Carlos Blanes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Carlos Blanes has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Correcher
Departamento de Ingeniería Mecánica y de Materiales, Universitat Politècnica de València
4 shared publications - Carlos Ricolfe-Viala
Instituto de Automática e Informática Industrial (ai2) , Universidad Politécnica de Valencia
4 shared publications - Jaime Martínez-Turégano
Ai2 Research Institute, Universitat Politècnica de València
3 shared publications - Pablo Gonzalez-Planells
Rural and Agri-Food Engineering Department, Universitat Politècnica de València, Camino de Vera s/n, 46022 Valencia, Spain
3 shared publications C. Ortiz
Universitat Politècnica de València
2 shared publicationsCoral Ortiz
2 shared publications
Latest Publications
- Open Access
- 30 August 2024
- Published by MDPI AG in Horticulturae
- Vol. 10 (9) , 930
Automated Tenderness Assessment of Okra Using Robotic Non-Destructive Sensing
The quality of okra is crucial in satisfying consumer expectations, and the tenderness of okra is an essential parameter in estimating its condition. However, the current methods for assessing okra tenderness are slow and prone to errors, necessitating the development of a better, non-destructive method. The objective of the present study is to develop and test a non-destructive robotic sensor for assessing okra freshness and tenderness. A total of 120 pods were divided into two sets and stored under different conditions: 60 pods were kept in a cold chamber for 24 h (considered tender), while the other 60 pods were stored at room temperature for two days. First, the samples were assessed non-destructively using the force sensor of a collaborative robot, where a jamming pad (with internal granular fill) was capable of adapting and copying the okra shapes while controlling its force deformation. Second, the okra pods were evaluated with the referenced destructive tests, as well as weight loss, compression, and puncture tests. In order to validate the differences in the tenderness of the two sets, a discriminant analysis was carried out to segregate the okra pods into the two categories according to the destructive variables, confirming the procedure which was followed to produce tender and non-tender okra pods. After the differences in the tenderness of the two sets were confirmed, the variables extracted from the robotic sensor (maximum force (Fmax), first slope (S1), second slope (S2), the first overshoot (Os), and the steady state (Ss)) were significant predictors for the separation in the two quality categories. Discriminant analysis and logistic regression methods were applied to classify the pods into the two tenderness categories. Promising results were obtained using neural network classification with 80% accuracy in predicting tenderness from the sensor data, and a 95.5% accuracy rate was achieved in distinguishing between tender and non-tender okra pods in the validation data set. The use of the robotic sensor could be an efficient tool in evaluating the quality of okra. This process may lead to substantial savings and waste reduction, particularly considering the elevated cost and challenges associated with transporting perishable vegetables.
- 30 August 2024
- Published by MDPI AG in Horticulturae
- Vol. 10 (9) , 930
Open AccessAutomated Tenderness Assessment of Okra Using Robotic Non-Destructive Sensing
The quality of okra is crucial in satisfying consumer expectations, and the tenderness of okra is an essential parameter in estimating its condition. However, the current methods for assessing okra tenderness are slow and prone to errors, necessitating the development of a better, non-destructive method. The objective of the present study is to develop and test a non-destructive robotic sensor for assessing okra freshness and tenderness. A total of 120 pods were divided into two sets and stored under different conditions: 60 pods were kept in a cold chamber for 24 h (considered tender), while the other 60 pods were stored at room temperature for two days. First, the samples were assessed non-destructively using the force sensor of a collaborative robot, where a jamming pad (with internal granular fill) was capable of adapting and copying the okra shapes while controlling its force deformation. Second, the okra pods were evaluated with the referenced destructive tests, as well as weight loss, compression, and puncture tests. In order to validate the differences in the tenderness of the two sets, a discriminant analysis was carried out to segregate the okra pods into the two categories according to the destructive variables, confirming the procedure which was followed to produce tender and non-tender okra pods. After the differences in the tenderness of the two sets were confirmed, the variables extracted from the robotic sensor (maximum force (Fmax), first slope (S1), second slope (S2), the first overshoot (Os), and the steady state (Ss)) were significant predictors for the separation in the two quality categories. Discriminant analysis and logistic regression methods were applied to classify the pods into the two tenderness categories. Promising results were obtained using neural network classification with 80% accuracy in predicting tenderness from the sensor data, and a 95.5% accuracy rate was achieved in distinguishing between tender and non-tender okra pods in the validation data set. The use of the robotic sensor could be an efficient tool in evaluating the quality of okra. This process may lead to substantial savings and waste reduction, particularly considering the elevated cost and challenges associated with transporting perishable vegetables.
