H. R. Strauss
Research Subjects
H. R. Strauss has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
Jet Contributors
3 shared publications- Amnon Fruchtman
H.I.T. - Holon Institute of Technology , 52 Golomb St., Holon 58102
2 shared publications B. C. Lyons
2 shared publicationsB. E. Chapman
Dept. of Physics University of Wisconsin 53706 Madison WI USA
2 shared publicationsB. Rubinstein
Faculty of Physics, Weizmann Institute of Science 1 , Rehovot 76100, Israel
2 shared publications- Brendan C. Lyons
General Atomics, San Diego, CA 92121, United States of America
2 shared publications
Latest Publications
- Top Cited PapersOpen Access
- 4 September 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (10) , 103001
MHD, disruptions and control physics: Chapter 4 of the special issue: on the path to tokamak burning plasma operation
In this chapter, we review the progress in MHD stability, disruptions and control in magnetic fusion research that has occurred over the past (more than) one and a half decades since the publication by Hender et al in 2007 on the same topic as part of the update of ITER Physics Basis. During this period, remarkable progress has been achieved in the understanding of the basic physics and overall control of MHD instabilities through a wide spectrum of dedicated experiments, theory and modeling. The sawtooth activities are probably today one of the best understood of MHD events and very robust control schemes have been developed for reliable operation of tokamaks through core heating. Similarly, significant improvements have been achieved in understanding and control of neoclassical tearing modes, resistive wall modes or locked modes and their control through ECCD or error field control. The field of disruption prediction through application of artificial intelligence, machine learning or deep learning methods, which had already started at the time of the 2007 review, has progressed significantly due to general progress in these fields and application of newer, more sophisticated algorithms. However, although remarkable progress has been achieved in the field of Disruptions, their understanding, prediction, possible avoidance and mitigation still remain probably the most active fields of R&D globally in this field. This is especially because reactor grade machines like ITER and DEMO will be much less tolerant in respect of disruptions and runaway currents, and their occurrences must be either avoided altogether or minimized to an acceptable value without causing any significant hindrance to robust machine operations. This review is intended to present a broad spectrum of the R&D that has occurred in this field in support of ITER, which will also be of immense significance for all future machines, especially reactors like DEMO.
- 4 September 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (10) , 103001
Top Cited PapersOpen AccessMHD, disruptions and control physics: Chapter 4 of the special issue: on the path to tokamak burning plasma operation
In this chapter, we review the progress in MHD stability, disruptions and control in magnetic fusion research that has occurred over the past (more than) one and a half decades since the publication by Hender et al in 2007 on the same topic as part of the update of ITER Physics Basis. During this period, remarkable progress has been achieved in the understanding of the basic physics and overall control of MHD instabilities through a wide spectrum of dedicated experiments, theory and modeling. The sawtooth activities are probably today one of the best understood of MHD events and very robust control schemes have been developed for reliable operation of tokamaks through core heating. Similarly, significant improvements have been achieved in understanding and control of neoclassical tearing modes, resistive wall modes or locked modes and their control through ECCD or error field control. The field of disruption prediction through application of artificial intelligence, machine learning or deep learning methods, which had already started at the time of the 2007 review, has progressed significantly due to general progress in these fields and application of newer, more sophisticated algorithms. However, although remarkable progress has been achieved in the field of Disruptions, their understanding, prediction, possible avoidance and mitigation still remain probably the most active fields of R&D globally in this field. This is especially because reactor grade machines like ITER and DEMO will be much less tolerant in respect of disruptions and runaway currents, and their occurrences must be either avoided altogether or minimized to an acceptable value without causing any significant hindrance to robust machine operations. This review is intended to present a broad spectrum of the R&D that has occurred in this field in support of ITER, which will also be of immense significance for all future machines, especially reactors like DEMO.
- Open Access
- 1 March 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (3)
Prevention of resistive wall tearing mode major disruptions with feedback
Resistive wall tearing modes (RWTMs) can cause major disruptions. A signature of RWTMs is that the rational surface is sufficiently close to the wall to interact with it. For (m,n)=(2,1) modes, a RWTM requires normalized minor radius of the rational surface ρq2≥0.75, which can also be expressed as q75≤2. Major disruptions can occur when the criterion is satisfied. This is confirmed in simulations and theory and in a DIII-D locked mode disruption database. The q75<2 criterion is valid at high β as well as at low β. A very important feature of RWTMs is that they can be feedback stabilized. If the ρq2 criterion is not satisfied, or if the wall is ideally conducting, then the mode does not produce a major disruption, although it can produce a minor disruption. Feedback, or rotation of the mode at the wall by complex feedback, can emulate an ideal wall, preventing major disruptions. The ρq2 criterion depends weakly on the wall radius. A simple geometric model of its dependence on wall radius is given.
