PTParth S. Thakar

Parth S. Thakar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Parth S. Thakar has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Discrete sliding mode control for single board heater system with implementation using open source tools

    by Parth S Thakar, Anilkumar Markana, Piyush B Miyani

    In this paper, a new application of discrete sliding mode control (DSMC) is reported for a single board heater system (SBHS). The system model is identified using least-square optimization. A non-switching type stable DSMC is developed for an uncertain system. For this, exact and non-conservative stability boundaries are also identified. Additionally, a high-gain observer (HGO) strategy is embedded together through the zero-order hold (ZOH) based implementation scheme, for its realization with the controller. This study compares the set-point tracking performance of DSMC, tuned PID and pole placement control strategies in SBHS simulations, resulting DSMC to achieve the lowest ITAE and ITSE errors. Normally in the simulation the modeling errors and uncertainties especially for systems like SBHS, are not considered. They become prominent in the practical scenario where thermal inertia, delay in the output response, sampling errors, nonlinearities, drift in the system parameters play a significant role and hence the performance of the controller needs to be evaluated for practical implementation. The effectiveness of the suggested controller-observer scheme is experimentally validated on a real SBHS setup through the open source software tools like Scilab and Xcos. Moreover, the experimental results are demonstrated alongside their respective analysis. Some important observations and conclusions from the overall study are deduced.

  • Cascade-trained deep reinforcement learning for PID gain optimization in precise joint position control of 6-DoF robotic arm

    by Dhaval R Vyas, Parth S Thakar, Anilkumar Markana, Nitin Padhiyar

    The problem of precise joint position tracking has remained as a core challenge for a 6-DoF Cobot arm, especially due to often scenario of an arbitrary waypoint reference trajectory generated due to human interactions. To tackle this problem, we propose a novel cascade training based Deep Reinforcement Learning (DRL) algorithm that tunes the PID controller gains for each joint simultaneously, ensuring accurate positional tracking for all joints. This also addresses the problem of overestimation of control parameters by ensuring that performance criteria are met in a phased manner during the training process. The tuned DRL based PID clearly outperforms the conventional PID control by accurately tracking the arbitrary waypoints given to each joints of the Cobot arm. We show the efficacy of the proposed method through exhaustive simulations and performing quantitative analysis of various key performance criteria like- Mean Absolute Error (MAE), Root Mean Square Error (RMSE), and Average Control Effort (ACE) error for the Cobot. The obtained results of DRL-PID control, when compared with its conventional PID counterpart, clearly depict the superiority of the proposed DRL-PID scheme via a cascade training approach. We have also remarked on some trade off and implementation aspects of the proposed control policy for the Cobot based applications. This method has the potential to be applicable to similar complex dynamical systems like a Cobot, where arbitrary reference and human interactions are prime concerns.


  • Novel custom-made design and analysis of hydrogen PEM fuel cell for high endurance small UAV applications

    by Soham Prajapati, Parth S. Thakar, Anilkumar Markana

    The purpose of this paper is to propose a new methodology to devise a custom-made hydrogen-based proton-exchange membrane fuel cell (PEMFC) system for a class of experimental fixed-wing small unmanned aerial vehicles (SUAVs). The proposed fuel cell provides three times higher flight endurance than the conventional battery-based powertrain. The chosen SUAV represents a class of high-altitude UAVs, having an operational altitude of 4500 m (14,760ft), cruising speed of 12–20 m/s (39.4–65.6 ft/s), take-off weight of 4 kg, wing-span of 1.61 m (5.28 ft) and battery-powered flight endurance of 1 h. The characteristic parameters and design configurations of the fuel cell are determined by employing the first principles of electrochemistry and thermodynamics. Corresponding simulations are performed using popular development tools like MATLAB/Simulink. The vital results in the form of - polarization and power curves for fuel cells, against the current density are obtained, which are further narrowed down to meet the target power requirements for determining the size of the hydrogen storage tank. The paper also comments on the auxiliary systems and fuel cell powertrain for SUAVs. Finally, the design efficiency of 54% for the fuel cell is achieved with respect to equivalent voltage for heating value with the calculated hydrogen storage tank size of 5.688 ls. This yields three times higher flight endurance as compared to the flight time found in literature for the same class of SUAVs.


  • Open Access

    Novel custom-made design and analysis of hydrogen PEM fuel cell for high endurance small UAV applications

    by Soham Prajapati, Parth S. Thakar, Anilkumar Markana

    The purpose of this paper is to propose a new methodology to devise a custom-made hydrogen-based proton exchange membrane fuel cell (\textcolor{red}{PEMFC}) system for a class of experimental fixed-wing small unmanned aerial vehicles (SUAVs). The proposed fuel cell provides three times higher flight endurance than the conventional battery-based powertrain. The chosen SUAV \textcolor{red}{represents} a class of high-altitude UAVs, having an operational altitude of 4500m \textcolor{red}{(14,760ft)}, cruising speed of 12-20 m/s (39.4 - 65.6 ft/s), take-off weight of 4 kg, wing-span of 1.61 m (5.28 ft) and battery-powered flight endurance of one hour. The characteristic parameters and design configurations of the fuel cell are determined by employing \textcolor{red}{the first} principles of electrochemistry and thermodynamics. Corresponding simulations are performed \textcolor{red}{using} popular development tools like MATLAB/Simulink. The vital results in the form of – polarization and power curves for fuel cell, against the current density are obtained, which are further narrowed down to meet the target power requirements for determining the size of the hydrogen storage tank. The paper also comments on the auxiliary systems and fuel cell powertrain for SUAVs. \textcolor{red}{Finally, the design efficiency of 54% for the fuel cell is achieved with respect to equivalent voltage for heating value with the calculated hydrogen storage tank size of 5.688 litres. This yields three times higher flight endurance as compared to the flight time found in literature for the same class of SUAVs. }

