure explicitly addresses the aforementioned dependence on the external source impedance for digital impedance circuits with resistive sources. Lastly, simulation results from a negative capacitance design example are compared to the new theory to confirm the efficacy of the new design procedure.
- 12 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Circuits and Systems
- Vol. 3, 109-114
Open AccessA Stable Digital Impedance Circuit Design Method for Resistive Source Impedances
The recent discovery that the input impedance of digital impedance circuits is dependent on the external source impedance requires the development of new design procedures to address the significant complexity of this discovery. These circuits are of particular utility for the implementation of difficult non-Foster impedances such as negative capacitance. Therefore, a new digital impedance circuit design procedure is presented where stable digital filter coefficients are computed to provide desired digital impedance values at two chosen frequencies, given that a stable solution exists. The new design procedure explicitly addresses the aforementioned dependence on the external source impedance for digital impedance circuits with resistive sources. Lastly, simulation results from a negative capacitance design example are compared to the new theory to confirm the efficacy of the new design procedure.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1545-1546
Observed Q and Gravitationally-Small Antenna Behavior of a Binary Black Hole Radiator
Recent theoretical advances have provided an analytical expression for the Q of gravitationally-small sources of gravitational radiation, along lines similar to the Wheeler-Chu limit for electrically-small antennas. This paper presents the first published results using this new theory to analyze the Q of a black-hole inspiral, using observed transient gravitational wave data from the GW170608 black-hole merger. Despite the astronomical scale of a radiation source comprised of two black holes having upwards of 7 solar masses each, the GW170608 binary black hole is shown to be a gravitationally-small high-Q radiator at the very low frequencies of the gravitational waves.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1545-1546
Observed Q and Gravitationally-Small Antenna Behavior of a Binary Black Hole Radiator
Recent theoretical advances have provided an analytical expression for the Q of gravitationally-small sources of gravitational radiation, along lines similar to the Wheeler-Chu limit for electrically-small antennas. This paper presents the first published results using this new theory to analyze the Q of a black-hole inspiral, using observed transient gravitational wave data from the GW170608 black-hole merger. Despite the astronomical scale of a radiation source comprised of two black holes having upwards of 7 solar masses each, the GW170608 binary black hole is shown to be a gravitationally-small high-Q radiator at the very low frequencies of the gravitational waves.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Search-Based Design of Digital Non-Foster Antenna Match for High-Speed Low-Impedance Converters
Previous design procedures for low-frequency digital non-Foster circuits are most effective when high input impedance analog-to-digital converters are employed. However, these earlier design methods did not include the effects of potentially low impedances of high-frequency converters that may be required for antenna impedance matching. Therefore, we present a new search-based design procedure for digital non-Foster antennamatching circuits using low-impedance converters. An example of the new design method is presented, with simulation results showing effective impedance matching of a 10 MHz electrically-small antenna using a digital non-Foster circuit and a low-impedance converter.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Search-Based Design of Digital Non-Foster Antenna Match for High-Speed Low-Impedance Converters
Previous design procedures for low-frequency digital non-Foster circuits are most effective when high input impedance analog-to-digital converters are employed. However, these earlier design methods did not include the effects of potentially low impedances of high-frequency converters that may be required for antenna impedance matching. Therefore, we present a new search-based design procedure for digital non-Foster antennamatching circuits using low-impedance converters. An example of the new design method is presented, with simulation results showing effective impedance matching of a 10 MHz electrically-small antenna using a digital non-Foster circuit and a low-impedance converter.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Measurement of a digital non-Foster negative RLC circuit and digital positive RLC circuit
Measurements and theory are presented for digital discrete-time implementations of series non-Foster negative RLC (resistor-inductor-capacitor) circuits and series positive RLC circuits. This new digital RLC design approach builds upon recent digital implementations of other non-Foster circuits such as negative RC (resistor-capacitor) and negative RL (resistor-inductor) circuits. Such digital implementations of non-Foster circuits have shown promise in addressing common design challenges, such as stability, that may be more difficult to control in analog non-Foster circuits. Furthermore, a digital approach offers inherent potential advantages in applications such as software-tunable or adaptive digital implementations of negative RLC or positive RLC circuits. To confirm the proposed approach and underlying theory, simulation results and prototype measurements are provided that demonstrate the efficacy of digital implementations of both positive RLC and negative RLC circuits.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Measurement of a digital non-Foster negative RLC circuit and digital positive RLC circuit
Measurements and theory are presented for digital discrete-time implementations of series non-Foster negative RLC (resistor-inductor-capacitor) circuits and series positive RLC circuits. This new digital RLC design approach builds upon recent digital implementations of other non-Foster circuits such as negative RC (resistor-capacitor) and negative RL (resistor-inductor) circuits. Such digital implementations of non-Foster circuits have shown promise in addressing common design challenges, such as stability, that may be more difficult to control in analog non-Foster circuits. Furthermore, a digital approach offers inherent potential advantages in applications such as software-tunable or adaptive digital implementations of negative RLC or positive RLC circuits. To confirm the proposed approach and underlying theory, simulation results and prototype measurements are provided that demonstrate the efficacy of digital implementations of both positive RLC and negative RLC circuits.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Measurement of a clock-tuned digital non-Foster circuit for positive or negative digital capacitance
