JYJun Yu

Jun Yu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jun Yu has a total of 83 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Shock wave reflections and blast load distribution in confined and vented cubic rooms

    by Pu Huo, Jun Yu, Banruo Li, Qiang Fu, Xiao Yu

    Internal explosions in rooms produce repeated shock reflections, strong load concentration near edges and corners, and complex overpressure-time histories. However, the relationship between changes induced by venting in reflected-wave propagation and the spatial distributions of peak overpressure and positive impulse remains insufficiently resolved. To address this gap, internal blast tests and high-fidelity computational fluid dynamics (CFD) simulations were conducted in a 2 × 2 × 2 m3 cubic reinforced concrete room. For centered detonation at a charge-weight-to-volume ratio of 12.5 g/m3, the maximum reflected overpressure at the front wall corner was ∼1.53 times that at the opposite back wall corner for a vent-area ratio (VAR) of 0.04. At VAR = 0.16, the difference between maximum reflected overpressures at the two corners decreased to 10.2%, while the positive impulse decreased over most of the wall. CFD results linked this contrast to two concurrent processes: changes in the reflecting boundary redistributed the early reflected peaks, while mass discharge accelerated the subsequent pressure decay. A higher-order image-source method for internal explosions reconstructed the pressure histories using geometrically screened reflection paths. It predicted maximum reflected overpressure and positive impulse with overall mean deviations of 8.7% and 10.9%, respectively, requiring ∼3–4 s per measurement point. Comparisons with a second-order image-source model further indicated that later reflections were more important for accumulated impulse than for maximum reflected overpressure.

  • Open Access

    A Dynamic Mesh Temporal Graph Network for Blast Load Prediction on Dynamic Unstructured Meshes

    by Banruo Li, Pu Huo, Jun Yu

    Accurate prediction of blast loads on structures is essential for blast-resistant design. Traditional high-fidelity numerical simulations remain computationally expensive, while existing data-driven approaches are often limited to fixed and structured meshes. To address these challenges, this study proposes a graph neural network–based method for blast load prediction on dynamic unstructured meshes. A Dynamic Mesh Temporal Graph Network (DMTG-Net) is developed, integrating a cross-mesh temporal alignment mechanism and physics-informed learning strategies. The cross-mesh alignment, implemented via a k-nearest neighbor-based mapping, enables consistent supervision under time-varying mesh topologies. In addition, dynamic graph construction incorporates propagation-time-aware edge features to reflect physical information transfer, and residual constraints derived from momentum and energy considerations are introduced to enhance physical consistency. Thereafter, a multi-scenario dataset is constructed based on experimentally validated computational fluid dynamics (CFD) simulations, including single-, double-, and triple-source detonation cases with adaptive mesh refinement. The proposed model achieves high prediction accuracy, with coefficient of determination (R²) values exceeding 0.99 in most cases, and effectively captures shock wave propagation, reflection, and interaction processes. Furthermore, the model demonstrates robust generalization capability under variations in detonation locations and moderate extrapolation of charge mass, accurately predicting key engineering quantities such as peak overpressure and arrival time. The results indicate that the proposed method provides an efficient and reliable surrogate modeling framework for blast load prediction in complex engineering scenarios involving dynamic meshes.

  • Open Access

    Physics-informed Graph Attention-Transformer networks for multi-scale residual displacement prediction in progressive collapse of RC frames

    by Jia-Hui Ni, Yi-Ping Gan, Ruiran Li, Shi-Lin Liang, Bo-Kun Yang, Jun Yu

    Nonlinear dynamic finite element analysis (FEA) is the mainstream method for assessing progressive collapse of structures, but its prohibitive computational cost limits rapid evaluation and decision support for damaged building systems. This paper proposes a physics-informed Graph Attention-Transformer (GAT-Transformer) framework as an engineering informatics surrogate for predicting ultimate residual displacements of reinforced concrete (RC) frames under progressive collapse. The framework transforms structural layouts, initial column-removal scenarios, and physical attributes into graph-based knowledge representations, where beam-column joints are modeled as nodes and physical members together with diagonal slab edges encode load-transfer paths and membrane actions. A local Graph Attention Network captures neighborhood force redistribution, while a global Graph Transformer with feature bypass learns long-range structural interactions and preserves macro-level descriptors. To address the scale imbalance between horizontal and vertical responses, a decoupled multi-head regression scheme is introduced for multi-scale displacement prediction. Trained and validated on 9968 parametric cases generated from high-fidelity simulations, the model achieves R2 = 0.953 on the validation set with a global MAE of 2.4 mm. Validation against full-scale blast tests on RC frames yields a relative error of 11.5%. The surrogate completes inference within 0.5 ms, delivering an eight-order-of-magnitude speed-up over high-fidelity FEA and enabling scalable graphical simulation, rapid post-disaster assessment, and decision support for collapse-risk evaluation in knowledge-intensive civil engineering assessment tasks.

