Sofiane Cherif
Research Subjects
Sofiane Cherif has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Hichem Besbes
COSIM Research Lab, Higher School of Communications of Tunis (SUP' COM), University of Carthage, Tunisia
5 shared publications- Imen Nasr
University of Carthage,Department COSIM,Ariana,Tunisia
3 shared publications - Leila Najjar Atallah
Univ Carthage, Ecole Super Commun Tunis SUPCOM, Ariana 2083, Tunisia
3 shared publications - Roberto Lopez-Valcarce
Universidade de Vigo
3 shared publications - Benoit Geller
Department U2IS, ENSTA-ParisTech, 91120 Palaiseau, France
2 shared publications Emna Ben Salem
Research Unit TECHTRA, Sup'Com, University of 7th November at Carthage, Tunisia
2 shared publications
Latest Publications
- 6 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (8) , 7679-7690
Performance Analysis of a Reliable Antenna-Diversity Based Sensing Approach
In wireless communication systems, the correlation among the antennas of diversity systems can hardly be neglected. To the best of our knowledge, no previous studies have attended to address, thoroughly, this problem for the cross-correlation based detectors. This will be the topic of the present paper. Namely, in this paper, we consider the performance assessment of a second order decision metric that is based on the cross-correlation of antenna's output. The detector performance analysis has been made concerning the receiver operating characteristic (ROC) curves, the robustness to estimation uncertainty and the design parameters. This last introduces the minimum required sample number that guarantees a given detection performance. To this end, the probability distribution of the inner product of two complex non-zero-mean partially correlated random vectors is investigated. Next, we exhibited the relevance of our results through the analytical performance derivation of the crosscorrelation assisted sensing approach in terms of design parameters, spectral efficiency, and decision reliability.Monte- Carlo simulations are achieved to prove the tightness of our derived results.
- 6 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 68 (8) , 7679-7690
Performance Analysis of a Reliable Antenna-Diversity Based Sensing Approach
In wireless communication systems, the correlation among the antennas of diversity systems can hardly be neglected. To the best of our knowledge, no previous studies have attended to address, thoroughly, this problem for the cross-correlation based detectors. This will be the topic of the present paper. Namely, in this paper, we consider the performance assessment of a second order decision metric that is based on the cross-correlation of antenna's output. The detector performance analysis has been made concerning the receiver operating characteristic (ROC) curves, the robustness to estimation uncertainty and the design parameters. This last introduces the minimum required sample number that guarantees a given detection performance. To this end, the probability distribution of the inner product of two complex non-zero-mean partially correlated random vectors is investigated. Next, we exhibited the relevance of our results through the analytical performance derivation of the crosscorrelation assisted sensing approach in terms of design parameters, spectral efficiency, and decision reliability.Monte- Carlo simulations are achieved to prove the tightness of our derived results.
- 9 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 17 (1) , 636-651
Near MAP Dynamical Delay Estimator and Bayesian CRB for Coded QAM Signals
This paper presents an off-line algorithm for dynamical time delay recovery for which the whole observation block is used. The time offset varies over the observation interval following a random walk model. The proposed synchronizer applies to data-aided (DA), non-data-aided (NDA) and code-aided (CA) modes. Theoretical performance of the off-line technique is derived and compared to simulation results. The Bayesian Cramer-Rao Bound (BCRB) is also evaluated for DA, NDA and CA modes and for both the off-line and on-line scenarios. Simulation results show the improvement brought by the off-line and the CA schemes. The presented algorithm outperforms the conventional on-line estimator, which only takes into account the current and previous observations, and its MSE approaches the BCRB.
- 9 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 17 (1) , 636-651
Near MAP Dynamical Delay Estimator and Bayesian CRB for Coded QAM Signals
This paper presents an off-line algorithm for dynamical time delay recovery for which the whole observation block is used. The time offset varies over the observation interval following a random walk model. The proposed synchronizer applies to data-aided (DA), non-data-aided (NDA) and code-aided (CA) modes. Theoretical performance of the off-line technique is derived and compared to simulation results. The Bayesian Cramer-Rao Bound (BCRB) is also evaluated for DA, NDA and CA modes and for both the off-line and on-line scenarios. Simulation results show the improvement brought by the off-line and the CA schemes. The presented algorithm outperforms the conventional on-line estimator, which only takes into account the current and previous observations, and its MSE approaches the BCRB.
