Steven T. Weinman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Steven T. Weinman has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Christoffer Heath Turner
The University of Alabama
5 shared publications - Lauren M. Ward
Department of Chemical and Biological Engineering, The University of Alabama, Tuscaloosa, AL 35487, USA
4 shared publications - Jason Edward Bara
Department of Chemical & Biological Engineering, The University of Alabama, Tuscaloosa, AL, 35487-0203 USA
3 shared publications Scott M. Husson
3 shared publications- Hadi Rouhi
Materials Engineering And Nanosensor [MEAN] Laboratory, Department of Chemical and Biological Engineering The University of Alabama Tuscaloosa Alabama USA
2 shared publications - Joseph T. Danner
Dept. of Chemical and Biological Engineering
2 shared publications
Latest Publications
- 23 October 2026
- Published by Elsevier in Journal of Membrane Science
- Vol. 762
Engineering surfactant-assisted molecularly regulated interfacial polymerization for polyamide reverse osmosis membranes
- 23 October 2026
- Published by Elsevier in Journal of Membrane Science
- Vol. 762
Engineering surfactant-assisted molecularly regulated interfacial polymerization for polyamide reverse osmosis membranes
- Open Access
- 1 October 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (10) , 105065
Emulsion additives for improved yield stress in magnetorheological fluids
Magnetorheological emulsions (MREms) are field-responsive materials that combine the tunable morphology of emulsions with the controllable yielding behavior of magnetorheological fluids (MRFs). In this work, effects of droplet size, dispersed-phase composition, size dispersity, continuous-phase rheology, and magnetic particle concentration on MREm yield stress were investigated. Emulsion behavior was interpreted through a modified Mason number incorporating capillary number and viscosity ratio. In situ microscopy and particle tracking velocimetry were used to examine emulsion–iron chain interactions under magnetic field and shear. Yield stress depended on interactions between magnetic particle structuring, droplet deformation, internal circulation, and interfacial stress transmission. Droplet size effects were dependent on dispersed-phase properties, showing droplet geometry alone is insufficient to describe MREm rheology. Modification of the continuous phase with sodium alginate showed shear-thinning influenced yielding more than viscosity magnitude. Furthermore, high-dispersity emulsions exhibited higher yield stresses than membrane-emulsified systems, indicating that surfactant availability and interfacial viscoelasticity govern yielding more than droplet size distribution. Increasing magnetic particle concentration reduced emulsion-mediated effects as magnetic interactions became dominant. These findings establish interfacial rheology, continuous-phase rheology, and emulsion damping as design parameters for tailoring magnetorheological response and engineering MREms with higher yield stress than comparable MRFs for adaptive damping and vibration-control applications.
- 1 October 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (10) , 105065
Open AccessEmulsion additives for improved yield stress in magnetorheological fluids
Magnetorheological emulsions (MREms) are field-responsive materials that combine the tunable morphology of emulsions with the controllable yielding behavior of magnetorheological fluids (MRFs). In this work, effects of droplet size, dispersed-phase composition, size dispersity, continuous-phase rheology, and magnetic particle concentration on MREm yield stress were investigated. Emulsion behavior was interpreted through a modified Mason number incorporating capillary number and viscosity ratio. In situ microscopy and particle tracking velocimetry were used to examine emulsion–iron chain interactions under magnetic field and shear. Yield stress depended on interactions between magnetic particle structuring, droplet deformation, internal circulation, and interfacial stress transmission. Droplet size effects were dependent on dispersed-phase properties, showing droplet geometry alone is insufficient to describe MREm rheology. Modification of the continuous phase with sodium alginate showed shear-thinning influenced yielding more than viscosity magnitude. Furthermore, high-dispersity emulsions exhibited higher yield stresses than membrane-emulsified systems, indicating that surfactant availability and interfacial viscoelasticity govern yielding more than droplet size distribution. Increasing magnetic particle concentration reduced emulsion-mediated effects as magnetic interactions became dominant. These findings establish interfacial rheology, continuous-phase rheology, and emulsion damping as design parameters for tailoring magnetorheological response and engineering MREms with higher yield stress than comparable MRFs for adaptive damping and vibration-control applications.