- Open Access
- 4 July 2024
- Published by MDPI AG in Preprints.org
Automated Tenderness Assessment of Okra Using Robotic Non-Destructive Sensing
Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.
- 4 July 2024
- Published by MDPI AG in Preprints.org
Open AccessAutomated Tenderness Assessment of Okra Using Robotic Non-Destructive Sensing
Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.
- Open Access
- 19 January 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (2) , 881
Operation of DR–HVdc-Connected Grid-Forming Wind Turbine Converters Using Robust Loop-Shaping Controllers
Off-shore wind power plants can be connected to the on-shore grid using diode rectifier HVdc links. As diode rectifiers are passive converters, off-shore WPPs require grid-forming capability. This paper shows how to improve the WTG dynamic response and the voltage and current harmonic rejection by using -based controllers. The paper explains how to synthesise three different voltage controllers: the first is a single-loop controller, the second is a cascaded controller and the third is a proportional–resonant controller that is optimised using synthesis. The three -based controllers improve the performance and the robustness obtained with a benchmark case PR controller tuned using the root locus technique. All the controllers are designed in continuous time and implemented in discrete time, applying bilinear discretisation with a sampling rate of 0.25 ms. Detailed PSCAD simulations validate the improvement of the performance and robustness, as well as an improvement in the harmonic rejection. The single controller shows the best combined characteristics of all tried controllers, at the expense of losing the separation between voltage and current control loops.- 19 January 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (2) , 881
Open AccessOperation of DR–HVdc-Connected Grid-Forming Wind Turbine Converters Using Robust Loop-Shaping Controllers
Off-shore wind power plants can be connected to the on-shore grid using diode rectifier HVdc links. As diode rectifiers are passive converters, off-shore WPPs require grid-forming capability. This paper shows how to improve the WTG dynamic response and the voltage and current harmonic rejection by using -based controllers. The paper explains how to synthesise three different voltage controllers: the first is a single-loop controller, the second is a cascaded controller and the third is a proportional–resonant controller that is optimised using synthesis. The three -based controllers improve the performance and the robustness obtained with a benchmark case PR controller tuned using the root locus technique. All the controllers are designed in continuous time and implemented in discrete time, applying bilinear discretisation with a sampling rate of 0.25 ms. Detailed PSCAD simulations validate the improvement of the performance and robustness, as well as an improvement in the harmonic rejection. The single controller shows the best combined characteristics of all tried controllers, at the expense of losing the separation between voltage and current control loops. - Open Access
Identifying the Sweet Spot of Padel Rackets with a Robot
Although the vibration of rackets and the location of the sweet spot for players when hitting the ball is crucial, manufacturers do not specify this behavior precisely. This article analyses padel rackets, provides a solution to determine the sweet spot position (SSP), quantifies its behavior, and determines the level of vibration transmitted along the racket handle. The proposed methods serve to locate the SSP without quantifying it. This article demonstrates the development of equipment capable of analyzing the vibration behavior of padel rackets. To do so, it employs a robot that moves along the surface of the padel racket, striking it along its central line. Accelerometers are placed on a movable cradle where rackets are positioned and adjusted. A method for analyzing accelerometer signals to quantify vibration severity is proposed. The SSP and vibration behavior along the central line are determined and quantified. As a result of the study, 225 padel rackets are analyzed and compared. SSP is independent of the padel racket shape, balance, weight, moment of inertia, and padel racket shape (tear, diamond, or round) and is not located at the same position as the center of percussion.
Open AccessIdentifying the Sweet Spot of Padel Rackets with a Robot
Although the vibration of rackets and the location of the sweet spot for players when hitting the ball is crucial, manufacturers do not specify this behavior precisely. This article analyses padel rackets, provides a solution to determine the sweet spot position (SSP), quantifies its behavior, and determines the level of vibration transmitted along the racket handle. The proposed methods serve to locate the SSP without quantifying it. This article demonstrates the development of equipment capable of analyzing the vibration behavior of padel rackets. To do so, it employs a robot that moves along the surface of the padel racket, striking it along its central line. Accelerometers are placed on a movable cradle where rackets are positioned and adjusted. A method for analyzing accelerometer signals to quantify vibration severity is proposed. The SSP and vibration behavior along the central line are determined and quantified. As a result of the study, 225 padel rackets are analyzed and compared. SSP is independent of the padel racket shape, balance, weight, moment of inertia, and padel racket shape (tear, diamond, or round) and is not located at the same position as the center of percussion.