- 29 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 858-862
A novel optimal Cross-Correlation Combining based sensing approach
Cross-correlation metrics introduce a challenging performance for multiple antennas spectrum sensing in cognitive radio networks, since it permits to alleviate the drawback of the energy based approaches under low SNR and noise level uncertainty, while maintaining the low complexity. In this paper, we propose a novel sensing approach based on a linear soft weighting of the Combined Second Order Moment (CSOM). Two different optimization criteria are developed, namely, the Normal Deflection Criteria (NDC) and the signal to noise power ratio maximization criteria. We demonstrate that both yield to a similar optimum results, given a certain samples number, thus, same philosophy in decision of the band occupancy. Simulation results show decision accuracy improvement compared to the existing approaches as the BCED, MME and SLC based energy detector. In fact, the proposed sensing strategy guarantees minimal interference to the primary user (high detection probability) while maintaining a good amount of spectral efficiency (low false alarm).
- 29 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 858-862
A novel optimal Cross-Correlation Combining based sensing approach
Cross-correlation metrics introduce a challenging performance for multiple antennas spectrum sensing in cognitive radio networks, since it permits to alleviate the drawback of the energy based approaches under low SNR and noise level uncertainty, while maintaining the low complexity. In this paper, we propose a novel sensing approach based on a linear soft weighting of the Combined Second Order Moment (CSOM). Two different optimization criteria are developed, namely, the Normal Deflection Criteria (NDC) and the signal to noise power ratio maximization criteria. We demonstrate that both yield to a similar optimum results, given a certain samples number, thus, same philosophy in decision of the band occupancy. Simulation results show decision accuracy improvement compared to the existing approaches as the BCED, MME and SLC based energy detector. In fact, the proposed sensing strategy guarantees minimal interference to the primary user (high detection probability) while maintaining a good amount of spectral efficiency (low false alarm).
- 29 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 417-421
Power control and RB allocation for LTE uplink
According to 3GPP standards, the Single Carrier Frequency Division Multiple Access (SC-FDMA) was adopted for Uplink transmission in LTE networks. As multiple mobiles may have access to neighboring base stations simultaneously, the inter-cell interferences are inevitable with this technique and the system throughput is impacted. To mitigate the inter-cell interference and improve, therefore, the system performance, severe schemes have been proposed. However, these schemes target either adapting the power control in mobile stations (e.g. Fractional Power Control technique) or improving the Resource Block (RB) allocation (e.g. Universal Frequency Reuse technique). In this paper, we propose two new techniques to reduce the inter-cell interferences namely: (i) Dynamic Fractional Power Control and (ii) a Resource Block Allocation based on Genetic Algorithm. In addition, we advocate that, by combining these technique, the system can achieve a better throughput.
- 29 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 417-421
Power control and RB allocation for LTE uplink
According to 3GPP standards, the Single Carrier Frequency Division Multiple Access (SC-FDMA) was adopted for Uplink transmission in LTE networks. As multiple mobiles may have access to neighboring base stations simultaneously, the inter-cell interferences are inevitable with this technique and the system throughput is impacted. To mitigate the inter-cell interference and improve, therefore, the system performance, severe schemes have been proposed. However, these schemes target either adapting the power control in mobile stations (e.g. Fractional Power Control technique) or improving the Resource Block (RB) allocation (e.g. Universal Frequency Reuse technique). In this paper, we propose two new techniques to reduce the inter-cell interferences namely: (i) Dynamic Fractional Power Control and (ii) a Resource Block Allocation based on Genetic Algorithm. In addition, we advocate that, by combining these technique, the system can achieve a better throughput.
- 29 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 779-783
Linear Prediction for data compression and recovery enhancement in Wireless Sensors Networks
Compressed Sensing (CS) has been successfully applied within Wireless Sensors Networks (WSN). We consider the problem of data recovery from a subset of few sensor readings collection at a fusion center in the case of spatially correlated large WSN. We exploit the data spatial correlation to derive a sparse representation of the signal and consider 1-D reading of the WSN. To this end, we propose a novel approach based on Linear Prediction Coding (LPC) as a sparsifying transform. Then, the Orthogonal Matching Pursuit (OMP) CS algorithm is used for original data recovery. We adopt a uniform spatial correlation model which induces a problem with an unknown degree of sparsity. In this scenario, the OMP operates with a stopping rule conditioned by the residual observation norm. Our approach outperforms other 1-D conventional sparsity-inducing methods such as DCT, PCA and DFT across a wide range of spatial correlation levels. The obtained enhancement is especially obtained for low number of measurements, thus leading to a significant power consumption reduction.
