RDRavikumar Dumpala

Ravikumar Dumpala

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ravikumar Dumpala has a total of 158 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Developing Nanostructured Calcium-Based Bio-Ceramic Materials From Natural Source

    by Ratna Sunil Buradagunta, Ravikumar Dumpala

    Synthesizing calcium based ceramic materials from natural source such as fish bones, sea corals and egg shells is cost effective route to produce nanocrystalline bio-ceramic materials. These nano-ceramic phases contain special ions which help to induce additional benefits when used as biomaterials. Since, the size of the produced phases is in nano-level, applications including local drug delivery, surface coatings on implants and producing nano-composites can be benefited due to the promising properties of nano-crystalline materials. The present chapter provides a comprehensive summary of the developments in synthesizing nano-crystalline calcium based ceramic materials from the natural sources for biomaterial applications. The characterization, performance evaluation, and potential applications of using these nano-phases in biomedical applications are discussed in detail. Furthermore, future perspectives and the potential applications in medical fields are briefly presented.

  • Enhancing surface wear resistance of aluminum and magnesium alloys through friction stir processed surface composites: a critical review

    by Hemendra Patle, Ratna Sunil Buradagunta, Ravikumar Dumpala

    Purpose: The purpose of present review is to provide a critical summary on producing surface composites of Al and Mg composites by friction stir processing (FSP). More focus is given on surface hardness and wear properties of the composites produced by FSP. Design/methodology/approach: The approach to present the review on developing surface composites by friction stir processing (FSP) includes a detailed introduction to FSP and the role of process parameters on successfully producing the Al and Mg based composites followed by presenting surface hardness and wear characteristics of these composites. Findings: The reported literature summary concludes using FSP as surface engineering method to enhance wear resistance of Al and Mg components as a promising strategy. Originality/value: The presented review helps the researchers to refer a critical summary on developing surface composites of Al and Mg by FSP specifically to attain a comprehensive understanding of wear properties of these surface composites. Peer review: The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2025-0194/


  • Open Access

    Effect of Burnishing Load on Surface Roughness and Wear Behaviour of ZE41 Magnesium Alloy

    by S.K. Baral, M.M. Thawre, B.R. Sunil, Ravikumar Dumpala

    Magnesium (Mg) alloys have become an attractive choice for lightweight structural applications. However, improving the tribological characteristics of Mg alloys is essential to widen the range of applications. In the present work, ball burnishing was performed with different burnishing loads from 40 N to 80 N to investigate its effect on surface roughness, microhardness, and wear resistance. It was found that the 50 N burnishing load exhibits the best surface finish with a reduction of 46.2% in surface roughness compared to unburnished alloy. The highest microhardness was observed at 60 N load with an improvement of ~35.5%. Higher loads beyond 50 N resulted in increased surface roughness. Higher burnishing load caused surface distortion and flaking which decreased the microhardness beyond 60 N load. At 50 N burnishing load, better wear resistance with a reduction of ~40% was achieved compared to unburnished alloy. Improvement in surface finish and microhardness are responsible for better wear resistance. Worn surfaces exhibited abrasion, oxidation, and delamination wear mechanisms in the unburnished sample. Whereas, delamination wear was absent in the burnished specimen at 50 N burnishing load.


  • Open Access

    Characterization, Mechanical and Corrosion Behavior of Mg-Sn-Pb Alloy Produced by Friction Surface Alloying

    by Ratna Sunil Buradagunta, B. Venkateswarlu, Ambuj Sharma, Feroz Shaik, Ravikumar Dumpala

