Thomas J. Hughes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Thomas J. Hughes has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Eric F. May
Department of Chemical Engineering, The University of Western Australia, Crawley, WA 6009, Australia
20 shared publications Eric F. May
14 shared publicationsKenneth N. Marsh
14 shared publications- Brendan Francis Graham
Fluid Science and Resources Division, School of Mechanical and Chemical Engineering, The University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009, Australia
10 shared publications - Saif. Z. S. Al Ghafri
Fluid Science and Resources Division, School of Engineering, University of Western Australia 1 , 35 Stirling Hwy, Crawley, 6009 Perth, Australia
7 shared publications Michael L. Johns
6 shared publications
Latest Publications
- Open Access
- 10 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 248
Numerical insights into rotary sloshing dynamics of liquid hydrogen in spherical tanks under transient excitation
- 10 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 248
Open AccessNumerical insights into rotary sloshing dynamics of liquid hydrogen in spherical tanks under transient excitation
- Open Access
- 30 August 2025
- Published by Elsevier in Energy Conversion and Management
- Vol. 346
A net-zero polygeneration system for power, hydrogen and ammonia: energy, exergy and exergoeconomic (3E) analyses
- 30 August 2025
- Published by Elsevier in Energy Conversion and Management
- Vol. 346
Open AccessA net-zero polygeneration system for power, hydrogen and ammonia: energy, exergy and exergoeconomic (3E) analyses
- Open Access
- 25 April 2025
- Published by Elsevier in Journal of Cleaner Production
- Vol. 510
Multi-stage extraction process to produce enhanced biocrude from solid waste liquefaction
- 25 April 2025
- Published by Elsevier in Journal of Cleaner Production
- Vol. 510
Open AccessMulti-stage extraction process to produce enhanced biocrude from solid waste liquefaction
- Open Access
- 28 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 256
Thermodynamic modelling of low fill levels in cryogenic storage tanks for application to liquid hydrogen maritime transport
- 28 July 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 256
Open AccessThermodynamic modelling of low fill levels in cryogenic storage tanks for application to liquid hydrogen maritime transport
- 23 March 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 62, 1273-1285
Thermodynamic modelling of pressurised storage and transportation of liquid hydrogen for maritime export
- 23 March 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 62, 1273-1285
Thermodynamic modelling of pressurised storage and transportation of liquid hydrogen for maritime export
- Open Access
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Thermal stratification and pressure evolution in large-scale liquid hydrogen storage
One of the barriers to large-scale liquid hydrogen (LH2) export is the high capital cost of high-performance insulation systems, requiring double-walled tanks to minimise boil-off rate (BOR). Unlike ground-based tanks, a commercial LH2 carrier is expected to utilise boil-off gas (BOG) for propulsion and onboard power. Sizing insulation to match steady-state BOR with BOG utilisation is not feasible, since steady-state heat transfer may not be achieved during a 2 – 3 week voyage. This is partly due to the large thermal mass of the tank relative to LH2. Furthermore, full utilisation of BOR for propulsion is not expected to occur until after 1 – 2 days when the ship is travelling on open seas. This study investigates transient pressure evolution within large spherical LH2 tanks using a lumped-mass analytical model, validated against experimental and CFD data. The model accounts for stratification within the liquid and vapour phases by considering wall boundary layer flow. For large tanks, a significantly greater pressure rise than would be expected for an isothermal, saturated mixture. Tank insulation is modelled in 2D to allow for non-uniform heat transfer, for various types of bulk insulation. Top-biased heating in particular is predicted to cause a greater pressure rise, driven by conduction heat transfer through transfer lines and support structures. The study also investigates induced mixing as a means to bring the liquid closer to an isothermal state, causing condensation in the vapour and lowering pressure. This could be used intermittently to delay the venting of BOG during the early stages of a voyage, reducing the thermal performance requirements for tank insulation.
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessThermal stratification and pressure evolution in large-scale liquid hydrogen storage
One of the barriers to large-scale liquid hydrogen (LH2) export is the high capital cost of high-performance insulation systems, requiring double-walled tanks to minimise boil-off rate (BOR). Unlike ground-based tanks, a commercial LH2 carrier is expected to utilise boil-off gas (BOG) for propulsion and onboard power. Sizing insulation to match steady-state BOR with BOG utilisation is not feasible, since steady-state heat transfer may not be achieved during a 2 – 3 week voyage. This is partly due to the large thermal mass of the tank relative to LH2. Furthermore, full utilisation of BOR for propulsion is not expected to occur until after 1 – 2 days when the ship is travelling on open seas. This study investigates transient pressure evolution within large spherical LH2 tanks using a lumped-mass analytical model, validated against experimental and CFD data. The model accounts for stratification within the liquid and vapour phases by considering wall boundary layer flow. For large tanks, a significantly greater pressure rise than would be expected for an isothermal, saturated mixture. Tank insulation is modelled in 2D to allow for non-uniform heat transfer, for various types of bulk insulation. Top-biased heating in particular is predicted to cause a greater pressure rise, driven by conduction heat transfer through transfer lines and support structures. The study also investigates induced mixing as a means to bring the liquid closer to an isothermal state, causing condensation in the vapour and lowering pressure. This could be used intermittently to delay the venting of BOG during the early stages of a voyage, reducing the thermal performance requirements for tank insulation.
- 27 July 2021
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 66 (11) , 4103-4111
High-Pressure Melting Temperature Measurements in Mixtures Relevant to Liquefied Natural Gas Production and Comparisons with Model Predictions
- 27 July 2021
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 66 (11) , 4103-4111
High-Pressure Melting Temperature Measurements in Mixtures Relevant to Liquefied Natural Gas Production and Comparisons with Model Predictions
- 30 January 2020
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 65 (2) , 906-915
High-Pressure Thermal Conductivity Measurements of a (Methane + Propane) Mixture with a Transient Hot-Wire Apparatus
- 30 January 2020
- Published by American Chemical Society (ACS) in Journal of Chemical & Engineering Data
- Vol. 65 (2) , 906-915
High-Pressure Thermal Conductivity Measurements of a (Methane + Propane) Mixture with a Transient Hot-Wire Apparatus