SPSubrata Kumar Panda

Subrata Kumar Panda

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Subrata Kumar Panda has a total of 190 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Dynamic response of PLA honeycomb core GFRP sandwich panels with an additively manufactured core: Experimental characterization and numerical blast analysis

    by Niladri Dey, Manish Kumar Gouda, Ashish Kumar Meher, Anway Rajendra Walke, Subrata Kumar Panda

    This study investigates the transient dynamic response of an additively manufactured polylactic acid (PLA) honeycomb sandwich panel with glass-fiber-reinforced plastic (GFRP) face sheets through experimental characterization and finite element analysis. The PLA honeycomb core was fabricated using fused deposition modelling, while the GFRP face sheets were prepared using the hand lay-up technique. Tensile, flexural, and density tests were conducted to experimentally characterize the material properties used in the numerical model. A finite element model was developed in ANSYS using the experimentally obtained effective properties and was initially assessed against benchmark results reported in the literature. The experimental and numerical displacement–time histories under cantilever harmonic excitation at 500 Hz and 0.2 N showed similar trends for the investigated laboratory condition. A separate numerical calculation was performed to examine the early-time global displacement response under a hypothetical prescribed modified Friedlander pressure pulse using a linear-elastic material representation. The blast analysis showed maximum deformation in the central region of the panel and relatively lower displacement near the supported boundaries. Within the 30 ms simulation window, the panel exhibited a bounded transient displacement response. The blast calculations represent early-time global displacement predictions under the assumption of a linear-elastic material. Failure initiation, progressive stiffness degradation, core crushing, and interfacial separation were not modelled, and energy absorption was not quantified. Accordingly, the calculated histories do not establish retained structural integrity or validated blast-protection performance. The study provides experimental characterization and a laboratory assessment of the global dynamic response of the investigated configuration, along with preliminary elastic calculations under the prescribed pressure pulse.

  • Effect of delamination damage and sensitivity behaviour on stress and deformation characteristics of sandwich structure

    by Naveen Kumar Akkasali, Ashish Kumar Meher, Gaurav Kumar, Subrata Kumar Panda

  • Hybrid Computational Model (FE and ANN) for Prediction of Modal Frequency Response of Damaged Hyperelastic (Hydrogel) Panel Structure

    by Ashish Kumar Meher, Naveen Kumar Akkasali, Gaurav Kumar, Subrata Kumar Panda

    This study presents an integrated finite element (FE) and artificial neural network (ANN) framework for predicting the modal frequency response of damaged agar-based hydrogel plates under varying geometry, boundary conditions, and damage severity. The aim of the work is to develop a computationally efficient hybrid methodology in which validated FE simulations are used to generate a reliable dataset, and ANN-based surrogate models are subsequently employed for rapid frequency prediction. The hydrogel material parameters were obtained from experimental compression data through curve fitting using an Ogden-type hyperelastic model. Thereafter, the frequency characteristics were computed using ABAQUS-based FE analysis, and the numerical consistency was ensured through mesh convergence and validation studies. A systematic parametric investigation was conducted by varying stiffness-sensitive parameters, namely aspect ratio, thickness ratio, boundary conditions, and damage length, to establish physically consistent frequency trends. Unlike earlier studies that mainly focus on either numerical simulation or data-driven prediction independently, the present work combines FE-based modal analysis with ANN surrogate modelling for frequency-based assessment of damage-induced stiffness degradation in hydrogel plates. Based on the generated dataset, five ANN surrogate configurations were trained and compared to identify the most efficient prediction model. The proposed FE-ANN workflow enables rapid frequency estimation and reduces the need for repeated FE simulations. The frequency increased from 6.4977 Hz to 30.093 Hz when the aspect ratio changed from 1 to 3.

  • Influence of Concentric Cutouts on Axially Compressed Laminated Shell Panel Buckling Behavior

    by Hukum Chand Dewangan, Nitin Sharma, Prashik Malhari Ramteke, Subrata Kumar Panda

    This study presents a numerical assessment of the critical buckling behavior of various geometrical configurations of laminated composite flat/curved panels featuring concentric cutouts of different shapes and dimensions. A finite element formulation, incorporating higher-order kinematic assumptions, is employed to model the multi-layered structure with accuracy. An isoparametric element framework is used to simulate the panel geometry, with the cutout represented through a quarter-plate modeling technique and extended to form the complete configuration. The approach is verified by benchmarking its results against those available in the published literature. The predicted normalized critical buckling loads show excellent agreement with three-dimensional elasticity with deviations generally within ±2%. In contrast, classical laminate plate theory (CLPT) exhibits significantly larger deviations reaching up to about 38%, highlighting the importance of higher-order shear deformation effects. Also, the present HSDT predictions differ by only 0.86–6.99% from experimental results. The model is further tested for its adaptability across various geometrical forms, such as flat plates, cylindrical, spherical, hyperbolic and elliptical surfaces, under different material systems and boundary settings. The findings highlight the significance of using a higher-order numerical strategy in predicting accurate modal characteristics of perforated laminated composites. A series of case studies is conducted to examine the influence of critical design parameters such as aspect ratio, thickness, curvature and boundary conditions. The study underscores the necessity of advanced modeling techniques for effective structural analysis of composite components with geometric discontinuities.