  • Open Access

    Failure modes and assessment of S-UHPC-S composite panels under contact detonation

    by Yao Lu, Shi-Lin Liang, Jun Yu, Song-Lin Yue

    To investigate the influence of key parameters on the damage mechanism and failure modes of steel–ultra-high-performance concrete–steel (S-UHPC-S) composite panels subjected to contact detonation, four blast tests were conducted under a TNT charge of 2 kg. The results demonstrated that the panel thickness, the height-to-diameter ratio of the cylinder TNT, and the reinforcement ratio of the composite panel significantly affected the failure modes. As the panel thickness was decreased from 200 mm to 100 mm, the failure mode shifted from spalling failure to breaching failure. A smaller TNT height-to-diameter ratio led to an increased cratering depth but attenuated the overall damage severity. When the reinforcement ratio was decreased from 3% to 2%, the panel exhibited more severe damage, including fractured faceplate and crushed UHPC, and the corresponding failure mode shifted from spalling failure to punching failure. High-fidelity numerical models were then developed in LS-DYNA and validated against the experimental results. A series of parametric studies was subsequently conducted, considering variations in TNT equivalent, TNT height-to-diameter ratio, panel thickness, and reinforcement ratio. Based on the data from the experimental and numerical results and the geometric analysis of failure characteristics, a predictive method for failure modes and damage sizes was proposed. The method accounts for the effects of key influencing factors and demonstrate good accuracy. The results provide theoretical support for blast-resistant design and safety evaluation of S-UHPC-S composite panels under contact detonation.

  • Experimental Study on Structural Behavior of GFRP-Concrete-Steel Double-Skin Tubular Column under Near-Field Blast Load

    by Jun Yu, Yun Hao Geng, Xiao Wei Feng

    The newly developed hybrid FRP-concrete-steel double-skin tubular column (DSTC) integrates both high corrosion resistance and load-bearing capacity, enabling its potential for applications in high-temperature, high-humidity, and highly corrosive island environments, compared to traditional reinforced concrete or steel columns. However, from the perspective of multi-hazard mitigation, existing research on DSTC columns has predominantly focused on their static and seismic performance, while studies on the behavior of DSTCs under near-field blast load are scarce. In this paper, three glass fiber reinforced polymer (GFRP)-concrete-steel double-skin tubular columns (GFRP-DSTCs) were fabricated and tested under near-field explosion with same TNT equivalent but different scaled distances (ranging from 0.368 m/kg 1/3 to 0.240 m/kg 1/3 ). The GFRP tube was made through filament-wound technique and vinyl ester resins, and the glass fibers were oriented at ±80º with respect to the longitudinal axis of the column. The GFRP-DSTCs were installed in a field with bottom end fixed and top end simply supported. The results show that under near-field blast load, the damage to GFRP-DSTCs were concentrated in the region close the charge, where material failure and localized deformation were observed. When the scaled distance was 0.368 m/kg 1/3 , the specimens showed only localized inward bending, with the surface of the GFRP tube on the blast-facing surface subjected to the impact of detonation products, resulting in a roughened surface. Additionally, the localized surface turned black due to the explosion fireball and numerous circumferential cracks developed on the other area. While the scaled distance was 0.301 m/kg 1/3 , the specimen exhibited significant localized rupture of the GFRP tube at the blast-facing surface, accompanied by lamination along the thickness direction of the tube, and the concrete at the blast-facing surface was extensively crushed. As the scaled distance further decreased to 0.240 m/kg 1 /3 , the concrete crushing zone extended from the blast-facing surface to the entire side surface with the inner steel tube exposed and bent.