Nan Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nan Xu has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
Qining Song
Hohai University
18 shared publicationsYefeng Bao
College of Materials Science and Engineering, Hohai University, Changzhou, China
15 shared publicationsDan Wang
8 shared publicationsJun Shen
7 shared publicationsJianhua Zhao
College of Materials Science and Engineering, Hohai University, Changzhou, China
5 shared publicationsQi-Ning Song
College of Materials Science and Engineering, Hohai University, Changzhou, China
5 shared publications
Latest Publications
- Open Access
- 12 September 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of laser power and Ti foil interlayer thickness on porosity and tensile behavior of laser-welded B 4 C/6061Al composites
Laser welding of 30 vol.% B4C/6061Al aluminum matrix composites fabricated by powder metallurgy and rolling was investigated, with particular emphasis on porosity evolution and the effect of Ti foil interlayers on joint performance. The porosity first decreased and then increased with increasing laser power, and relatively low porosity was achieved in the range of 1.8–2.0 kW. Under the Ti-free condition, the maximum joint tensile strength reached about 102 MPa at 1.8 kW. Needle-like Al4C3 phases were formed at the particle edges after welding. To further improve joint properties, Ti foils with thicknesses of 0.01-0.15 mm were introduced at 2.0 kW. The addition of Ti refined the particle distribution and modified the interfacial reaction path. Al3Ti and TiB2 phases were observed in the weld, and TEM analysis confirmed the coexistence of TiB2 and Al4C4Bx in the reaction region, indicating a partial suppression of Al4C3 formation. The joint strength first increased and then decreased with increasing Ti foil thickness, reaching a maximum of 118.48 MPa at 0.10 mm Ti foil. This optimal condition corresponded to relatively low porosity and a more uniform weld microstructure. However, excessive Ti addition would lead to elemental segregation, deteriorated homogenization, and incomplete penetration.
- 12 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of laser power and Ti foil interlayer thickness on porosity and tensile behavior of laser-welded B 4 C/6061Al composites
Laser welding of 30 vol.% B4C/6061Al aluminum matrix composites fabricated by powder metallurgy and rolling was investigated, with particular emphasis on porosity evolution and the effect of Ti foil interlayers on joint performance. The porosity first decreased and then increased with increasing laser power, and relatively low porosity was achieved in the range of 1.8–2.0 kW. Under the Ti-free condition, the maximum joint tensile strength reached about 102 MPa at 1.8 kW. Needle-like Al4C3 phases were formed at the particle edges after welding. To further improve joint properties, Ti foils with thicknesses of 0.01-0.15 mm were introduced at 2.0 kW. The addition of Ti refined the particle distribution and modified the interfacial reaction path. Al3Ti and TiB2 phases were observed in the weld, and TEM analysis confirmed the coexistence of TiB2 and Al4C4Bx in the reaction region, indicating a partial suppression of Al4C3 formation. The joint strength first increased and then decreased with increasing Ti foil thickness, reaching a maximum of 118.48 MPa at 0.10 mm Ti foil. This optimal condition corresponded to relatively low porosity and a more uniform weld microstructure. However, excessive Ti addition would lead to elemental segregation, deteriorated homogenization, and incomplete penetration.
- 27 July 2026
- Published by SAGE Publications in Materials Science and Technology
Microstructural and mechanical properties of multi-pass rapid cooling friction-stir welded A1050 aluminum alloy
Conventional multi-pass friction stir welding (FSW) often causes thermal softening in pure aluminum joints. This leads to grain coarsening and a marked reduction in dislocation density, limiting the simultaneous achievement of grain refinement and work hardening. To address this issue, a multi-pass rapid cooling friction-stir welding (MPRC-FSW) process was developed using liquid CO 2 as a cooling medium. The objective was to achieve cumulative grain refinement while preserving deformation-induced substructures. 2-mm-thick A1050 pure aluminum plates were welded with up to five overlapping passes under same welding conditions. This approach progressively refines the grain structure while retaining a high dislocation density. After five passes, the average grain size in the stir zone (SZ) decreases from 2.7 μm (1 pass) to 1.3 μm. The kernel average misorientation value, which reflects dislocation density, increases from 0.07° to 0.31°. Microstructural evolution follows a two-stage mechanism. The initial stage is dominated by continuous dynamic recrystallization which refines grains and increases the fraction of high-angle grain boundaries. In the subsequent stage, further passes introduce new dislocation substructures within the ultrafine grains. The yield strength of the SZ reaches 88 MPa, comparable to that of the base material (91 MPa), while elongation exceeds that of the base material, demonstrating improved strength-ductility synergy. This hybrid process effectively overcomes thermal softening in conventional multi-pass FSW by enabling cumulative grain refinement and sustained dislocation strengthening.
