Veronica Eliasson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Veronica Eliasson has a total of 111 co-authors. Here are the top co-authors by number of shared publications:
Finnegan Wilson
Mechanical Engineering Department, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401, U.S.A.
6 shared publications- Dylan Jacob Kline
Physical and Life Sciences Directorate, Lawrence Livermore National Laboratory, Livermore, USA
5 shared publications - Finnegan Wilson
Mechanical Engineering Department, Colorado School of Mines, Golden, USA
5 shared publications Grace I. Rabinowitz
Mechanical Engineering Department Colorado School of Mines Colorado USA
4 shared publicationsH. Jeon
University of Southern California
4 shared publications- Kyle T. Sullivan
Physical and Life Sciences Directorate, Lawrence Livermore National Laboratory, Livermore, USA
4 shared publications
Latest Publications
- Open Access
- 1 February 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (02) , P02043
Monte Carlo simulation methodology for characterizing the energy response function and resolving power of a digital Flat Panel Detector (FPD) assembly
The use of high-resolution, digital flat panel detectors (FPDs) makes quantitative assessments of radiographic and 3D tomographic representations feasible. However, the energy response function and spatial resolving power of the detector must be known. Here, we present a methodology for characterizing an FPD assembly using Monte Carlo simulations. The detector assembly modeled here was fielded in the 3-Ring Flash X-ray Imaging System designed and built at Lawrence Livermore National Laboratory (LLNL), which employs fifteen Carestream ® HPX-DR3543 FPDs enclosed in protective housings. Detailed Monte Carlo (MCNP6) simulations of an as-fielded detector assembly were performed to estimate its energy response function in terms of analog-to-digital unit (ADU) “counts” per pixel per incident x-ray as a function of energy up to ∼ 500 keV and its theoretical (idealized) resolving power. The practical resolving power of the FPD assembly in a realistic scenario was then estimated by simulating radiographic images of a variant of the United Kingdom (U.K.) “Kaleidoscope” resolution target.
- 1 February 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (02) , P02043
Open AccessMonte Carlo simulation methodology for characterizing the energy response function and resolving power of a digital Flat Panel Detector (FPD) assembly
The use of high-resolution, digital flat panel detectors (FPDs) makes quantitative assessments of radiographic and 3D tomographic representations feasible. However, the energy response function and spatial resolving power of the detector must be known. Here, we present a methodology for characterizing an FPD assembly using Monte Carlo simulations. The detector assembly modeled here was fielded in the 3-Ring Flash X-ray Imaging System designed and built at Lawrence Livermore National Laboratory (LLNL), which employs fifteen Carestream ® HPX-DR3543 FPDs enclosed in protective housings. Detailed Monte Carlo (MCNP6) simulations of an as-fielded detector assembly were performed to estimate its energy response function in terms of analog-to-digital unit (ADU) “counts” per pixel per incident x-ray as a function of energy up to ∼ 500 keV and its theoretical (idealized) resolving power. The practical resolving power of the FPD assembly in a realistic scenario was then estimated by simulating radiographic images of a variant of the United Kingdom (U.K.) “Kaleidoscope” resolution target.
- 24 November 2025
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 51 (2) , 224-234
Small‐Scale Exploding Wire Experiments of Blast Wave Propagation in Tunnels
Underground storage of energetic materials in confined spaces, such as in mining operations, requires careful safety assessments to protect workers, equipment, and surrounding structures in the event of an accidental explosion. Understanding how blast waves propagate and attenuate through tunnels and intersections is critical for these assessments. Data for such scenarios can be obtained from both full‐scale and small‐scale tests. While full‐scale tests provide higher fidelity, small‐scale experiments are generally safer, less costly, less time consuming, and allow for more repetitions. When appropriate scaling techniques are applied, small‐scale tests can yield reliable results and help with trends and increased understanding of the shock dynamics event. In this work, exploding wires were employed as a controllable and repeatable energy source to investigate blast wave propagation in three representative geometries: a straight tunnel, a four‐way intersection, and a chamber connected to a tunnel. Side‐on overpressure measurements were collected alongside high‐speed schlieren photographs to capture shock evolution and reflections. The experiments demonstrated excellent repeatability, with standard deviations as low as 0.28 kPa, and revealed systematic effects of wall roughness and geometry on attenuation and shock front behaviors. Results scaled using Hopkinson–Cranz cube‐root scaling laws modified with an energy concentration factor to account for the confinement of the tunnels, showing agreement with some published high‐explosive data. These findings highlight the utility of exploding wire techniques for generating reliable confined‐blast datasets, supporting both hazard assessment and model validation for underground explosion safety.
- 24 November 2025
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 51 (2) , 224-234
Small‐Scale Exploding Wire Experiments of Blast Wave Propagation in Tunnels
Underground storage of energetic materials in confined spaces, such as in mining operations, requires careful safety assessments to protect workers, equipment, and surrounding structures in the event of an accidental explosion. Understanding how blast waves propagate and attenuate through tunnels and intersections is critical for these assessments. Data for such scenarios can be obtained from both full‐scale and small‐scale tests. While full‐scale tests provide higher fidelity, small‐scale experiments are generally safer, less costly, less time consuming, and allow for more repetitions. When appropriate scaling techniques are applied, small‐scale tests can yield reliable results and help with trends and increased understanding of the shock dynamics event. In this work, exploding wires were employed as a controllable and repeatable energy source to investigate blast wave propagation in three representative geometries: a straight tunnel, a four‐way intersection, and a chamber connected to a tunnel. Side‐on overpressure measurements were collected alongside high‐speed schlieren photographs to capture shock evolution and reflections. The experiments demonstrated excellent repeatability, with standard deviations as low as 0.28 kPa, and revealed systematic effects of wall roughness and geometry on attenuation and shock front behaviors. Results scaled using Hopkinson–Cranz cube‐root scaling laws modified with an energy concentration factor to account for the confinement of the tunnels, showing agreement with some published high‐explosive data. These findings highlight the utility of exploding wire techniques for generating reliable confined‐blast datasets, supporting both hazard assessment and model validation for underground explosion safety.