- Open Access
- 12 August 2026
- Published by Frontiers Media SA in Frontiers in Membrane Science and Technology
- Vol. 5, 1892716
Primary, secondary, tertiary, and quaternary Alkyl amine-functionalized PVDF membranes for DBSA removal
Water remediation has become increasingly critical over recent decades due to the growing discharge of surfactant-containing wastewater into the environment. Dodecylbenzene sulfonic acid (DBSA), a widely used detergent, presents significant challenges for water treatment because of its high solubility and chemical stability. To address this challenge, polyvinylidene difluoride (PVDF) membranes were functionalized with three types of diamines; primary (P), secondary (S), and tertiary (T); followed by quaternization of the tertiary diamine-modified membrane to obtain a quaternary-modified variant (Q). The modification likely occurred via diamine (base)-driven dehydrofluorination creating polyene segments which were partially modified by the diamines via a Michael addition. These membranes were employed to adsorb the negatively charged DBSA molecules, and their adsorption performance was systematically compared. Initial surface characterization using ATR-FTIR, XPS, water contact angle, and SEM indicated successful modification for all membranes. Performance tests of P, S, and T membranes demonstrated DBSA removal efficiencies of 93.1%, 91.4%, and 95.3% from a ∼600 mg/L solution within 3 h of contact time. Q membranes showed a lower DBSA removal of 37.3% at 3 h, which increased to 72.1% at 24 h. The membranes exhibited enhanced adsorption capacities of up to 21.6 mg/g, with adsorption strongly influenced by solution pH due to protonation-driven electrostatic interactions. Kinetic analysis revealed that DBSA adsorption followed pseudo-second-order kinetics for P, S, and Q membrane and pseudo-first-order kinetics for T membrane. The isotherm studies showed the Temkin model provided the best fit, indicating heterogeneous surface interactions and predominantly physisorption-driven adsorption. Thermodynamic and isosteric analyses further confirmed the exothermic nature of DBSA adsorption, with enthalpy values ranging from ∼2.1 to 25.4 kJ/ mol and a decrease in adsorption favorability at elevated temperatures. All the modified membranes showed promising regeneration results, with P, S, T, and Q membranes having 86.6%, 88.8%, 87.4%, and 72.0% removal in first cycle and 69.9%, 68.6%, 70.6%, and 72.0% removal in fifth cycle. This study demonstrates that amine functionality influences surface chemistry and DBSA adsorption behavior and highlights the potential of amine-functionalized PVDF membranes as promising adsorptive materials for the efficient removal of harmful anionic surfactants from contaminated water systems.
- 12 August 2026
- Published by Frontiers Media SA in Frontiers in Membrane Science and Technology
- Vol. 5, 1892716
Open AccessPrimary, secondary, tertiary, and quaternary Alkyl amine-functionalized PVDF membranes for DBSA removal
Water remediation has become increasingly critical over recent decades due to the growing discharge of surfactant-containing wastewater into the environment. Dodecylbenzene sulfonic acid (DBSA), a widely used detergent, presents significant challenges for water treatment because of its high solubility and chemical stability. To address this challenge, polyvinylidene difluoride (PVDF) membranes were functionalized with three types of diamines; primary (P), secondary (S), and tertiary (T); followed by quaternization of the tertiary diamine-modified membrane to obtain a quaternary-modified variant (Q). The modification likely occurred via diamine (base)-driven dehydrofluorination creating polyene segments which were partially modified by the diamines via a Michael addition. These membranes were employed to adsorb the negatively charged DBSA molecules, and their adsorption performance was systematically compared. Initial surface characterization using ATR-FTIR, XPS, water contact angle, and SEM indicated successful modification for all membranes. Performance tests of P, S, and T membranes demonstrated DBSA removal efficiencies of 93.1%, 91.4%, and 95.3% from a ∼600 mg/L solution within 3 h of contact time. Q membranes showed a lower DBSA removal of 37.3% at 3 h, which increased to 72.1% at 24 h. The membranes exhibited enhanced adsorption capacities of up to 21.6 mg/g, with adsorption strongly influenced by solution pH due to protonation-driven electrostatic interactions. Kinetic analysis revealed that DBSA adsorption followed pseudo-second-order kinetics for P, S, and Q membrane and pseudo-first-order kinetics for T membrane. The isotherm studies showed the Temkin model provided the best fit, indicating heterogeneous surface interactions and predominantly physisorption-driven adsorption. Thermodynamic and isosteric analyses further confirmed the exothermic nature of DBSA adsorption, with enthalpy values ranging from ∼2.1 to 25.4 kJ/ mol and a decrease in adsorption favorability at elevated temperatures. All the modified membranes showed promising regeneration results, with P, S, T, and Q membranes having 86.6%, 88.8%, 87.4%, and 72.0% removal in first cycle and 69.9%, 68.6%, 70.6%, and 72.0% removal in fifth cycle. This study demonstrates that amine functionality influences surface chemistry and DBSA adsorption behavior and highlights the potential of amine-functionalized PVDF membranes as promising adsorptive materials for the efficient removal of harmful anionic surfactants from contaminated water systems.