  • Open Access

    Improved output‐feedback second order sliding mode control design with implementation for underactuated slosh‐container system having confined track length

    by Parth S. Thakar, Bijnan Bandyopadhyay, Prasanna Gandhi

    In this study, a new second order sliding mode controller is designed through a novel non‐linear sliding surface proposal for a slosh‐container system. A linear sliding surface based controller using second order sliding mode is also derived for the comparison purpose. Both the controllers need only output measurements. The super‐twisting algorithm is employed to ensure the finite time convergence of system trajectories to a second order sliding set. In sliding phase, the asymptotic stability of the system states to a desired origin is proved by proposing a new Lyapunov function for the system. A slosh‐container system representing underactuated interconnected non‐linear dynamics is considered. It is shown that how the consideration of limited track length of container affects the stability conditions. To generate a position trajectory for container from the control input signal, a new approach is employed for the implementation purpose. It is demonstrated through simulations and experimental results that the proposed controller based on the novel non‐linear sliding surface outperforms the other controller based on the linear surface and it is more suitable on various practical aspects. This also validates the theoretical findings of the study.


  • A New Nonlinear Control for Asymptotic Stabilization of a Class of Underactuated Systems: An Implementation to Slosh-Container Problem

    by Parth S. Thakar, Prasiddh K. Trivedi, Bijnan Bandyopadhyay, Prasanna S. Gandhi

    In this paper, a new control law is proposed for the nonlinear underactuated system. It is proved that the proposed control achieves asymptotic stability of the whole system. A broad class of underactuated systems, termed as commensurate underactuated systems, is identified where numbers of actuated and unactuated degrees of freedom are equal; for which the proposed control can be used as the general stabilizing control. The design methodology is simple and uses the prevalent total energy like Lyapunov function. The control strategy is tested on slosh-container system, a benchmark underactuated system of the class considered herein. We discern some important features of the proposed control law and analyze its effectiveness through physical interpretations. The findings are verified through simulations and experimental results for the slosh-container system.


  • Sliding mode control for underactuated slosh-container system using collocated and non-collocated linearization

    by Parth S Thakar, B. Bandyopadhyay, P. S. Gandhi

    This work mainly deals with the sliding mode control for the sloshing liquid in a container using Collocated and Non-Collocated linearization techniques. The comparative study of these techniques is done for the first time for a slosh-container system, which represents a class of underactuated systems. A linear sliding surface based sliding mode control is derived for both the approaches which rejects the matched uncertainties or model mismatches and disturbances. Some remarkable comparative points are noted and highlighted with the supporting simulations.


  • Sliding mode control for a class of underactuated systems using feedforward normal form: A slosh-container system

    by Parth S Thakar, B. Bandyopadhyay, P. S. Gandhi

    This paper deals with the design of stable sliding mode control (SMC) for the underactuated slosh-container system using feedforward normal form. A nonlinear coordinate transformation is used to convert the system into so called feedforward normal like form to decouple the control input appearing in one of the degree of freedom (DOF). This results in the design simplicity for the sliding mode control as well as the equivalent control and reduced order system derivation and its stability analysis. The range of surface parameters to provide the stable sliding motion for the system using proposed scheme, is also large compared to our earlier results. Simulation results are also presented to illustrate the proposed method.


  • Sliding mode control for an underactuated slosh-container system using non-linear model

    by Parth S. Thakar, B. Bandyopadhyay, P.S. Gandhi

    This work mainly deals with the sliding mode control for non-linear model of sloshing liquid in a container. Slosh coupled with container dynamics represents a class of underactuated systems with coupled non-linear equations. A pendulum model is used to model the lateral slosh. A linear sliding surface-based sliding mode control is derived. The reduced order system equation during sliding mode becomes non-linear when the non-linear system is constrained to the linear surface. Here a new method is proposed for the stability analysis of the reduced order non-linear system using Lyapunov stability theory. Simulations are carried out to validate the method. Experimental work is carried out to implement the designed sliding mode control strategy on the slosh-container system and corresponding results are also reported.


  • Robust control of rotary slosh using integral sliding modes

    by Parth S. Thakar, B. Bandyopadhyay, P. S. Gandhi, Shailaja Kurode

    This paper investigates a problem of control of rotary slosh using integral sliding modes (ISM). Slosh coupled with vehicle dynamics represents a class of systems having coupled nonlinear and underactuated dynamics. Rotary slosh is modeled using spherical pendulum. The coordinates are chosen to avoid the singularity at equilibrium point. A stabilizing control is designed using Lyapunov approach. A stabilizing controller (SC) is made robust by adding ISM component. The integral sliding mode control (ISMC) yields robust performance over the entire state space. The effectiveness of the method is validated in simulations.