Saroj Kumar Sahoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Saroj Kumar Sahoo has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Nikkam Suresh
Department of Fuel and Mineral Engineering, Indian Institute of Technology (Indian School of Mines), Dhanbad, India
9 shared publicationsAtul Kumar Varma
Department of Applied Geology, Indian School of Mines, Dhanbad, India
7 shared publicationsA. K. Varma
Department of Applied Geology, Indian School of Mines, Dhanbad, India
1 shared publication
Latest Publications
- 19 May 2018
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (10) , 1250-1256
Recovery of coal values from the refuse pond coal slurry using flotation
The objective of the present investigation is to explore the possibility of recovery of coal values from the tailing dump, so as to recover the coal values from the discarded product for sustainable development and optimum utilization of coal reserves. The influence of two important variables which commonly fluctuate in the operating plants, such as feed solid concentrations and collector dosage, has been varied and analyzed to study their influence on flotation performance. Among the variables studied, the pulp density of 8% of feed solid concentration was found to be most suitable level. A collector dosage of 0.105 kg/ton of coal gave the best result in term of ash reduction.
- 19 May 2018
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 40 (10) , 1250-1256
Recovery of coal values from the refuse pond coal slurry using flotation
The objective of the present investigation is to explore the possibility of recovery of coal values from the tailing dump, so as to recover the coal values from the discarded product for sustainable development and optimum utilization of coal reserves. The influence of two important variables which commonly fluctuate in the operating plants, such as feed solid concentrations and collector dosage, has been varied and analyzed to study their influence on flotation performance. Among the variables studied, the pulp density of 8% of feed solid concentration was found to be most suitable level. A collector dosage of 0.105 kg/ton of coal gave the best result in term of ash reduction.
- 4 March 2018
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 41 (3) , 159-176
Performance Evaluation of Batch Coal Flotation from the Petrologic Point of View
In this paper, an attempt was made to study the flotability of washery grade-IV (ash content between 28% and 35%) type of coking coal in terms of maceral components and to examine how each maceral group floats in the course of a time-wise batch flotation test. The objective of this paper was to evaluate the flotation characteristics of high-ash coking coal fines (of size <500 µm) in terms of the maceral components using different levels of collector (diesel oil) and frother (methyl isobutyl carbinol). The flotation test results were evaluated from the petrologic analysis, and the petrographic test results show that at equal level of collector and frother doses (0.5 kg/ton), 86% of the vitrinite maceral group floated into the concentrate in 120 s, and 77% of the mineral matter and 90% of pyrite were observed in the last two concentrates and flotation tailings. Proportionate distribution of the maceral components in flotation products was confirmed through the petrographic analysis. The different flotability of coal petrographic constituents was further investigated through surface characterization techniques such as contact angle, zeta potential, and Fourier transform-infrared spectroscopy.
- 4 March 2018
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 41 (3) , 159-176
Performance Evaluation of Batch Coal Flotation from the Petrologic Point of View
In this paper, an attempt was made to study the flotability of washery grade-IV (ash content between 28% and 35%) type of coking coal in terms of maceral components and to examine how each maceral group floats in the course of a time-wise batch flotation test. The objective of this paper was to evaluate the flotation characteristics of high-ash coking coal fines (of size <500 µm) in terms of the maceral components using different levels of collector (diesel oil) and frother (methyl isobutyl carbinol). The flotation test results were evaluated from the petrologic analysis, and the petrographic test results show that at equal level of collector and frother doses (0.5 kg/ton), 86% of the vitrinite maceral group floated into the concentrate in 120 s, and 77% of the mineral matter and 90% of pyrite were observed in the last two concentrates and flotation tailings. Proportionate distribution of the maceral components in flotation products was confirmed through the petrographic analysis. The different flotability of coal petrographic constituents was further investigated through surface characterization techniques such as contact angle, zeta potential, and Fourier transform-infrared spectroscopy.
- 19 December 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 40 (11) , 755-765
Determining the Best Particle Size-Class for Flotation of a High Ash Coal
The purpose of this study was to investigate the effect of particle size on coal flotation in terms of kinetic parameters such as flotation rate constant and maximum recovery. Six different flotation kinetic models were applied to data from tests using the MATLAB statistical analysis tool package to estimate the relationship between the flotation rate constant, the maximum combustible value recovery, and the particle size. Within the size range studied, the best flotation performance was obtained at −75 + 25 µ size fractions. The result shows that all kinetic models except the second-order model with rectangular distribution of flotabilities gave an excellent fit to the experimental data at various size fractions. From the statistical analysis, we conclude that coal flotation with combustible matter recovery as the response can be described with the first-order model with rectangular distribution of flotabilities, .