    The current paper demonstrates friction-assisted surface alloying to produce Mg-Sn-Pb alloy within the solid state by using friction stir processing (FSP) principle. A groove is machined on the surface of pure magnesium sheet and a thin wire of Sn-Pb was inserted into the groove and then FSP was carried out on the surface. In order to achieve uniformity in the alloy formation, second pass was also carried out on the stirred region. Development of Mg-Sn-Pb alloy was observed at the surface as reflected from the corresponding X-ray diffraction peaks. Surface micro-hardness of the produced surface Mg-Sn-Pb alloy was significantly increased than pure Mg. Corrosion behavior was assessed by polarization tests and the result indicated higher corrosion resistance for the produced alloy due to the developed solid solution grains. Both the first-pass and second-pass samples have exhibited similar levels of corrosion resistance. Higher tensile strength (148.7 ± 5.1 MPa) was observed for the produced surface alloy and second-pass marginally elevated the tensile strength (152.1 ± 3.8 MPa) compared with Mg (106.2 ± 4.2 MPa). Higher ductility was also observed as reflected from the increased % of elongation (7.4 ± 0.8 and 8.2 ± 1.1) for the produced alloys compared with Mg (4.3 ± 0.7). The present work demonstrates the potential of friction surface alloying to develop Mg-Sn-Pb alloy without melting the base material that exhibits improved corrosion and tensile properties. Furthermore, it is also concluded that the second pass marginally increases the corrosion and mechanical performance of the alloy.

  • Producing Al-Zn Alloy Coating on the Pure Al Substrate by Solid-State Friction Surfa ce Alloying

    by Ratna Sunil Buradagunta, Ambuj Sharma, Tapan K. Mahanta, Shaik Feroz, Ravikumar Dumpala

    Using friction-assisted solid-state processes in the surface engineering of metals and alloys addresses the challenges involved in liquid-state methods. In the present work, friction surface alloying (FSA) was used to deposit Al-Zn alloy coating as a layer on pure Al substrate. Zn powder was filled in the holes produced longitudinally in a pure Al rod and was used as the consumable rod. Processing was done at 1100 rpm with 25 mm/min feed rate at a worktable vertical feed of 5 mm/min. Due to the generated heat during the friction surfacing, the zinc reinforcement was melted and a solid solution alloy of Al-Zn was produced on pure Al. The cross-sectional microstructure clearly indicated a strong metallurgical bonding at the alloy-substrate interface. Phase analysis carried out by X-ray diffraction studies confirms the developed Al-Zn alloy in the coated surface. Hardness measurements at the cross-section and at the surface demonstrated improvement (75.2±8.3 HV0.1) compared with the substrate (36.5±7.1 HV0.1) due to the formation of the alloy. Corrosion experiments by polarization studies revealed significant improvement in the corrosion resistance for the produced surface alloy as reflected from the lower corrosion current density (1.39×10–4 A/cm2) compared with the substrate (1.83×10–3 A/cm2). Higher tensile strength (245.5±5.2 MPa) was measured for the developed alloy than the substrate (182.1±6.9 MPa) without losing the ductility significantly. The results demonstrate the potential of FSA to develop surface alloys within the solid-state itself.

  • Open Access

    Effect of Ram Speed on the Integrity of AA6063 Extruded Profile through Porthole Die

    by V.N.S.U. Viswanat H Ammu, P.M. Padole, A. Agnihotri, Ravikumar Dumpala

    In aluminium extrusion, porthole dies are extensively used for hollow profiles production. In this work, a porthole die with three portholes around the die centre was used to produce Aluminium Magnesium Silicon based AA6063 alloy profile. Press trials were conducted using horizontal type extrusion press of capacity 690 Ton under different ram speeds i.e. 2, 4.5 and 6 mm/s for producing profiles. Subsequently, the profiles produced were aged at 175°C for 6 hours and microstructures were observed. Further, samples drawn from extruded profiles were tested for tensile properties and hardness. X-ray diffraction (XRD) analysis was carried out for identification of phases. Further, the profiles produced were evaluated for weld strength integrity using wedge expansion test. Results indicated that grain refinement has occurred while extruding the samples from billet with initial grain size of 67 μm to profiles. Also, compression load in wedge expansion test was recorded for profiles produced at a ram speed of 2 mm/s with 22.74 ± 0.92 kN with decreasing trend of compression load for profiles extruded at 4.5 mm/s and 6 mm/s, which indicated that lower ram speed produces profiles with high weld strength integrity.

  • Effect of T5 ageing on tensile characteristics and longitudinal weld quality of Al–Mg–Si alloy extrudates

    by V.N.S.U. Viswanath Ammu, Pramod M. Padole, Anupam Agnihotri, Ravikumar Dumpala

  • Wear Characteristics of Thermally Sprayed Diamond-Reinforced Ni-P Coatings

    by Akshay R. Govande, Subrat Kumar Baral, Ravikumar Dumpala, Shrikant Joshi