- 27 July 2026
- Published by SAGE Publications in Materials Science and Technology
Microstructural and mechanical properties of multi-pass rapid cooling friction-stir welded A1050 aluminum alloy
Conventional multi-pass friction stir welding (FSW) often causes thermal softening in pure aluminum joints. This leads to grain coarsening and a marked reduction in dislocation density, limiting the simultaneous achievement of grain refinement and work hardening. To address this issue, a multi-pass rapid cooling friction-stir welding (MPRC-FSW) process was developed using liquid CO 2 as a cooling medium. The objective was to achieve cumulative grain refinement while preserving deformation-induced substructures. 2-mm-thick A1050 pure aluminum plates were welded with up to five overlapping passes under same welding conditions. This approach progressively refines the grain structure while retaining a high dislocation density. After five passes, the average grain size in the stir zone (SZ) decreases from 2.7 μm (1 pass) to 1.3 μm. The kernel average misorientation value, which reflects dislocation density, increases from 0.07° to 0.31°. Microstructural evolution follows a two-stage mechanism. The initial stage is dominated by continuous dynamic recrystallization which refines grains and increases the fraction of high-angle grain boundaries. In the subsequent stage, further passes introduce new dislocation substructures within the ultrafine grains. The yield strength of the SZ reaches 88 MPa, comparable to that of the base material (91 MPa), while elongation exceeds that of the base material, demonstrating improved strength-ductility synergy. This hybrid process effectively overcomes thermal softening in conventional multi-pass FSW by enabling cumulative grain refinement and sustained dislocation strengthening.
- Open Access
- 5 June 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of laser power and Ti foil interlayer thickness on porosity and tensile behavior of laser-welded B4C/6061Al composites
Laser welding of 30 vol.% B4C/6061Al aluminum matrix composites fabricated by powder metallurgy and rolling was investigated, with particular emphasis on porosity evolution and the effect of Ti foil interlayers on joint performance. Full-penetration joints were obtained at laser powers from 1.1 to 2.3 kW. The porosity first decreased and then increased with increasing laser power, and relatively low porosity was achieved in the range of 1.8–2.0 kW. Under the Ti-free condition, the maximum joint tensile strength reached about 102 MPa at 1.8 kW. Microstructural observations showed that B4C particles in the weld exhibited edge segregation, central agglomeration, and root depletion, which were governed by molten-pool convection and solidification-interface effects. Needle-like Al4C3 phases were formed at the particle edges after welding. To further improve joint properties, Ti foils with thicknesses of 0.01-0.15 mm were introduced at 2.0 kW. The addition of Ti refined the particle distribution and modified the interfacial reaction path. Al3Ti and TiB2 phases were observed in the weld, and TEM analysis confirmed the coexistence of TiB2 and Al4C4Bx in the reaction region, indicating a partial suppression of Al4C3 formation. The joint strength first increased and then decreased with increasing Ti foil thickness, reaching a maximum of 118.48 MPa at 0.10 mm Ti foil. This optimal condition corresponded to relatively low porosity and a more uniform weld microstructure. Excessive Ti addition, however, led to elemental segregation, deteriorated homogenization, and incomplete penetration. These results demonstrate that an appropriate Ti foil interlayer can effectively optimize the microstructure and improve the tensile properties of laser-welded B4C/6061Al joints.
- 5 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of laser power and Ti foil interlayer thickness on porosity and tensile behavior of laser-welded B4C/6061Al composites
Laser welding of 30 vol.% B4C/6061Al aluminum matrix composites fabricated by powder metallurgy and rolling was investigated, with particular emphasis on porosity evolution and the effect of Ti foil interlayers on joint performance. Full-penetration joints were obtained at laser powers from 1.1 to 2.3 kW. The porosity first decreased and then increased with increasing laser power, and relatively low porosity was achieved in the range of 1.8–2.0 kW. Under the Ti-free condition, the maximum joint tensile strength reached about 102 MPa at 1.8 kW. Microstructural observations showed that B4C particles in the weld exhibited edge segregation, central agglomeration, and root depletion, which were governed by molten-pool convection and solidification-interface effects. Needle-like Al4C3 phases were formed at the particle edges after welding. To further improve joint properties, Ti foils with thicknesses of 0.01-0.15 mm were introduced at 2.0 kW. The addition of Ti refined the particle distribution and modified the interfacial reaction path. Al3Ti and TiB2 phases were observed in the weld, and TEM analysis confirmed the coexistence of TiB2 and Al4C4Bx in the reaction region, indicating a partial suppression of Al4C3 formation. The joint strength first increased and then decreased with increasing Ti foil thickness, reaching a maximum of 118.48 MPa at 0.10 mm Ti foil. This optimal condition corresponded to relatively low porosity and a more uniform weld microstructure. Excessive Ti addition, however, led to elemental segregation, deteriorated homogenization, and incomplete penetration. These results demonstrate that an appropriate Ti foil interlayer can effectively optimize the microstructure and improve the tensile properties of laser-welded B4C/6061Al joints.