- 19 December 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 40 (11) , 755-765
Determining the Best Particle Size-Class for Flotation of a High Ash Coal
The purpose of this study was to investigate the effect of particle size on coal flotation in terms of kinetic parameters such as flotation rate constant and maximum recovery. Six different flotation kinetic models were applied to data from tests using the MATLAB statistical analysis tool package to estimate the relationship between the flotation rate constant, the maximum combustible value recovery, and the particle size. Within the size range studied, the best flotation performance was obtained at −75 + 25 µ size fractions. The result shows that all kinetic models except the second-order model with rectangular distribution of flotabilities gave an excellent fit to the experimental data at various size fractions. From the statistical analysis, we conclude that coal flotation with combustible matter recovery as the response can be described with the first-order model with rectangular distribution of flotabilities, .
- 5 September 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 40 (3) , 155-174
Flotation production of vitrinite maceral concentrate and its optimization using response surface approach
- 5 September 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 40 (3) , 155-174
Flotation production of vitrinite maceral concentrate and its optimization using response surface approach
- Open Access
- 6 June 2017
- Published by Science Publishing Group in Journal of Energy and Natural Resources
- Vol. 6 (3) , 38-44
Studies on Separation of Macerals from Coal by Froth Flotation
In the past coal maceral separation have been carried out based on density difference e. g., sink-float analysis, density gradient centrifugation (DGC) techniques etc. These approaches are of limited success. Froth flotation is a physico-chemical process separating particles on the basis of difference in surface properties in a vessel consisting of two distinct zones viz., pulp and froth zones. Rate of floatability of individual size range particles varies with their ash percent and the maceral content present. Therefore, the flotation rate constant eventually becomes a function of maceral percentage of a coal particle. In the present paper, an attempt has been made by performing size-wise flotation tests using a sub-bituminous rank coal and flotation kinetics have been established based on maceral percentage reporting to concentrate at different time intervals of flotation. These results have been related to the kinetic behaviour of the process.
- 6 June 2017
- Published by Science Publishing Group in Journal of Energy and Natural Resources
- Vol. 6 (3) , 38-44
Open AccessStudies on Separation of Macerals from Coal by Froth Flotation
In the past coal maceral separation have been carried out based on density difference e. g., sink-float analysis, density gradient centrifugation (DGC) techniques etc. These approaches are of limited success. Froth flotation is a physico-chemical process separating particles on the basis of difference in surface properties in a vessel consisting of two distinct zones viz., pulp and froth zones. Rate of floatability of individual size range particles varies with their ash percent and the maceral content present. Therefore, the flotation rate constant eventually becomes a function of maceral percentage of a coal particle. In the present paper, an attempt has been made by performing size-wise flotation tests using a sub-bituminous rank coal and flotation kinetics have been established based on maceral percentage reporting to concentrate at different time intervals of flotation. These results have been related to the kinetic behaviour of the process.
- 5 May 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 39 (5) , 259-280
Kinetic Studies on Petrographic Components of Coal in Batch Flotation Operation
In the present paper, an attempt was made to study the kinetic behavior of different types of maceral during flotation of a washery grade-IV type of coking coal. Three important operational variables, viz. collector dose (kg/ton), frother dose (kg/ton), and feed solid concentrations (%), were varied, and their effects on the response parameters like recoveries of ash and petrographic components, viz. vitrinite (V), liptinite (L), and inertinite (I), were evaluated. A first-order flotation kinetic equation was fitted for the batch test data for evaluating the rate of flotation (k) of coal components. Use of a three-level Box-Behnken factorial design was adopted to minimize the number of experiments and modeling of response parameters in batch coal flotation. The obtained results were evaluated with quadratic programming to develop second-order regression equations. For understanding of the influence of interactional effects, response surface methodology (RSM) approach was adopted. Taking advantages of the quadratic programming, it was observed that recovery of 100% vitrinite was obtained without collector, however, with frother dosage and feed solid concentration of 0.75kg/ton and 5%, respectively. Similarly, minimum ultimate recovery of ash and inertinite component was achieved at intermediate range of reagent dosages and pulp density (collector ≡ 0.40–0.45kg/ton, frother ≡ 0.40–0.45kg/ton, and feed solid concentration of 9–10%). The influence of these process variables of the batch coal flotation on ultimate recovery (R∞) and rate constant (k) values of maceral components are discussed critically in this paper.