- Open Access
- 30 November 2023
- Published by MDPI AG in Horticulturae
- Vol. 9 (12) , 1286
Non-Destructive Evaluation of White-Flesh Dragon Fruit Decay with a Robot
Dragon fruit is a tropical fruit with significant potential for consumers and producers. The quality assurance of this high-value product is crucial to satisfy consumer expectations. The quality of imported dragon fruit after storage may deteriorate due to inappropriate storage conditions. The firmness of dragon fruit is an essential parameter to estimate its conditions, and it is usually measured by destructive testing. The objective of the present study is to develop and test a non-destructive robotic sensor for assessing dragon fruit quality related to texture deterioration. Sixty white-fresh dragon fruits obtained from a store were divided in two sets of thirty fruits and stored 48 h at different conditions (cold and room storage) to produce deteriorated and consumer-acceptable fruits. First, the fruit samples were assessed non-destructive with the force sensor of a collaborative robot while they were touched. The robot tool is a pad capable of adapting and copying fruit shapes while controlling its hardness with the jamming transition of its internal granular fill. Second, the fruits were evaluated with destructive tests such as fruit firmness, flesh firmness, and soluble solid content. The procedure followed to produce deteriorated and acceptable fruits were confirmed. A discriminant analysis was carried out to segregate the fruit between the two categories according to the non-destructive variables extracted from the sensor. The variables obtained from the robotic first slope (S1) and the difference between the maximum value and the first overshoot (Os) were significant predictors for the separation in the two quality categories. Promising results were obtained with 77.50% of well classified fruit from the model data set, and 84.21% from the validation data set. The use of the robot could be an efficient tool in evaluating the quality of dragon fruit. This process may lead to substantial savings, particularly considering the elevated cost associated with the importation of tropical fruits into the European market.
- 30 November 2023
- Published by MDPI AG in Horticulturae
- Vol. 9 (12) , 1286
Open AccessNon-Destructive Evaluation of White-Flesh Dragon Fruit Decay with a Robot
Dragon fruit is a tropical fruit with significant potential for consumers and producers. The quality assurance of this high-value product is crucial to satisfy consumer expectations. The quality of imported dragon fruit after storage may deteriorate due to inappropriate storage conditions. The firmness of dragon fruit is an essential parameter to estimate its conditions, and it is usually measured by destructive testing. The objective of the present study is to develop and test a non-destructive robotic sensor for assessing dragon fruit quality related to texture deterioration. Sixty white-fresh dragon fruits obtained from a store were divided in two sets of thirty fruits and stored 48 h at different conditions (cold and room storage) to produce deteriorated and consumer-acceptable fruits. First, the fruit samples were assessed non-destructive with the force sensor of a collaborative robot while they were touched. The robot tool is a pad capable of adapting and copying fruit shapes while controlling its hardness with the jamming transition of its internal granular fill. Second, the fruits were evaluated with destructive tests such as fruit firmness, flesh firmness, and soluble solid content. The procedure followed to produce deteriorated and acceptable fruits were confirmed. A discriminant analysis was carried out to segregate the fruit between the two categories according to the non-destructive variables extracted from the sensor. The variables obtained from the robotic first slope (S1) and the difference between the maximum value and the first overshoot (Os) were significant predictors for the separation in the two quality categories. Promising results were obtained with 77.50% of well classified fruit from the model data set, and 84.21% from the validation data set. The use of the robot could be an efficient tool in evaluating the quality of dragon fruit. This process may lead to substantial savings, particularly considering the elevated cost associated with the importation of tropical fruits into the European market.
