Angelo Oreste Andrisano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Angelo Oreste Andrisano has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Marcello Pellicciari
Department of Sciences and Methods for Engineering, University of Modena and Reggio Emilia, Via Amendola 2, 42122 Reggio Emilia, Italy
8 shared publications - Francesco Leali
“Enzo Ferrari” Department of Engineering, University of Modena and Reggio Emilia, Modena, Italy
5 shared publications - Giovanni Berselli
Department of Mechanical Engineering, University of Genoa, Genoa, Italy
4 shared publications A. Toni
2 shared publications- Alberto Vergnano
Enzo Ferrari Department of Engineering, University of Modena and Reggio Emilia, Via P. Vivarelli 10, 41125 Modena, Italy
2 shared publications - Cristina Renzi
University of Modena and Reggio Emilia
2 shared publications
Latest Publications
- 20 September 2019
- Published by Springer Nature
- p. 741-752
A Multi-disciplinary Assessments Tool for Human-Machine Interaction
- 20 September 2019
- Published by Springer Nature
- p. 741-752
A Multi-disciplinary Assessments Tool for Human-Machine Interaction
- 2 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 19 (6) , 1882-1895
An Engineering Method for Comparing Selectively Compliant Joints in Robotic Structures
Large displacement compliant joints can substitute traditional kinematic pairs in robotic articulated structures for increasing ease-of-assembly, robustness, and safety. Nonetheless, besides their limited motion capabilities, compliant joints might be subjected to undesired spatial deformations which can deteriorate the system stability and performance whenever a low number of control inputs is available. In all these cases, it is convenient to select/design joint morphologies which enable a selectively compliant behavior, i.e., a low stiffness along a single desired direction. Within this context, this paper outlines an engineering method for quantifying the joint's selective compliance by means of local and global performance indices. The approach is validated by comparing two beam-like flexures whose analytic solution is known from the literature. Finally, two joint morphologies, previously employed in the fabrication of robotic/prosthetic hands, are critically compared on the basis of the proposed criteria.
- 2 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 19 (6) , 1882-1895
An Engineering Method for Comparing Selectively Compliant Joints in Robotic Structures
Large displacement compliant joints can substitute traditional kinematic pairs in robotic articulated structures for increasing ease-of-assembly, robustness, and safety. Nonetheless, besides their limited motion capabilities, compliant joints might be subjected to undesired spatial deformations which can deteriorate the system stability and performance whenever a low number of control inputs is available. In all these cases, it is convenient to select/design joint morphologies which enable a selectively compliant behavior, i.e., a low stiffness along a single desired direction. Within this context, this paper outlines an engineering method for quantifying the joint's selective compliance by means of local and global performance indices. The approach is validated by comparing two beam-like flexures whose analytic solution is known from the literature. Finally, two joint morphologies, previously employed in the fabrication of robotic/prosthetic hands, are critically compared on the basis of the proposed criteria.
- 15 February 2014
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 72 (1-4) , 403-418
A review on artificial intelligence applications to the optimal design of dedicated and reconfigurable manufacturing systems
- 15 February 2014
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 72 (1-4) , 403-418
A review on artificial intelligence applications to the optimal design of dedicated and reconfigurable manufacturing systems
- 3 April 2012
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 6 (4) , 251-263
Enhancing changeability of automotive Hybrid Reconfigurable Systems in digital environments
- 3 April 2012
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 6 (4) , 251-263
Enhancing changeability of automotive Hybrid Reconfigurable Systems in digital environments
- 1 December 2011
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 6 (1) , 17-27
Hybrid Reconfigurable System design and optimization through virtual prototyping and digital manufacturing tools
- 1 December 2011
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 6 (1) , 17-27
Hybrid Reconfigurable System design and optimization through virtual prototyping and digital manufacturing tools
- 24 March 2009
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 3 (2) , 81-91
Engineering method for adaptive manufacturing systems design
- 24 March 2009
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 3 (2) , 81-91
Engineering method for adaptive manufacturing systems design
- 1 January 2007
- Published by ASME International
- p. 525-533
Dynamic Optimization of Spur Gears
This paper presents a global optimization method able to find gear profile modifications that minimize vibrations. A non linear dynamic model is used to study the vibrational behavior; the dynamic model is validated using data available in literature. The optimization method takes into account the influence of torque levels both on the static and the dynamic response. Therefore, two different objective functions are considered; the first one is based on static analysis and the second one is based on the dynamic behavior of a lumped mass system. The procedure can find the optimal profile modification that reduce the vibrations over a wide range of operating conditions. In order to reduce the computational cost, a Random-Simplex optimization algorithm is developed; the optimum reliability is also estimated using a Monte Carlo simulation. The approach shows good performances both for the computational efficiency and the reliability of results.
- 1 January 2007
- Published by ASME International
- p. 525-533
Dynamic Optimization of Spur Gears
This paper presents a global optimization method able to find gear profile modifications that minimize vibrations. A non linear dynamic model is used to study the vibrational behavior; the dynamic model is validated using data available in literature. The optimization method takes into account the influence of torque levels both on the static and the dynamic response. Therefore, two different objective functions are considered; the first one is based on static analysis and the second one is based on the dynamic behavior of a lumped mass system. The procedure can find the optimal profile modification that reduce the vibrations over a wide range of operating conditions. In order to reduce the computational cost, a Random-Simplex optimization algorithm is developed; the optimum reliability is also estimated using a Monte Carlo simulation. The approach shows good performances both for the computational efficiency and the reliability of results.
- 8 March 2004
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
On Tire Monitoring Systems Temperature Compensation
Direct type [1] Tire Monitoring Systems supervise tire internal inflating pressure. The authors previously proved that Tire Monitoring must be focused on the tire (i.e.: vehicle) dynamic behaviour [2]: the real aim of the supervising action. In this case, even the external absolute pressure must be taken into account. NHTSA studies showed improper warnings must be avoided in order to keep the driver confidence with the system; internal temperature decrease is the Tire Monitoring Systems' main cause of improper warnings. A new approach for optimal Tire Monitoring Systems temperature compensation related to external environmental temperature, able to avoid improper warnings, will be presented.
- 8 March 2004
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
On Tire Monitoring Systems Temperature Compensation
Direct type [1] Tire Monitoring Systems supervise tire internal inflating pressure. The authors previously proved that Tire Monitoring must be focused on the tire (i.e.: vehicle) dynamic behaviour [2]: the real aim of the supervising action. In this case, even the external absolute pressure must be taken into account. NHTSA studies showed improper warnings must be avoided in order to keep the driver confidence with the system; internal temperature decrease is the Tire Monitoring Systems' main cause of improper warnings. A new approach for optimal Tire Monitoring Systems temperature compensation related to external environmental temperature, able to avoid improper warnings, will be presented.