- 25 September 2025
- Published by Springer Nature in Experimental Techniques
- Vol. 50 (4) , 599-610
An Analysis of Input Parameters for Film-Based Flash X-Ray Radiography
- 25 September 2025
- Published by Springer Nature in Experimental Techniques
- Vol. 50 (4) , 599-610
An Analysis of Input Parameters for Film-Based Flash X-Ray Radiography
- 1 August 2025
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 50 (10) , 21-31
Development of a Printable Prill Formulation Technique and Demonstration of Monomodal Prill Size on Compaction Density and Compressive Strength
Polymer‐bonded explosive molding powder, or “prills,” are relied on for the fabrication of pressed high explosives since the 1950's. The wet granulation technique, also known as “slurry coating,” that is used to formulate prills, is a complex process that results in polydisperse and variable yields. This makes it difficult to study the mesoscale effect that prills have on the microstructure of a pressed article. The following study introduces a novel approach to energetic granulation that leverages techniques used in the additive manufacturing of paste‐like energetic materials. This extrusion granulation, or prill printing technique, makes it possible to tailor the sizes and shapes of prills, allowing for their morphological influences to be studied in a controlled manner. The following work details the fabrication and characterization of four monomodal size lots of prills using an inert formulation (95 wt.% melamine, 5 wt.% polymer binder). Prills from each size lot were die‐pressed using a fixed recipe to investigate how prill size impacts compaction density and therefore compressive strength. It was found that larger prills influence the pressing density by creating larger defects within the microstructure of a pressed article, resulting in a decrease in compressive strength.
- 1 August 2025
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 50 (10) , 21-31
Development of a Printable Prill Formulation Technique and Demonstration of Monomodal Prill Size on Compaction Density and Compressive Strength
Polymer‐bonded explosive molding powder, or “prills,” are relied on for the fabrication of pressed high explosives since the 1950's. The wet granulation technique, also known as “slurry coating,” that is used to formulate prills, is a complex process that results in polydisperse and variable yields. This makes it difficult to study the mesoscale effect that prills have on the microstructure of a pressed article. The following study introduces a novel approach to energetic granulation that leverages techniques used in the additive manufacturing of paste‐like energetic materials. This extrusion granulation, or prill printing technique, makes it possible to tailor the sizes and shapes of prills, allowing for their morphological influences to be studied in a controlled manner. The following work details the fabrication and characterization of four monomodal size lots of prills using an inert formulation (95 wt.% melamine, 5 wt.% polymer binder). Prills from each size lot were die‐pressed using a fixed recipe to investigate how prill size impacts compaction density and therefore compressive strength. It was found that larger prills influence the pressing density by creating larger defects within the microstructure of a pressed article, resulting in a decrease in compressive strength.
- Open Access
Tool changing and tool sharing system for interconnected multi-material direct ink write 3D printers
- 18 February 2025
- Published by Springer Nature in Experimental Techniques
- p. 1-13
Quantitative Comparisons of Image Quality for Flash X-Ray Detectors
- 18 February 2025
- Published by Springer Nature in Experimental Techniques
- p. 1-13
Quantitative Comparisons of Image Quality for Flash X-Ray Detectors
- 1 January 2025
- Published by Optica Publishing Group
- p. RTh1E.3
A Quantitative Comparison of Digital Detector, Computed Radiography, and Film for Flash X-ray Radiography Detection
Image quality metrics were explored across a range of detectors and parameters with a 450kVp flash X-ray system. Peak voltage, film pack assembly, source filtering, and detector choice were investigated for individual and interacting effects.
- 1 January 2025
- Published by Optica Publishing Group
- p. RTh1E.3
A Quantitative Comparison of Digital Detector, Computed Radiography, and Film for Flash X-ray Radiography Detection
Image quality metrics were explored across a range of detectors and parameters with a 450kVp flash X-ray system. Peak voltage, film pack assembly, source filtering, and detector choice were investigated for individual and interacting effects.
- 21 October 2024
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 11 (2) , 198-211
Modification of Jet Velocities in an Explosively Loaded Copper Target with a Conical Cavity
- 21 October 2024
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 11 (2) , 198-211
Modification of Jet Velocities in an Explosively Loaded Copper Target with a Conical Cavity
- Open Access
Modification of Jet Velocities in an Explosively Loaded Copper Target with a Conical Defect
In this work, the design and execution of an experiment with the goal of demonstrating control over the evolution of a copper jet is described. Simulations show that when using simple multi-material buffers placed between a copper target with a conical defect and a cylinder of high-explosive, a variety of jetting behaviors occur based on material placement, including both jet velocity augmentation and mitigation. A parameter sweep was performed to determine optimal buffer designs in two configurations. Experiments using the optimal buffer designs verified the effectiveness of the buffer and validated the modeling.
Open AccessModification of Jet Velocities in an Explosively Loaded Copper Target with a Conical Defect
In this work, the design and execution of an experiment with the goal of demonstrating control over the evolution of a copper jet is described. Simulations show that when using simple multi-material buffers placed between a copper target with a conical defect and a cylinder of high-explosive, a variety of jetting behaviors occur based on material placement, including both jet velocity augmentation and mitigation. A parameter sweep was performed to determine optimal buffer designs in two configurations. Experiments using the optimal buffer designs verified the effectiveness of the buffer and validated the modeling.
- Open Access
Dual feed progressive cavity pump extrusion system for functionally graded direct ink write 3D printing