- 5 May 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 39 (5) , 259-280
Kinetic Studies on Petrographic Components of Coal in Batch Flotation Operation
In the present paper, an attempt was made to study the kinetic behavior of different types of maceral during flotation of a washery grade-IV type of coking coal. Three important operational variables, viz. collector dose (kg/ton), frother dose (kg/ton), and feed solid concentrations (%), were varied, and their effects on the response parameters like recoveries of ash and petrographic components, viz. vitrinite (V), liptinite (L), and inertinite (I), were evaluated. A first-order flotation kinetic equation was fitted for the batch test data for evaluating the rate of flotation (k) of coal components. Use of a three-level Box-Behnken factorial design was adopted to minimize the number of experiments and modeling of response parameters in batch coal flotation. The obtained results were evaluated with quadratic programming to develop second-order regression equations. For understanding of the influence of interactional effects, response surface methodology (RSM) approach was adopted. Taking advantages of the quadratic programming, it was observed that recovery of 100% vitrinite was obtained without collector, however, with frother dosage and feed solid concentration of 0.75kg/ton and 5%, respectively. Similarly, minimum ultimate recovery of ash and inertinite component was achieved at intermediate range of reagent dosages and pulp density (collector ≡ 0.40–0.45kg/ton, frother ≡ 0.40–0.45kg/ton, and feed solid concentration of 9–10%). The influence of these process variables of the batch coal flotation on ultimate recovery (R∞) and rate constant (k) values of maceral components are discussed critically in this paper.
- 10 April 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 39 (2) , 65-87
Performance Evaluation of Basic Flotation Kinetic Models Using Advanced Statistical Techniques
- 10 April 2017
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 39 (2) , 65-87
Performance Evaluation of Basic Flotation Kinetic Models Using Advanced Statistical Techniques
- 29 March 2017
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 39 (10) , 992-998
Characterization of macerals from the coal flotation froth fraction
Coal samples composed of vitrinite, liptinite, and inertinite are characterized by KBr-FTIR spectroscopy. It exhibits the highest aromaticity (ratio of CHar at 3,000–3,100 cm−1 or 700–900 cm−1 versus CHal at 2,800–3,000 cm−1), reflecting the lowest hydrocarbon generating potential in the first froth fraction compared to all the other fractions. The ratio of CHal/(CHal +C=C) (i.e. A factor), which reflects the hydrocarbon-generating potential, is the lowest for the first concentrate. Variations of semiquantitative ratios differ less significantly between 15 s and 90 s. However, large difference of aromaticity is found between feed coal and the first concentrate. The DOC value is slightly higher for the first concentrate than the feed fractions.
- 29 March 2017
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 39 (10) , 992-998
Characterization of macerals from the coal flotation froth fraction
Coal samples composed of vitrinite, liptinite, and inertinite are characterized by KBr-FTIR spectroscopy. It exhibits the highest aromaticity (ratio of CHar at 3,000–3,100 cm−1 or 700–900 cm−1 versus CHal at 2,800–3,000 cm−1), reflecting the lowest hydrocarbon generating potential in the first froth fraction compared to all the other fractions. The ratio of CHal/(CHal +C=C) (i.e. A factor), which reflects the hydrocarbon-generating potential, is the lowest for the first concentrate. Variations of semiquantitative ratios differ less significantly between 15 s and 90 s. However, large difference of aromaticity is found between feed coal and the first concentrate. The DOC value is slightly higher for the first concentrate than the feed fractions.
- Retracted
- 22 March 2017
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 39 (9) , 893-898
RETRACTION ARTICLE: Correlation between Average Gray Value (AGV) of coal froth image with its ash and vitrinite content
In this study, an attempt is made for the offline prediction of ash and the vitrinite content of froth fraction using the image analysis technique. Average Gray Value (AGV) was used as the key parameter in this study. Time-wise froth images were captured during the experiment and processed in a computer, embedded with Matlab 7.0 software. A good correlation was obtained between AGV and ash content (R2 ≡ 0.8309) and also with vitrinite maceral content in concentrate (R2 ≡ 0.7166). Low gray value indicates dark froth with a low ash content of coal particles with high vitrinite maceral content, whereas high gray value represents bright froth with more water and high ash clay minerals in the froth.
- 22 March 2017
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 39 (9) , 893-898
RetractedRETRACTION ARTICLE: Correlation between Average Gray Value (AGV) of coal froth image with its ash and vitrinite content
In this study, an attempt is made for the offline prediction of ash and the vitrinite content of froth fraction using the image analysis technique. Average Gray Value (AGV) was used as the key parameter in this study. Time-wise froth images were captured during the experiment and processed in a computer, embedded with Matlab 7.0 software. A good correlation was obtained between AGV and ash content (R2 ≡ 0.8309) and also with vitrinite maceral content in concentrate (R2 ≡ 0.7166). Low gray value indicates dark froth with a low ash content of coal particles with high vitrinite maceral content, whereas high gray value represents bright froth with more water and high ash clay minerals in the froth.