- 1 March 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (3)
Open AccessPrevention of resistive wall tearing mode major disruptions with feedback
Resistive wall tearing modes (RWTMs) can cause major disruptions. A signature of RWTMs is that the rational surface is sufficiently close to the wall to interact with it. For (m,n)=(2,1) modes, a RWTM requires normalized minor radius of the rational surface ρq2≥0.75, which can also be expressed as q75≤2. Major disruptions can occur when the criterion is satisfied. This is confirmed in simulations and theory and in a DIII-D locked mode disruption database. The q75<2 criterion is valid at high β as well as at low β. A very important feature of RWTMs is that they can be feedback stabilized. If the ρq2 criterion is not satisfied, or if the wall is ideally conducting, then the mode does not produce a major disruption, although it can produce a minor disruption. Feedback, or rotation of the mode at the wall by complex feedback, can emulate an ideal wall, preventing major disruptions. The ρq2 criterion depends weakly on the wall radius. A simple geometric model of its dependence on wall radius is given.
- Open Access
- 3 September 2024
- Published by IOP Publishing in Nuclear Fusion
- Vol. 64 (10) , 106037
Resistive wall tearing mode disruptions
This paper deals with resistive wall tearing mode (RWTM) disruptions. RWTMs are closely related to resistive wall modes. RWTMs are tearing modes whose linear and nonlinear behavior is strongly dependent on the resistive wall outside the plasma. The consequence for ITER, is that the thermal quench timescale could be much longer than previously conjectured. Active feedback stabilization is another possible way to mitigate or prevent RWTM disruptions. Simulations of RWTM disruptions are reviewed for DIII-D and MST. MST has a longer resistive wall time than ITER, and disruptions are not observed experimentally when MST is operated as a standard tokamak. Simulations indicate that the RWTM disruption time scale is longer than the experimental shot time. Edge cooling causes contraction of the current profile, which can destabilize RWTMs. The equilibria studied here have the q = 2 rational surface close to the edge of the plasma, and low current density between the q = 2 surface and the wall. A sequence of low edge current model equilibria has major disruptions only for a resistive, not ideal, wall, and edge q ⩽ 3.4 . This is consistent with regimes of tokamak disruptivity, suggesting that tokamak disruptions caused by edge cooling at low edge q could be RWTMs.
- 3 September 2024
- Published by IOP Publishing in Nuclear Fusion
- Vol. 64 (10) , 106037
Open AccessResistive wall tearing mode disruptions
This paper deals with resistive wall tearing mode (RWTM) disruptions. RWTMs are closely related to resistive wall modes. RWTMs are tearing modes whose linear and nonlinear behavior is strongly dependent on the resistive wall outside the plasma. The consequence for ITER, is that the thermal quench timescale could be much longer than previously conjectured. Active feedback stabilization is another possible way to mitigate or prevent RWTM disruptions. Simulations of RWTM disruptions are reviewed for DIII-D and MST. MST has a longer resistive wall time than ITER, and disruptions are not observed experimentally when MST is operated as a standard tokamak. Simulations indicate that the RWTM disruption time scale is longer than the experimental shot time. Edge cooling causes contraction of the current profile, which can destabilize RWTMs. The equilibria studied here have the q = 2 rational surface close to the edge of the plasma, and low current density between the q = 2 surface and the wall. A sequence of low edge current model equilibria has major disruptions only for a resistive, not ideal, wall, and edge q ⩽ 3.4 . This is consistent with regimes of tokamak disruptivity, suggesting that tokamak disruptions caused by edge cooling at low edge q could be RWTMs.
- Open Access
Resistive Wall Tearing Mode Disruptions
This paper deals with resistive wall tearing mode (RWTM) disruptions. RWTMs are closely related to resistive wall modes (RWMs). The nonlinear behavior of these modes is strongly dependent on the resistive wall outside the plasma. A conducting wall is highly mitigating for RWTM disruptions. The consequence for ITER, which has a highly conducting wall, is that the thermal quench (TQ) time could be much longer than previously conjectured. Active feedback stabilization is another possible way to mitigate or prevent RWTM disruptions. Simulations of disruptions are reviewed for DIII-D and MST. MST has a longer resistive wall time than ITER, and disruptions are not observed experimentally when MST is operated as a standard tokamak. Simulations indicate that the RWTM disruption time scale is longer than the experimental shot time. In general, edge cooling by tearing mode island overlap or by impurity radiation causes contraction of the current profile, which destabilizes RWTMs. The equilibria studied here have a q = 2 rational surface close to the edge of the plasma, and low edge current density. A sequence of low edge current model equilibria hasmajor disruptions only for a resistive, not ideal, wall, and approximately edge q < 3. This is consistent with typical regimes of tokamak disruption avoidance, suggesting that typical tokamak disruptions could be RWTMs.