- Open Access
The Effect of Ultrasonic Vibration Assistance During Laser Lap Welding on the Microstructure and Properties of Galvanized Steel/Mg Joints
In this work, a laser lap-welded joint of galvanized steel/Mg and a laser lap-welded joint of galvanized steel/Mg assisted by ultrasonic vibration were compared. By adjusting the laser beam power and ultrasonic amplitude, the appropriate welding process parameters were obtained. The weld formation, microstructure and mechanical properties were studied and analyzed. The results indicated that the addition of ultrasonic vibration generated an excitation force with a certain frequency and amplitude on the weldment, making the molten metal in the molten pool produce ultrasonic forced vibration, and producing the effects of cavitation, acoustic streaming, mechanical stirring and heat, thus reducing welding residual stress and welding-deformation, porosity and incomplete-fusion defects. In addition, it can make the fusion zone transition evenly, improve the wettability, refine the weld grain, and reduce the average grain area from 583 μm2 to 324 μm2. Moreover, the distribution of Mg-Zn reinforcing phase at the interface was more uniform and denser, and the maximum tensile shear strength increased from 179.9 N/mm to 290 N/mm, indicating that the addition of ultrasonic vibration was conducive to improving the comprehensive mechanical properties of the joint.
Open AccessThe Effect of Ultrasonic Vibration Assistance During Laser Lap Welding on the Microstructure and Properties of Galvanized Steel/Mg Joints
In this work, a laser lap-welded joint of galvanized steel/Mg and a laser lap-welded joint of galvanized steel/Mg assisted by ultrasonic vibration were compared. By adjusting the laser beam power and ultrasonic amplitude, the appropriate welding process parameters were obtained. The weld formation, microstructure and mechanical properties were studied and analyzed. The results indicated that the addition of ultrasonic vibration generated an excitation force with a certain frequency and amplitude on the weldment, making the molten metal in the molten pool produce ultrasonic forced vibration, and producing the effects of cavitation, acoustic streaming, mechanical stirring and heat, thus reducing welding residual stress and welding-deformation, porosity and incomplete-fusion defects. In addition, it can make the fusion zone transition evenly, improve the wettability, refine the weld grain, and reduce the average grain area from 583 μm2 to 324 μm2. Moreover, the distribution of Mg-Zn reinforcing phase at the interface was more uniform and denser, and the maximum tensile shear strength increased from 179.9 N/mm to 290 N/mm, indicating that the addition of ultrasonic vibration was conducive to improving the comprehensive mechanical properties of the joint.
- 24 October 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (12) , 11996-12005
Investigation on Different Microstructural and Strengthening Mechanisms of Dissimilar Copper and Brass Joint Using Cold Source-Assisted Friction Stir Welding
- 24 October 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (12) , 11996-12005
Investigation on Different Microstructural and Strengthening Mechanisms of Dissimilar Copper and Brass Joint Using Cold Source-Assisted Friction Stir Welding
- 30 October 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (15) , 15823-15830
The Influence of Thermal Cycle on the Grain Structure of Friction-Stir-Welded Pure Copper Joint
- 30 October 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (15) , 15823-15830
The Influence of Thermal Cycle on the Grain Structure of Friction-Stir-Welded Pure Copper Joint
- Open Access
- 28 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 1553-1571
Enhanced mechanical properties and corrosion resistance of friction-stir processed ultralight LA141 magnesium-lithium-aluminum alloy
- 28 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 1553-1571
Open AccessEnhanced mechanical properties and corrosion resistance of friction-stir processed ultralight LA141 magnesium-lithium-aluminum alloy
- 17 January 2024
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 39 (1) , 134-141
Improvement of Microstructure and Mechanical Properties of Rapid Cooling Friction Stir-welded A1050 Pure Aluminum
- 17 January 2024
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 39 (1) , 134-141
Improvement of Microstructure and Mechanical Properties of Rapid Cooling Friction Stir-welded A1050 Pure Aluminum
- 6 October 2023
- Published by Elsevier in Materials Today Communications
- Vol. 37
Effect of pre-corrosion on the cavitation erosion performance of two aluminum bronzes in 3.5% NaCl solution
- 6 October 2023
- Published by Elsevier in Materials Today Communications
- Vol. 37
Effect of pre-corrosion on the cavitation erosion performance of two aluminum bronzes in 3.5% NaCl solution