Farhad Razaghian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Farhad Razaghian has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Meisam Tahmasbi
Department of Electrical Engineering, South Tehran Branch, Islamic Azad University, Tehran, Iran
3 shared publicationsSobhan Roshani
Department of Electrical Engineering, Kermanshah Branch, Islamic Azad University, Kermanshah, Iran
3 shared publications- Mohammad Gholami
Department of Electrical Engineering, Faculty of Engineering and Technology, University of Mazandaran, Babolsar, Iran
2 shared publications Sobhan Sofimowloodi
Islamic Azad University
2 shared publications- Abdolhamid Akbarzadeh
Department of Bioresource Engineering McGill University Montreal Quebec Canada
1 shared publication - Ali Akbar Yousefi
Department of Plastics Engineering, Faculty of Polymer Processing Iran Polymer and Petrochemical Institute Tehran Iran
1 shared publication
Latest Publications
- 8 December 2022
- Published by Taylor & Francis in Molecular Simulation
- Vol. 49 (2) , 233-244
Modelling of basic reversible molecular logic gates and molecular full adder using a molecular diode model
- 8 December 2022
- Published by Taylor & Francis in Molecular Simulation
- Vol. 49 (2) , 233-244
Modelling of basic reversible molecular logic gates and molecular full adder using a molecular diode model
- 17 March 2022
- Published by Springer Nature in The Journal of Supercomputing
- Vol. 78 (11) , 13342-13372
Data block manipulation for error rate reduction in STT-MRAM based main memory
- 17 March 2022
- Published by Springer Nature in The Journal of Supercomputing
- Vol. 78 (11) , 13342-13372
Data block manipulation for error rate reduction in STT-MRAM based main memory
- 9 August 2021
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 109 (3) , 585-597
Design of bandpass–bandpass diplexers using rectangular-, T-, and L-shaped resonators for hybrid power amplifier and 5G applications
- 9 August 2021
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 109 (3) , 585-597
Design of bandpass–bandpass diplexers using rectangular-, T-, and L-shaped resonators for hybrid power amplifier and 5G applications
- 19 July 2021
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 75 (11-12) , 467-477
Design of high-efficiency Hybrid Power Amplifier with concurrent F&F−1 class operations for 5G application
This paper presents a novel structure of Hybrid Power Amplifier (HPA) to operate in two arbitrary classes of operation at two desirable frequencies. The proposed HPA is designed in concurrent F&F−1 classes, simultaneously for 5G application. Presented HPA can solve the harmonics interference problem for concurrent F and F−1 classes and also for any arbitrary class of operation in desired frequencies. The designed HPA operates at 1.5 GHz frequency in the F class mode, while operates at 2.1 GHz frequency in the F−1 class mode. A new method is presented by using two diplexers to provide two paths for signal in different frequencies. Two parallel paths are used at the output of the HPA circuit, so the proposed HPA can operate at two classes. Two diplexers are used in the HPA to make proper isolation between the designed paths. In design of the proposed HPA, according to the utilized diplexers, the amplifier can operate between two arbitrary classes of operation at desired frequencies without any specific switch. The measured drain efficiency (DE) and power added efficiency (PAE) parameters are 57 and 51%, respectively at 2.1 GHz, while measured DE and PAE are 64 and 54%, respectively at 1.5 GHz.
- 19 July 2021
- Published by Walter de Gruyter GmbH in Frequenz
- Vol. 75 (11-12) , 467-477
Design of high-efficiency Hybrid Power Amplifier with concurrent F&F−1 class operations for 5G application
This paper presents a novel structure of Hybrid Power Amplifier (HPA) to operate in two arbitrary classes of operation at two desirable frequencies. The proposed HPA is designed in concurrent F&F−1 classes, simultaneously for 5G application. Presented HPA can solve the harmonics interference problem for concurrent F and F−1 classes and also for any arbitrary class of operation in desired frequencies. The designed HPA operates at 1.5 GHz frequency in the F class mode, while operates at 2.1 GHz frequency in the F−1 class mode. A new method is presented by using two diplexers to provide two paths for signal in different frequencies. Two parallel paths are used at the output of the HPA circuit, so the proposed HPA can operate at two classes. Two diplexers are used in the HPA to make proper isolation between the designed paths. In design of the proposed HPA, according to the utilized diplexers, the amplifier can operate between two arbitrary classes of operation at desired frequencies without any specific switch. The measured drain efficiency (DE) and power added efficiency (PAE) parameters are 57 and 51%, respectively at 2.1 GHz, while measured DE and PAE are 64 and 54%, respectively at 1.5 GHz.