Open AccessResistive Wall Tearing Mode Disruptions
This paper deals with resistive wall tearing mode (RWTM) disruptions. RWTMs are closely related to resistive wall modes (RWMs). The nonlinear behavior of these modes is strongly dependent on the resistive wall outside the plasma. A conducting wall is highly mitigating for RWTM disruptions. The consequence for ITER, which has a highly conducting wall, is that the thermal quench (TQ) time could be much longer than previously conjectured. Active feedback stabilization is another possible way to mitigate or prevent RWTM disruptions. Simulations of disruptions are reviewed for DIII-D and MST. MST has a longer resistive wall time than ITER, and disruptions are not observed experimentally when MST is operated as a standard tokamak. Simulations indicate that the RWTM disruption time scale is longer than the experimental shot time. In general, edge cooling by tearing mode island overlap or by impurity radiation causes contraction of the current profile, which destabilizes RWTMs. The equilibria studied here have a q = 2 rational surface close to the edge of the plasma, and low edge current density. A sequence of low edge current model equilibria hasmajor disruptions only for a resistive, not ideal, wall, and approximately edge q < 3. This is consistent with typical regimes of tokamak disruption avoidance, suggesting that typical tokamak disruptions could be RWTMs.
- Open Access
- 1 November 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (11)
Models of resistive wall tearing mode disruptions
Disruptions are a serious issue in tokamaks. In a disruption, the thermal energy is lost by means of an instability which could be a resistive wall tearing mode (RWTM). During precursors to a disruption, the plasma edge region cools, causing the current to contract. Model sequences of contracted current equilibria are given, and their stability is calculated. A linear stability study shows that there is a maximum value of edge qa≈3 for RWTMs to occur. This also implies a minimum rational surface radius normalized to plasma radius from RWTMs to be unstable. Nonlinear simulations are performed using a similar model sequence derived from an equilibrium reconstruction. There is a striking difference in the results, depending on whether the wall is ideal or resistive. With an ideal wall, the perturbations saturate at moderate amplitude, causing a minor disruption without a thermal quench. With a resistive wall, there is a major disruption with a thermal quench, if the edge qa≤3. There is a sharp transition in nonlinear behavior at qa=3. This is consistent with the linear model and with experiments. If disruptions are caused by RWTMs, then devices with highly conducting walls, such as the International Tokamak Experimental Reactor will experience much milder, tolerable, disruptions than presently predicted.
- 1 November 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (11)
Open AccessModels of resistive wall tearing mode disruptions
Disruptions are a serious issue in tokamaks. In a disruption, the thermal energy is lost by means of an instability which could be a resistive wall tearing mode (RWTM). During precursors to a disruption, the plasma edge region cools, causing the current to contract. Model sequences of contracted current equilibria are given, and their stability is calculated. A linear stability study shows that there is a maximum value of edge qa≈3 for RWTMs to occur. This also implies a minimum rational surface radius normalized to plasma radius from RWTMs to be unstable. Nonlinear simulations are performed using a similar model sequence derived from an equilibrium reconstruction. There is a striking difference in the results, depending on whether the wall is ideal or resistive. With an ideal wall, the perturbations saturate at moderate amplitude, causing a minor disruption without a thermal quench. With a resistive wall, there is a major disruption with a thermal quench, if the edge qa≤3. There is a sharp transition in nonlinear behavior at qa=3. This is consistent with the linear model and with experiments. If disruptions are caused by RWTMs, then devices with highly conducting walls, such as the International Tokamak Experimental Reactor will experience much milder, tolerable, disruptions than presently predicted.
- 29 June 2023
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 65 (8) , 084002
MST resistive wall tearing mode simulations
The Madison Symmetric Torus (MST) is a toroidal device that, when operated as a standard tokamak, does not have major disruptions. Unlike most tokamaks, the MST plasma is surrounded by a close fitting highly conducting wall, with a resistive wall penetration time two orders of magnitude longer than in JET or DIII-D, and three times longer than in ITER. The MST can operate with edge q a ⩽ 2 , unlike standard tokamaks. Simulations presented here indicate that the MST is unstable to resistive wall tearing modes (RWTMs) and resistive wall modes (RWMs). They could in principle cause disruptions, but the predicted thermal quench (TQ) time is much longer than the experimental pulse time. If the MST TQ time were comparable to measurements in JET and DIII-D, theory and simulations predict that disruptions would have been observed in MST. This is consistent with the modeling herein, predicting that disruptions are caused by RWTMs and RWMs. In the low q a ∼ 2 regime of MST, the RWTM asymptotically satisfies the RWM dispersion relation. The transition from RWTM to RWM occurs smoothly at q a = m / n , where m , n are poloidal and toroidal mode numbers.