- 29 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 779-783
Linear Prediction for data compression and recovery enhancement in Wireless Sensors Networks
Compressed Sensing (CS) has been successfully applied within Wireless Sensors Networks (WSN). We consider the problem of data recovery from a subset of few sensor readings collection at a fusion center in the case of spatially correlated large WSN. We exploit the data spatial correlation to derive a sparse representation of the signal and consider 1-D reading of the WSN. To this end, we propose a novel approach based on Linear Prediction Coding (LPC) as a sparsifying transform. Then, the Orthogonal Matching Pursuit (OMP) CS algorithm is used for original data recovery. We adopt a uniform spatial correlation model which induces a problem with an unknown degree of sparsity. In this scenario, the OMP operates with a stopping rule conditioned by the residual observation norm. Our approach outperforms other 1-D conventional sparsity-inducing methods such as DCT, PCA and DFT across a wide range of spatial correlation levels. The obtained enhancement is especially obtained for low number of measurements, thus leading to a significant power consumption reduction.
- 12 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal Processing
- Vol. 64 (3) , 799-811
Performance Study of a Near Maximum Likelihood Code-Aided Timing Recovery Technique
In this paper, we propose a new code-aided (CA) timing recovery algorithm for various linear constant modulus constellations based on the Maximum Likelihood (ML) estimator. The first contribution is the derivation of a soft estimator expression of the transmitted symbol instead of its true or hard estimated value which is fed into the timing error detector (TED) equation. The proposed expression includes the Log-Likelihood Ratios (LLRs) obtained from a turbo decoder. Our results show that the proposed CA approach achieves almost as good results as the data-aided (DA) approach over a large interval of SNR values while achieving a higher spectral efficiency. We also derive the corresponding CA Cramer Rao Bounds (CRB) for various modulation orders. Contrarily to former work, we develop here the CRB analytical expression for different M-PSK modulation orders and validate them through comparison to empirical CRB obtained by Monte Carlo iterations. The proposed CA estimator realizes an important gain over the nondata-aided approach (NDA) and achieves a smaller gap when compared to its relative CA CRB, especially at moderate SNR values where modern systems are constrained to work.
- 12 October 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal Processing
- Vol. 64 (3) , 799-811
Performance Study of a Near Maximum Likelihood Code-Aided Timing Recovery Technique
In this paper, we propose a new code-aided (CA) timing recovery algorithm for various linear constant modulus constellations based on the Maximum Likelihood (ML) estimator. The first contribution is the derivation of a soft estimator expression of the transmitted symbol instead of its true or hard estimated value which is fed into the timing error detector (TED) equation. The proposed expression includes the Log-Likelihood Ratios (LLRs) obtained from a turbo decoder. Our results show that the proposed CA approach achieves almost as good results as the data-aided (DA) approach over a large interval of SNR values while achieving a higher spectral efficiency. We also derive the corresponding CA Cramer Rao Bounds (CRB) for various modulation orders. Contrarily to former work, we develop here the CRB analytical expression for different M-PSK modulation orders and validate them through comparison to empirical CRB obtained by Monte Carlo iterations. The proposed CA estimator realizes an important gain over the nondata-aided approach (NDA) and achieves a smaller gap when compared to its relative CA CRB, especially at moderate SNR values where modern systems are constrained to work.
- 10 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in China Communications
- Vol. 12 (2) , 1-10
On a hybrid preamble/soft-output demapper approach for time synchronization for IEEE 802.15.6 narrowband WBAN
In this paper, we present a maximum likelihood (ML) based time synchronization algorithm for Wireless Body Area Networks (WBAN). The proposed technique takes advantage of soft information retrieved from the soft demapper for the time delay estimation. This algorithm has a low complexity and is adapted to the frame structure specified by the IEEE 802.15.6 standard for the narrowband systems. Simulation results have shown good performance which approach the theoretical mean square error limit bound represented by the Cramer Rao Bound (CRB).
- 10 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in China Communications
- Vol. 12 (2) , 1-10
On a hybrid preamble/soft-output demapper approach for time synchronization for IEEE 802.15.6 narrowband WBAN
In this paper, we present a maximum likelihood (ML) based time synchronization algorithm for Wireless Body Area Networks (WBAN). The proposed technique takes advantage of soft information retrieved from the soft demapper for the time delay estimation. This algorithm has a low complexity and is adapted to the frame structure specified by the IEEE 802.15.6 standard for the narrowband systems. Simulation results have shown good performance which approach the theoretical mean square error limit bound represented by the Cramer Rao Bound (CRB).