  • Influence of damage (delamination) on modal responses of sandwich composite panel-numerical and experimental analysis

    by Naveen Kumar Akkasali, Trupti Ranjan Mahapatra, Gaurav Kumar, Usha Rani Sahoo, Ashish Kumar Meher, Subrata Kumar Panda

    The current research numerically investigates the influence of delamination on the natural frequencies of intact and delaminated glass fiber–reinforced composite (GFRC) sandwich panels. The sandwich structure synthesized via the hand lay-up method consists of two laminated GFRC face sheets bonded to an isotropic cured epoxy core. The results obtained using the present finite element (FE) model implemented in ABAQUS are compared to previous numerical and current experimental findings, demonstrating that the model functions consistently, with major differences of 10.77% and 14.84% found in a few modes. This validated FE model is used to systematically evaluate the influence of boundary conditions, fiber orientation, aspect ratio, core-to-face thickness ratio, and delamination shape on natural frequencies. Results show that fully clamped plates exhibit the highest frequencies, but are also most sensitive to delamination, with reductions approaching 50% in specific modes. Increasing the core-to-face thickness ratio significantly enhances modal performance, yielding up to 29% improvement in higher modes. The unidirectional fiber ([0°/0°] S ) configuration with a core-to-face thickness ratio of 3 offers peak modal performance, with Mode 5 frequencies improving by over 29% and 20%, in intact and delaminated states, respectively. Among all shapes, the rectangular delamination produces the highest natural frequencies, while the square shape results in the lowest overall values. Notably, circular delamination leads to a 16.6% drop in Mode 5, demonstrating strong higher-mode sensitivity to delamination geometry. The findings provide design guidelines for optimizing stiffness and vibration resilience in GFRC sandwich structures.

  • Influence of damage assessment on mechanical stress and deformation responses of porous graded curved (single/doubly) panel structure

    by Vikash Kumar, Subrata K. Panda, Rama Chandra Pradhan, Ashish Kumar Meher, S. S. K. Deepak

    The present study develops a numerical solution technique to assess the impact of damage, curvature, and porosity on the functionally graded material (FGMs) structure. Initially, the structural model is derived mathematically using higher‐order kinematics in this framework of a corresponding single‐layer theory. The structural model is derived mathematically, and the deflection and stress values are obtained computationally using in‐house MATLAB code. Primarily, the concurrence behavior of the developed model is checked, and further, the accuracy of the present model is verified by contrasting the outcomes with the data existing in the open domain. The maximum deviation observed between the reference and present results in stress and deflection responses is 7.1% and 2.68%, respectively. The validated model is further utilized to understand the effects of different geometrical porosity distributions, damages, and shapes.

  • Numerical and Experimental Modal Analysis of Damaged Soft Panel (Hydrogel) Structure using Nonlinear Material Model

    by Ashish Kumar Meher, Pradosh Pritam Dash, Gaurav Kumar, Subrata Kumar Panda

    This study presents a detailed investigation of the modal frequency responses of agar-based hydrogel flat components using both numerical and experimental approaches. A finite element-based numerical model is developed, incorporating the nonlinear mechanical behavior of the hydrogel material along with appropriate geometric dimensions and boundary conditions. The first ten frequency modes are evaluated for both damaged and undamaged panels. Experimental tests have also been performed to validate the proposed numerical results with an average deviation of 6.124%, further confirming the model’s reliability and accuracy. Additionally, variable parametric studies have investigated the impact of varying aspect ratios, thickness ratios, and boundary conditions on the natural frequencies of the hydrogel flat components. Due to damage, the frequency decreases by up to 10% compared to intact conditions. The influence of damage on structural integrity and the local stiffness degradation highlights the sensitivity of the hydrogel’s frequency behavior.

  • Numerical Prediction of Deflection and Stress Responses of Damaged Hybrid Single-Lap Joint Components and Experimental Verification

    by Naveen Kumar Akkasali, Ashish Kumar Meher, Gaurav Kumar, Subrata Kumar Panda

    This research reported the deflection and stress behavior of a hybrid single-lap adhesively bonded joint, accounting for numerical damage. For the numerical analysis, a computer-aided engineering (CAE) model has been developed in ABAQUS for four different cases: single-lap adhesive joints (SLAJ), their delaminated counterparts (SLAJ-D), hybrid single-lap adhesive joints (HSLAJ) and hybrid delaminated joints (HSLAJ-D). The model adequacy, including solution stability, has been verified by comparing the results with published results, in-house experimental values, and mesh independence tests. Experimental validations are presented for all joint types, with numerical values closely matching the experimental data at higher loading conditions but not at lower ones. Tensile tests conducted on HSLJ and HSLJ-D indicate that HSLJ-D exhibits superior load-bearing capacity, achieving higher tensile loads of 5430 N and 5290 N compared to HSLJ. The numerical validation shows a maximum deviation of 8.63% when compared with the literature data. The developed numerical model predicts the deflection results in close agreement with the experimental data, with a minimum deviation of 0.381% and a maximum deviation of 13.556%. Further, the CAE model is extended to compute both deflections and stress data by varying the parameters (related to joint geometry and damage), which affect the stiffness values (fiber orientation, aspect ratio, core-to-face seat thickness ratio, delamination shape). Finally, the influence of all parameters on the mid-span deflection and adhesive stresses is discussed, demonstrating that the bolted-bonded configuration significantly enhances overall structural stiffness and strength.


  • Synthesis and mechanical characterization of hybrid (chitosan–MWCNT-reinforced epoxy) polymeric nanocomposite and low load applications

    by Ranva Sai Sahithi, Usha Rani Sahoo, Naveen Kumar Akkasali, Trupti Ranjan Mahapatra, Ashish Kumar Meher, Gaurav Kumar, Subrata Kumar Panda