- 29 June 2023
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 65 (8) , 084002
MST resistive wall tearing mode simulations
The Madison Symmetric Torus (MST) is a toroidal device that, when operated as a standard tokamak, does not have major disruptions. Unlike most tokamaks, the MST plasma is surrounded by a close fitting highly conducting wall, with a resistive wall penetration time two orders of magnitude longer than in JET or DIII-D, and three times longer than in ITER. The MST can operate with edge q a ⩽ 2 , unlike standard tokamaks. Simulations presented here indicate that the MST is unstable to resistive wall tearing modes (RWTMs) and resistive wall modes (RWMs). They could in principle cause disruptions, but the predicted thermal quench (TQ) time is much longer than the experimental pulse time. If the MST TQ time were comparable to measurements in JET and DIII-D, theory and simulations predict that disruptions would have been observed in MST. This is consistent with the modeling herein, predicting that disruptions are caused by RWTMs and RWMs. In the low q a ∼ 2 regime of MST, the RWTM asymptotically satisfies the RWM dispersion relation. The transition from RWTM to RWM occurs smoothly at q a = m / n , where m , n are poloidal and toroidal mode numbers.
- Open Access
A Model of Tokamak Locked Mode Disruptions
Locked modes are precursors to major disruptions. During locked modes, the temperature decreases in the plasma edge region. This causes the current to contract. A model is given to analyze the MHD stability of contracted current equilibria. If there is sufficient current contraction, resistive wall tearing modes are destabilized. This requires that the q = 2 surface be sufficiently close to the wall. The threshold conditions obtained in the model are consistent with experimental observations of the conditions for a thermal quench in a disruption.
Open AccessA Model of Tokamak Locked Mode Disruptions
Locked modes are precursors to major disruptions. During locked modes, the temperature decreases in the plasma edge region. This causes the current to contract. A model is given to analyze the MHD stability of contracted current equilibria. If there is sufficient current contraction, resistive wall tearing modes are destabilized. This requires that the q = 2 surface be sufficiently close to the wall. The threshold conditions obtained in the model are consistent with experimental observations of the conditions for a thermal quench in a disruption.
- Open Access
MST Resistive Wall Tearing Mode Simulations
The Madison Symmetric Torus (MST) is a toroidal device that, when operated as a tokamak, is resistant to disruptions. Unlike most tokamaks, the MST plasma is surrounded by a close fitting highly conducting wall, with a resistive wall penetration time two orders of magnitude longer than in JET or DIII-D, and three times longer than in ITER. The MST can operate with edge q_a < 2, unlike standard tokamaks. Simulations presented here indicate that the MST is unstable to resistive wall tearing modes (RWTMs) and resistive wall modes (RWMs). They could in principle cause disruptions, but the predicted thermal quench time is much longer than the experimental pulse time. If the MST thermal quench time were comparable to measurements in JET and DIII-D, theory and simulations predict that disruptions would have been observed in MST. This is consistent with the modeling herein, predicting that disruptions are caused by RWTMs and RWMs. In the low q_a regime of MST, the RWTM asymptotically satisfies the RWM dispersion relation. The transition from RWTM to RWM occurs smoothly at q_a = m/n, where m,n are poloidal and toroidal mode numbers.
Open AccessMST Resistive Wall Tearing Mode Simulations
The Madison Symmetric Torus (MST) is a toroidal device that, when operated as a tokamak, is resistant to disruptions. Unlike most tokamaks, the MST plasma is surrounded by a close fitting highly conducting wall, with a resistive wall penetration time two orders of magnitude longer than in JET or DIII-D, and three times longer than in ITER. The MST can operate with edge q_a < 2, unlike standard tokamaks. Simulations presented here indicate that the MST is unstable to resistive wall tearing modes (RWTMs) and resistive wall modes (RWMs). They could in principle cause disruptions, but the predicted thermal quench time is much longer than the experimental pulse time. If the MST thermal quench time were comparable to measurements in JET and DIII-D, theory and simulations predict that disruptions would have been observed in MST. This is consistent with the modeling herein, predicting that disruptions are caused by RWTMs and RWMs. In the low q_a regime of MST, the RWTM asymptotically satisfies the RWM dispersion relation. The transition from RWTM to RWM occurs smoothly at q_a = m/n, where m,n are poloidal and toroidal mode numbers.
- Open Access
- 1 November 2022
- Published by AIP Publishing in Physics of Plasmas
- Vol. 29 (11)
Resistive wall tearing mode disruptions in DIII-D and ITER tokamaks
Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTMs) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. The nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.
- 1 November 2022
- Published by AIP Publishing in Physics of Plasmas
- Vol. 29 (11)
Open AccessResistive wall tearing mode disruptions in DIII-D and ITER tokamaks
Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTMs) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. The nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.
- Open Access
Locked mode disruptions in DIII-D and application to ITER
Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTM) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall, and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. The nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.
Open AccessLocked mode disruptions in DIII-D and application to ITER
Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTM) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall, and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. The nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.