- Open Access
- 13 July 2023
- Published by Universitat Politecnica de Valencia
- p. 1-10
Generación de vídeos para TikTok como herramienta de evaluación de prácticas de automática. Primeros resultados
Este artículo presenta los primeros resultados de un proyecto de innovación educativa en la UPV que aplica una metodología de evalaución de practices mediante la generación de vídeos para la red social TikTok. El objetivo principal del proyecto es mejorar la motivación de los alumnos por las prácticas de la asigntura y su evaluación. Para ello se ha diseñado una metodología mediante la cual los alumnos deben generar una serie de vídeos como evidencias de evaluación de las actividades prácticas. Estos vídeos se comparten en TikTok y parte de la calificación se obiente del éxito del vídeo en la red. La actividad resulta motivadora y los alumnos la valoran de manera muy positiva.
- 13 July 2023
- Published by Universitat Politecnica de Valencia
- p. 1-10
Open AccessGeneración de vídeos para TikTok como herramienta de evaluación de prácticas de automática. Primeros resultados
Este artículo presenta los primeros resultados de un proyecto de innovación educativa en la UPV que aplica una metodología de evalaución de practices mediante la generación de vídeos para la red social TikTok. El objetivo principal del proyecto es mejorar la motivación de los alumnos por las prácticas de la asigntura y su evaluación. Para ello se ha diseñado una metodología mediante la cual los alumnos deben generar una serie de vídeos como evidencias de evaluación de las actividades prácticas. Estos vídeos se comparten en TikTok y parte de la calificación se obiente del éxito del vídeo en la red. La actividad resulta motivadora y los alumnos la valoran de manera muy positiva.
- Open Access
- 4 May 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5644
Detection of Bad Stapled Nails in Wooden Packages
Wooden nail-stitched crates are widely used for fruit transportation. Bad stapled nails are transformed into severe product damage that creates stains on the crate due to its juice. In consequence, the final customer depreciates the product because the quality product is in doubt. Human visual inspection of badly stapled nails is a non-effective solution since constant criteria are difficult to reach for all of crate production. A system for the in-line inspection based on a conveyor belt of badly stapled nails in stitched crates is presented. The developed inspection system is discussed with the definition of the computer vision system used to identify fails and the description of image processing algorithms. The experiments are focused on a comparative analysis of the performance of five state-of-the-art classification algorithms based on a deep neural network and traditional computer vision algorithms, highlighting the trade-off between speed and precision in the detection. An accuracy of over 95% is achieved if the user defines the nail location in the image. The presented work constitutes a benchmark to guide deep-learning computer vision algorithms in realistic applications.
- 4 May 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5644
Open AccessDetection of Bad Stapled Nails in Wooden Packages
Wooden nail-stitched crates are widely used for fruit transportation. Bad stapled nails are transformed into severe product damage that creates stains on the crate due to its juice. In consequence, the final customer depreciates the product because the quality product is in doubt. Human visual inspection of badly stapled nails is a non-effective solution since constant criteria are difficult to reach for all of crate production. A system for the in-line inspection based on a conveyor belt of badly stapled nails in stitched crates is presented. The developed inspection system is discussed with the definition of the computer vision system used to identify fails and the description of image processing algorithms. The experiments are focused on a comparative analysis of the performance of five state-of-the-art classification algorithms based on a deep neural network and traditional computer vision algorithms, highlighting the trade-off between speed and precision in the detection. An accuracy of over 95% is achieved if the user defines the nail location in the image. The presented work constitutes a benchmark to guide deep-learning computer vision algorithms in realistic applications.
- Open Access
Identifying the Inertial Properties of a Padel Racket: An Experimental Maneuverability Proposal
Although the moment of inertia of padel rackets is one of their fundamental properties and of particular interest to the players, hardly any manufacturer specifies the parameter for its rackets. The present paper offers a solution to determine the moment of inertia around different axes of padel rackets and makes a standardized comparison possible. After a short overview of the physical background of the problem and the existing solutions for inertia testing, the developed concept for a test stand is described in detail. The approach uses the fact that a pendulum swings with its natural frequency, which depends directly on its moment of inertia. The inertia can be calculated by measuring the cycle time of the swing. Two different test stands, a trifilar and a swing pendulum, are designed to enable an oscillation of the rackets with different rotation axes, and an acceleration sensor is used to measure its natural frequency. A user-friendly interface acquires and processes accelerometer data providing inertial moments. A calibration model defines sensor accuracy. Precision is estimated by calculating the influence of the measurement errors and by testing the repeatability. The maneuverability parameter is created, and in the last step, various rackets are evaluated to create a database with the main properties. As a result of the study of the racket population, a maneuverability parameter is proposed to classify the rackets in a comprehensible way for users. The classification method is tested with users to explore the matching between the scientific classification and the player’s feelings. The results are shown and explained.