Theory and measured results are presented for a clock-tuned digital capacitor that provides digital implementation of a variable non-Foster negative capacitance or a variable positive capacitance. Unlike previous digital non-Foster capacitor designs, the proposed approach provides a variable capacitance without requiring changes to the signal processing hardware or embedded software. Instead, a single external clock provides simple control of the variable negative or positive capacitance of the circuit. Theoretical results are provided showing that predicted digital capacitance is inversely proportional to clock frequency, and associated parasitic resistance is determined by design parameters. Simulation results and prototype measurements confirm the underlying theory, and demonstrate the efficacy of the proposed approach.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Measurement of a clock-tuned digital non-Foster circuit for positive or negative digital capacitance
Theory and measured results are presented for a clock-tuned digital capacitor that provides digital implementation of a variable non-Foster negative capacitance or a variable positive capacitance. Unlike previous digital non-Foster capacitor designs, the proposed approach provides a variable capacitance without requiring changes to the signal processing hardware or embedded software. Instead, a single external clock provides simple control of the variable negative or positive capacitance of the circuit. Theoretical results are provided showing that predicted digital capacitance is inversely proportional to clock frequency, and associated parasitic resistance is determined by design parameters. Simulation results and prototype measurements confirm the underlying theory, and demonstrate the efficacy of the proposed approach.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Investigation of an adaptively-tuned digital non-Foster approach for impedance matching of electrically-small antennas
An adaptively-tuned digital non-Foster negative capacitor is investigated for impedance matching of electrically-small antennas. Such a digital non-Foster approach has the potential to address difficult design challenges such as stability and tolerance issues in analog non-Foster circuits. Furthermore, the digital non-Foster approach is tunable in software. The required negative capacitance is implemented using an ADC (analog-to-digital converter), DAC (digital-to-analog converter), and signal processing. In addition, the proposed adaptive approach uses the DAC and ADC to excite the antenna with a signal, and determine the antenna capacitance and resistance using impulse response and/or ARMA modeling. The digital non-Foster negative capacitance is then used to cancel the observed undesired reactance of the antenna. Results are given for an RC model of an electrically-short antenna that show effective estimation of impedance, and successful cancellation of most of the undesired reactance.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Investigation of an adaptively-tuned digital non-Foster approach for impedance matching of electrically-small antennas
An adaptively-tuned digital non-Foster negative capacitor is investigated for impedance matching of electrically-small antennas. Such a digital non-Foster approach has the potential to address difficult design challenges such as stability and tolerance issues in analog non-Foster circuits. Furthermore, the digital non-Foster approach is tunable in software. The required negative capacitance is implemented using an ADC (analog-to-digital converter), DAC (digital-to-analog converter), and signal processing. In addition, the proposed adaptive approach uses the DAC and ADC to excite the antenna with a signal, and determine the antenna capacitance and resistance using impulse response and/or ARMA modeling. The digital non-Foster negative capacitance is then used to cancel the observed undesired reactance of the antenna. Results are given for an RC model of an electrically-short antenna that show effective estimation of impedance, and successful cancellation of most of the undesired reactance.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Stability analysis and measurement of RC and RL digital non-Foster circuits with latency
Stability analysis and measurements are presented for negative capacitance and negative inductance designs of digital non-Foster circuits that include a series resistance and model the effects of latency. Such digital non-Foster circuits provide a new important alternative to analog non-Foster circuits, with potential to address stability and performance issues in important non-Foster application areas such as metamaterials, acoustic cloaking, and electrically-small antennas. The proposed approach includes a resistive component in the signal processing of digital non-Foster RC and RL circuits to help control stability and to mitigate parasitic resistance, and also includes latency effects associated with computation and conversion time. Analysis, simulation, and measured results confirm the desired non-Foster impedances, and show useful regions of stability as a function of resistance and latency.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Stability analysis and measurement of RC and RL digital non-Foster circuits with latency
Stability analysis and measurements are presented for negative capacitance and negative inductance designs of digital non-Foster circuits that include a series resistance and model the effects of latency. Such digital non-Foster circuits provide a new important alternative to analog non-Foster circuits, with potential to address stability and performance issues in important non-Foster application areas such as metamaterials, acoustic cloaking, and electrically-small antennas. The proposed approach includes a resistive component in the signal processing of digital non-Foster RC and RL circuits to help control stability and to mitigate parasitic resistance, and also includes latency effects associated with computation and conversion time. Analysis, simulation, and measured results confirm the desired non-Foster impedances, and show useful regions of stability as a function of resistance and latency.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A digital non-Foster fast-wave line using an Internet of Things approach for software tuning of multiple digital negative capacitors
A software-tunable digital non-Foster fast-wave transmission line is presented, using an Internet of Things approach to implement tuning and signal monitoring. Such non-Foster fast-wave lines offer greater bandwidth than conventional passive designs, and a digital non-Foster approach is proposed to provide a software-adjustable implementation of the required negative capacitors. Further, an IoT (Internet-of-Things) approach is employed, where multiple non-Foster circuit elements are controlled over Ethernet by a laptop graphical user interface, including remote signal monitoring. This IoT approach has the advantage of being readily extended to accommodate more devices or multidimensional arrays. Measured data is presented for an IoT-based prototype of a superluminal digital non-Foster fast-wave line with software-tunable negative capacitance.