- 10 December 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 80
Biocatalytic membrane for the degradation of diisononyl phthalate
- 10 December 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 80
Biocatalytic membrane for the degradation of diisononyl phthalate
- 24 November 2025
- Published by Royal Society of Chemistry (RSC) in Molecular Systems Design & Engineering
- Vol. 10 (12) , 1028-1033
Serinol as a tunable and sustainable framework for high capacity, low viscosity, water-lean CO 2 capture and switchable solvents
Diethers of serinol are low-viscosity liquids with tunable properties and scalable syntheses for water-lean CO 2 capture and switchable solvent applications.
- 24 November 2025
- Published by Royal Society of Chemistry (RSC) in Molecular Systems Design & Engineering
- Vol. 10 (12) , 1028-1033
Serinol as a tunable and sustainable framework for high capacity, low viscosity, water-lean CO 2 capture and switchable solvents
Diethers of serinol are low-viscosity liquids with tunable properties and scalable syntheses for water-lean CO 2 capture and switchable solvent applications.
- 5 August 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Investigating the Molecular-Level Influence of Surfactants on Polyamide Reverse Osmosis Membrane Formation
Most thin-film composite reverse osmosis (RO) membranes are formed via interfacial polymerization (IP) between m-phenylenediamine (MPD) and trimesoyl chloride (TMC), yet controlling their structure and selectivity remains challenging. Surfactants can regulate this process, highlighting the need to understand the factors behind MPD transport and its interactions with surfactants. In this study, we provide a detailed molecular-level analysis by first conducting electronic structure calculations to investigate 17 surfactant/counterion combinations. Based on binding energies and partition coefficients, we select four surfactants for further interfacial MD simulations and eventually examine two surfactants in TMC-MPD cross-linking simulations, followed by structural characterization of the polymer membranes. Our results identify key molecular factors influencing membrane synthesis: electrostatic interactions (which affect surfactant binding energy with MPD and their orientation) and MPD partitioning into the organic phase (which impacts its stability at the interface). These factors dictate void connectivity through the membrane and may influence membrane performance, e.g., water permeance.
- 5 August 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Investigating the Molecular-Level Influence of Surfactants on Polyamide Reverse Osmosis Membrane Formation
Most thin-film composite reverse osmosis (RO) membranes are formed via interfacial polymerization (IP) between m-phenylenediamine (MPD) and trimesoyl chloride (TMC), yet controlling their structure and selectivity remains challenging. Surfactants can regulate this process, highlighting the need to understand the factors behind MPD transport and its interactions with surfactants. In this study, we provide a detailed molecular-level analysis by first conducting electronic structure calculations to investigate 17 surfactant/counterion combinations. Based on binding energies and partition coefficients, we select four surfactants for further interfacial MD simulations and eventually examine two surfactants in TMC-MPD cross-linking simulations, followed by structural characterization of the polymer membranes. Our results identify key molecular factors influencing membrane synthesis: electrostatic interactions (which affect surfactant binding energy with MPD and their orientation) and MPD partitioning into the organic phase (which impacts its stability at the interface). These factors dictate void connectivity through the membrane and may influence membrane performance, e.g., water permeance.
- 7 June 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (24) , 12173-12184
Substituent Effects on the Desalination Performance of Six-Carbon Amines in Temperature Swing Solvent Extraction
- 7 June 2025
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 64 (24) , 12173-12184
Substituent Effects on the Desalination Performance of Six-Carbon Amines in Temperature Swing Solvent Extraction
- Open Access
- 20 May 2025
- Published by Elsevier in Journal of Membrane Science
- Vol. 731
Functionalizing polyethersulfone membranes: using NMR to avoid pitfalls when using UV-induced polymerization to 'graft from' surfaces
- 20 May 2025
- Published by Elsevier in Journal of Membrane Science
- Vol. 731
Open AccessFunctionalizing polyethersulfone membranes: using NMR to avoid pitfalls when using UV-induced polymerization to 'graft from' surfaces
- 22 February 2025
- Published by Elsevier in Current Opinion in Chemical Engineering
- Vol. 48
Membranes from upcycled waste plastics: current status, challenges, and future outlook
- 22 February 2025
- Published by Elsevier in Current Opinion in Chemical Engineering
- Vol. 48
Membranes from upcycled waste plastics: current status, challenges, and future outlook
- 28 October 2024
- Published by Elsevier in Journal of Membrane Science
- Vol. 715
Pattern size relative to oil droplet size effect on oil fouling in nanofiltration
- 28 October 2024
- Published by Elsevier in Journal of Membrane Science
- Vol. 715
Pattern size relative to oil droplet size effect on oil fouling in nanofiltration