Open AccessIdentifying the Inertial Properties of a Padel Racket: An Experimental Maneuverability Proposal
Although the moment of inertia of padel rackets is one of their fundamental properties and of particular interest to the players, hardly any manufacturer specifies the parameter for its rackets. The present paper offers a solution to determine the moment of inertia around different axes of padel rackets and makes a standardized comparison possible. After a short overview of the physical background of the problem and the existing solutions for inertia testing, the developed concept for a test stand is described in detail. The approach uses the fact that a pendulum swings with its natural frequency, which depends directly on its moment of inertia. The inertia can be calculated by measuring the cycle time of the swing. Two different test stands, a trifilar and a swing pendulum, are designed to enable an oscillation of the rackets with different rotation axes, and an acceleration sensor is used to measure its natural frequency. A user-friendly interface acquires and processes accelerometer data providing inertial moments. A calibration model defines sensor accuracy. Precision is estimated by calculating the influence of the measurement errors and by testing the repeatability. The maneuverability parameter is created, and in the last step, various rackets are evaluated to create a database with the main properties. As a result of the study of the racket population, a maneuverability parameter is proposed to classify the rackets in a comprehensible way for users. The classification method is tested with users to explore the matching between the scientific classification and the player’s feelings. The results are shown and explained.
- Open Access
- 31 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1557
Improving Robot Perception Skills Using a Fast Image-Labelling Method with Minimal Human Intervention
Robot perception skills contribute to natural interfaces that enhance human–robot interactions. This can be notably improved by using convolutional neural networks. To train a convolutional neural network, the labelling process is the crucial first stage, in which image objects are marked with rectangles or masks. There are many image-labelling tools, but all require human interaction to achieve good results. Manual image labelling with rectangles or masks is labor-intensive and unappealing work, which can take months to complete, making the labelling task tedious and lengthy. This paper proposes a fast method to create labelled images with minimal human intervention, which is tested with a robot perception task. Images of objects taken with specific backgrounds are quickly and accurately labelled with rectangles or masks. In a second step, detected objects can be synthesized with different backgrounds to improve the training capabilities of the image set. Experimental results show the effectiveness of this method with an example of human–robot interaction using hand fingers. This labelling method generates a database to train convolutional networks to detect hand fingers easily with minimal labelling work. This labelling method can be applied to new image sets or used to add new samples to existing labelled image sets of any application. This proposed method improves the labelling process noticeably and reduces the time required to start the training process of a convolutional neural network model.
- 31 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1557
Open AccessImproving Robot Perception Skills Using a Fast Image-Labelling Method with Minimal Human Intervention
Robot perception skills contribute to natural interfaces that enhance human–robot interactions. This can be notably improved by using convolutional neural networks. To train a convolutional neural network, the labelling process is the crucial first stage, in which image objects are marked with rectangles or masks. There are many image-labelling tools, but all require human interaction to achieve good results. Manual image labelling with rectangles or masks is labor-intensive and unappealing work, which can take months to complete, making the labelling task tedious and lengthy. This paper proposes a fast method to create labelled images with minimal human intervention, which is tested with a robot perception task. Images of objects taken with specific backgrounds are quickly and accurately labelled with rectangles or masks. In a second step, detected objects can be synthesized with different backgrounds to improve the training capabilities of the image set. Experimental results show the effectiveness of this method with an example of human–robot interaction using hand fingers. This labelling method generates a database to train convolutional networks to detect hand fingers easily with minimal labelling work. This labelling method can be applied to new image sets or used to add new samples to existing labelled image sets of any application. This proposed method improves the labelling process noticeably and reduces the time required to start the training process of a convolutional neural network model.
- 1 April 2019
- Published by Elsevier in Biosystems Engineering
- Vol. 180, 161-167
An ultra-low pressure pneumatic jamming impact device to non-destructively assess cherimoya firmness
- 1 April 2019
- Published by Elsevier in Biosystems Engineering
- Vol. 180, 161-167
An ultra-low pressure pneumatic jamming impact device to non-destructively assess cherimoya firmness