RRRaymond C. Rumpf

Raymond C. Rumpf

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Raymond C. Rumpf has a total of 56 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Conformal Frequency Selective Surfaces for Arbitrary Curvature

    by Cesar L. Valle, Gilbert T. Carranza, Raymond C. Rumpf

    An algorithm is introduced for generating frequency selective surfaces (FSS) capable of conforming to any curvature while maintaining proper size, shape and spacing of the elements. Compared to traditional projection and mapping methods, the presented algorithm maintains the electromagnetic properties of the FSS array despite the curvature. The algorithm can be used to conform to radomes, parts of autonomous vehicles, or any surface. The algorithm is agnostic to both element design and surface curvature. This allows the user to design a FSS for any curved surface while maintaining its response comparable to a flat array. The algorithm outputs two standard tessellation language (STL) files, one describing the curved surface and the other the elements of the FSS placed onto the curved surface. This makes the algorithm suitable for 3D printing using systems with more than three axes or for flexible electronics. Several examples of arbitrary surfaces are shown. Lastly, the algorithm was applied to a Jerusalem-cross FSS on a non-symmetrical parabolic dome. The dimensions of the parabolic dome were chosen to test the response of the array on a rather extreme surface against a projected array on the same surface. Simulations were carried out using Ansys HFSS from the infinite array to finite arrays to confirm operation. Three test surfaces were manufactured with measured results found to be in good agreement with simulation.


  • Formulation of Iterative Finite-Difference Method for Generating Large Spatially Variant Lattices

    by Manuel F. Martinez, Jesus J. Gutierrez, Jimmy E. Touma, Raymond C. Rumpf

    A new numerical method to generate spatially variant lattices (SVLs) is derived and implemented. The algorithm proposed solves the underlying partial differential equations iteratively with an update equation derived using the finite-difference method to obtain an SVL that is continuous, smooth, and free of unintended defects while maintaining the unit cell geometry throughout the lattice. This iterative approach is shown to be more memory-efficient when compared to the matrix-based approach and is, thus, suitable for the calculation of large-scale SVLs. The iterative nature of the solver allows it to be easily implemented in graphics processing unit to parallelize the computation of SVLs. Two spatially variant self-collimating photonic crystals are generated and simulated to demonstrate the functionality of the algorithm as a tool to generate fully three-dimensional photonic devices of realistic size.

  • Open Access

    Dynamical Control of Multilayer Spacetime Structures Using Extended Fourier Modal Method

    by Yaser Khorrami, Davood Fathi, Amin Khavasi, Raymond C. Rumpf

    We introduce two-dimensional space plus time (2D+1) structure and numerically investigate it using a developed multilayer simulation framework, for the first time. The new structure is consisting of crossed grating with time-varying permittivity which is inspired from 1D+1. In this regard, we extend Fourier Modal Method (FMM) in a general approach for spacetime multilayer states. Our proposed framework is fast, robust, and powerful compared to various finite difference methods. We use the scattering matrix technique to develop the proposed spacetime simulation method for multilayer structures using a non-uniform stack of layers. The method is perfectly suitable to investigate the spatiotemporal effects of surfaces/metasurfaces which covers both the transverse electric and magnetic (TE & TM) polarizations. The results show more freedom to control the optical outcomes of the multilayer considering two spatial periodicities in addition to the modulation frequency to reach nonreciprocity as one of the main consequences of the proposed structure. Moreover, we investigate the condition and limitation of breaking the Lorentz rule for spacetime structures. 2D+1 structure is more controllable than the 1D+1 due to its greater ability to adjust spatial manipulation in addition to temporal variations to reach nonreciprocity applications, digital coding, beam steering, etc.


  • Photon Funnel Design Based on Spatially Variant Self-Collimating Photonic Crystals

    by Noel P. Martinez, Chun Xia, Stephen M. Kuebler, Raymond C. Rumpf

    We present a device that flows a beam incident at any position and angle along the input side of a lattice to a single zone at the output. We report the performance of the device.

  • Experimental Demonstration Of Broadband Self-Collimation Effect In 3d Hexagonal Lattice Fabricated Using A Low-Refractive-Index Polymer

    by Chun Xia, Stephen M. Kuebler, Noel P. Martinez, Manuel Martinez, Raymond C. Rumpf, Jimmy Touma

    Wide-angle self-collimation from the E- to L-band is experimentally demonstrated in a hexagonal lattice of air-holes fabricated in a low-refractive-index medium by multiphoton lithography.