- Open Access
- 1 January 2013
- Published by Wiley in The Scientific World Journal
- Vol. 2013 (1) , 437926
QoS and Energy Aware Cooperative Routing Protocol for Wildfire Monitoring Wireless Sensor Networks
Wireless sensor networks (WSN) are presented as proper solution for wildfire monitoring. However, this application requires a design of WSN taking into account the network lifetime and the shadowing effect generated by the trees in the forest environment. Cooperative communication is a promising solution for WSN which uses, at each hop, the resources of multiple nodes to transmit its data. Thus, by sharing resources between nodes, the transmission quality is enhanced. In this paper, we use the technique of reinforcement learning by opponent modeling, optimizing a cooperative communication protocol based on RSSI and node energy consumption in a competitive context (RSSI/energy‐CC), that is, an energy and quality‐of‐service aware‐based cooperative communication routing protocol. Simulation results show that the proposed algorithm performs well in terms of network lifetime, packet delay, and energy consumption.
- 1 January 2013
- Published by Wiley in The Scientific World Journal
- Vol. 2013 (1) , 437926
Open AccessQoS and Energy Aware Cooperative Routing Protocol for Wildfire Monitoring Wireless Sensor Networks
Wireless sensor networks (WSN) are presented as proper solution for wildfire monitoring. However, this application requires a design of WSN taking into account the network lifetime and the shadowing effect generated by the trees in the forest environment. Cooperative communication is a promising solution for WSN which uses, at each hop, the resources of multiple nodes to transmit its data. Thus, by sharing resources between nodes, the transmission quality is enhanced. In this paper, we use the technique of reinforcement learning by opponent modeling, optimizing a cooperative communication protocol based on RSSI and node energy consumption in a competitive context (RSSI/energy‐CC), that is, an energy and quality‐of‐service aware‐based cooperative communication routing protocol. Simulation results show that the proposed algorithm performs well in terms of network lifetime, packet delay, and energy consumption.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21669570,p. 1606-1610
Dynamic fractional power control for LTE uplink
Recently, the 3rd Generation Partnership Project has standardized a power control mechanism for the uplink of the Long Term Evolution system. This mechanism is based on the fractional compensation of the pathloss, also known as fractional power control. This approach decreases inter-cell interference but may impact the throughput. In this paper, a novel approach power control will be proposed to avoid such throughput loss. This method still uses fractional power control principle, but differentiates between users generating high interference and users generating low interference. Our simulations indicate that the proposed power control has better performance than the fractional power control.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21669570,p. 1606-1610
Dynamic fractional power control for LTE uplink
Recently, the 3rd Generation Partnership Project has standardized a power control mechanism for the uplink of the Long Term Evolution system. This mechanism is based on the fractional compensation of the pathloss, also known as fractional power control. This approach decreases inter-cell interference but may impact the throughput. In this paper, a novel approach power control will be proposed to avoid such throughput loss. This method still uses fractional power control principle, but differentiates between users generating high interference and users generating low interference. Our simulations indicate that the proposed power control has better performance than the fractional power control.
- 1 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Multicarrier equalization by subchannel SINR maximization
In multicarrier (MC) communication receivers, the use of a time-domain equalizer (TEQ) mitigates inter-symbol and inter-carrier interferences by shortening the overall channel delay spread. Nevertheless, the TEQ-based MC-receiver structure does not result in optimal bit rate and if one wants to optimize the bit rate a nonlinear cost function has to be maximized. Hence, to optimize the MC system bit rate, we aim to equalize each subchannel separately by maximizing its Signal-to-Interference and Noise Ratio (SINR). The proposed approach is based on exact and accurate model of the subchannel SINR. Optimal equalizers are then designed in the case of ADSL environment where numerical simulation confirms the improvement in performance of the proposed approach with respect to previous methods.
- 1 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Multicarrier equalization by subchannel SINR maximization
In multicarrier (MC) communication receivers, the use of a time-domain equalizer (TEQ) mitigates inter-symbol and inter-carrier interferences by shortening the overall channel delay spread. Nevertheless, the TEQ-based MC-receiver structure does not result in optimal bit rate and if one wants to optimize the bit rate a nonlinear cost function has to be maximized. Hence, to optimize the MC system bit rate, we aim to equalize each subchannel separately by maximizing its Signal-to-Interference and Noise Ratio (SINR). The proposed approach is based on exact and accurate model of the subchannel SINR. Optimal equalizers are then designed in the case of ADSL environment where numerical simulation confirms the improvement in performance of the proposed approach with respect to previous methods.