- 1 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
A digital non-Foster fast-wave line using an Internet of Things approach for software tuning of multiple digital negative capacitors
A software-tunable digital non-Foster fast-wave transmission line is presented, using an Internet of Things approach to implement tuning and signal monitoring. Such non-Foster fast-wave lines offer greater bandwidth than conventional passive designs, and a digital non-Foster approach is proposed to provide a software-adjustable implementation of the required negative capacitors. Further, an IoT (Internet-of-Things) approach is employed, where multiple non-Foster circuit elements are controlled over Ethernet by a laptop graphical user interface, including remote signal monitoring. This IoT approach has the advantage of being readily extended to accommodate more devices or multidimensional arrays. Measured data is presented for an IoT-based prototype of a superluminal digital non-Foster fast-wave line with software-tunable negative capacitance.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 731-732
Effects of latency and quantization noise on digital discrete-time non-Foster circuits
Digital discrete-time implementations of non-Foster circuit elements offer an alternative approach to the design of devices such as negative capacitors and negative inductors. However, practical implementations of high-speed digital non-Foster circuits are affected by latency and noise, where latency can arise from analog-to-digital conversion time and computation time. Thus, the present work explores the impact of latency and quantization noise on digital non-Foster circuits. Simulation results for a digital negative capacitor show useful performance can be obtained, even with latencies as large as one conversion clock cycle. In addition, quantization noise effects in digital non-Foster circuits are considered.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 731-732
Effects of latency and quantization noise on digital discrete-time non-Foster circuits
Digital discrete-time implementations of non-Foster circuit elements offer an alternative approach to the design of devices such as negative capacitors and negative inductors. However, practical implementations of high-speed digital non-Foster circuits are affected by latency and noise, where latency can arise from analog-to-digital conversion time and computation time. Thus, the present work explores the impact of latency and quantization noise on digital non-Foster circuits. Simulation results for a digital negative capacitor show useful performance can be obtained, even with latencies as large as one conversion clock cycle. In addition, quantization noise effects in digital non-Foster circuits are considered.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 193-194
Measurement of a fast-wave line using digital non-Foster circuits for software-adjustable delay
Measured results are compared to simulation results for a wideband software-adjustable fast-wave line using coaxial line sections loaded with digital discrete-time non-Foster circuit elements. In the proposed approach, the negative capacitance of non-Foster circuit elements is varied by changing the signal processing in the digital non-Foster circuit. For the purposes of demonstration and comparison with analog non-Foster approaches, a prototype three-stage fast-wave coaxial line is implemented using three digital negative capacitors. Group delay is shown to be less than in corresponding vacuum propagation, and group delay is shown to be adjustable in software with varied negative capacitance. Measured and simulated results are in good agreement, and closely resemble a frequency-scaled version of prior fast-wave results for analog non-Foster loaded waveguide at higher frequency.
- 27 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 193-194
Measurement of a fast-wave line using digital non-Foster circuits for software-adjustable delay
Measured results are compared to simulation results for a wideband software-adjustable fast-wave line using coaxial line sections loaded with digital discrete-time non-Foster circuit elements. In the proposed approach, the negative capacitance of non-Foster circuit elements is varied by changing the signal processing in the digital non-Foster circuit. For the purposes of demonstration and comparison with analog non-Foster approaches, a prototype three-stage fast-wave coaxial line is implemented using three digital negative capacitors. Group delay is shown to be less than in corresponding vacuum propagation, and group delay is shown to be adjustable in software with varied negative capacitance. Measured and simulated results are in good agreement, and closely resemble a frequency-scaled version of prior fast-wave results for analog non-Foster loaded waveguide at higher frequency.