  • Guided-mode resonance filter optimal inverse design using one- and two-dimensional grating

    by Yaser Khorrami, Davood Fathi, Raymond C. Rumpf

    We propose an optimized method for the inverse design of guided-mode resonance (GMR) filters using one- and two-dimensional (1D and 2D) grating structures. This work for 2D state is based on developing the effective permittivity of 1D grating structures along three orthogonal axes to predict the physical dimensions of the structure, for the first time to our knowledge. Also, we compare three optimization methods to reach the optimized conditions based on the characteristics of multilayer structures. Both the transfer matrix method and rigorous coupled-wave analysis are used to simulate and show the reflection and transmission of the proposed 2D GMR filters. The results show that insensitivity to polarization, the best accuracy in resonance location design, and a high quality factor can be achieved for both the rectangular and cylindrical structures as the ideal 2D GMR filters. Also, the effect of each layer thickness on the resonance location and the full width at half-maximum is illustrated. Finally, we investigate three different reasons for decreasing the FWHM of the output reflection of the GMR filters.


  • Open Access

    GENERATING SPATIALLY-VARIANT METAMATERIAL LATTICES DESIGNED FROM SPATIAL TRANSFORMS

    by Eric A. Berry, Raymond C. Rumpf

    Spatial transform techniques like transformation optics and conformal mapping have arisen as the dominant techniques for designing metamaterial devices. However, these techniques only produce the electrical permittivity and permeability as a function of position. The manner in which these functions are converted into physical metamaterial lattices remains elusive, except in some simple or canonical configurations. Metamaterial lattices designed by spatial transforms are composed of elements of different sizes, orientations, and designs. The elements must be distributed and oriented in a manner that makes the final lattice smooth, continuous, have uniform density, be free of unintentional defects, and have minimal distortions to the elements. Any of these would weaken or destroy the electromagnetic properties of the lattice. This paper describes a general purpose method to generate such arbitrary metamaterial lattices. Inputs to the algorithm are the permittivity and permeability functions as well as the baseline metamaterials that can provide the necessary permittivity and permeability values. In prior research, we reported a simple finite-difference technique for calculating the permittivity and permeability functions for arbitrary shaped devices using transformation optics. The methodology presented in this work is illustrated by generating an electromagnetic cloak of arbitrary shape that was designed using the previously reported technique. The final metamaterial cloak is simulated using the finite-difference time-domain method and performance compared to other cloaks reported in the literature.


  • Automated Hybrid 3-D Printing of 3-D Meandering Interconnects

    by Ubaldo Robles, Andelle Kudzal, Raymond C. Rumpf

    In this work, a completely automated CAD-to-print process flow for hybrid direct-write 3D printing was produced. We adapted this capability to manufacture a meandering conductive trace formed into a meandering arbitrary interconnect in shape of a 3D pretzel that is completely embedded in dielectric. The conversion between g-code and pgm-code was demonstrated for hybrid 3D printing between metal and dielectric materials. This research produced a reliable automated process that can potentially be used to manufacture arbitrary 3D circuits. This research also identified the need for better slicing techniques for hybrid manufacturing of interconnects.


  • Design and Hybrid Additive Manufacturing of 3-D/Volumetric Electrical Circuits

    by Gilbert T. Carranza, Ubaldo Robles, Cesar L. Valle, Jesus J. Gutierrez, Raymond C. Rumpf

    For the first time, a fully three-dimensional (3D) electric circuit was modeled in a 3D environment and manufactured via an automated hybrid direct-write 3D printing process. The implications and applications of this significant achievement are enormous because it allows circuits to be designed and manufactured in virtually any form factor. To accomplish this, a custom CAD tool was programmed into an open-source modeling software to layout components and route interconnects. The custom CAD tool imports the netlist and component geometries from a schematic capture program. Components can be placed at any position and be oriented at any angle. Interconnects can meander smoothly throughout the circuit following 3D splines. The interconnects can be placed manually or automatically between components. After laying out the components and routing interconnects, the tool exports Standard Tessellation Language (STL) files of the dielectric and metal portions of the final circuit to be 3D printed. To manufacture the circuit, fused-deposition modeling (FDM) of ABS plastic and micro-dispensing (μD) of DuPont CB028 silver paste were used. To demonstrate, a functional 555 timer circuit was designed and built to flash an LED.