- 12 June 2020
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering: Imaging & Visualization
- Vol. 8 (6) , 631-640
A novel median based image impulse noise suppression system using spiking neurons on FPGA
The most common impulse noise suppression methods are based on the median filter. They are suitable for low noise densities, but employing a separate noise detection step makes them suitable for higher noise rates. Instead, this may degrade the performance for lower noise. Particularly, the adaptive median noise removal algorithm improves the results for both low and high noise corruption rates. This paper presents a novel noise detection and filtering algorithm that uses leaky integrate and fire spiking neurons which model natural computing of the brain. In the proposed method, at each process of the detection and the filtering, all pixels of an adaptive sliding window are fed to the spiking neurons performing the operations in parallel. As a result, higher processing speed and higher operating frequency are achieved. An FPGA is used to implement the algorithm due to its real-time application and reconfigurable structure. The proposed architecture represents a slight increase in the PSNR values, whereas it consumes less hardware resources compared to the previous works. The design is implemented on Cyclone IV device from Altera family. It includes 3231 LUTs and the maximum operating frequency of 187 MHz is achieved.
- 12 June 2020
- Published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering: Imaging & Visualization
- Vol. 8 (6) , 631-640
A novel median based image impulse noise suppression system using spiking neurons on FPGA
The most common impulse noise suppression methods are based on the median filter. They are suitable for low noise densities, but employing a separate noise detection step makes them suitable for higher noise rates. Instead, this may degrade the performance for lower noise. Particularly, the adaptive median noise removal algorithm improves the results for both low and high noise corruption rates. This paper presents a novel noise detection and filtering algorithm that uses leaky integrate and fire spiking neurons which model natural computing of the brain. In the proposed method, at each process of the detection and the filtering, all pixels of an adaptive sliding window are fed to the spiking neurons performing the operations in parallel. As a result, higher processing speed and higher operating frequency are achieved. An FPGA is used to implement the algorithm due to its real-time application and reconfigurable structure. The proposed architecture represents a slight increase in the PSNR values, whereas it consumes less hardware resources compared to the previous works. The design is implemented on Cyclone IV device from Altera family. It includes 3231 LUTs and the maximum operating frequency of 187 MHz is achieved.
- 4 February 2020
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 102 (3) , 541-554
A low-jitter clock multiplier using a simple low-power ECDLL with extra settled delays in VCDL
- 4 February 2020
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 102 (3) , 541-554
A low-jitter clock multiplier using a simple low-power ECDLL with extra settled delays in VCDL
- 24 August 2019
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 101 (1) , 99-107
Design of compact microstrip low pass filter using triangular and rectangular shaped resonator with ultra-wide stopband and sharp roll-off
- 24 August 2019
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 101 (1) , 99-107
Design of compact microstrip low pass filter using triangular and rectangular shaped resonator with ultra-wide stopband and sharp roll-off
- 8 October 2018
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 30 (2) , 279-291
Improving piezoelectric and pyroelectric properties of electrospun PVDF nanofibers using nanofillers for energy harvesting application
In this study, it was aimed to increase the piezoelectric and pyroelectric properties of electrospun polyvinylidene fluoride (PVDF) nanofibers simultaneously by using specific nanofillers. Graphene oxide (GO), graphene, and halloysite nanotubes with different concentrations (0, 0.05, 0.4, and 1.6% wt/wt) were combined with PVDF solution and were fabricated in the form of nanofibers through electrospinning. Pyroelectric properties of samples were measured by submerging sealed samples in hot water (360°K) and ice (270°K). The piezoelectric properties of the samples were evaluated through bending tests. The microstructural, mechanical, and thermal properties of the electrospun PVDF nanocomposite were investigated using scanning electron microscope, Instron instrument, and thermogravimetric analysis, respectively. To further support the experimental observations for generating electric voltage in the bended nanogenerator, the PVDF nanogenerator (PNG) was also modeled by a finite element analysis based on the theory of linear piezoelectricity using COMSOL Multiphysics simulation software. Experimental results showed that adding nanofillers could improve the piezoelectric and pyroelectric properties of all samples, associated with the increment of β‐phase in the nanofibers. It was concluded that adding nanofillers could increase pyroelectricity about 50% more than piezoelectricity in pristine PVDF nanofiber web. The PNG containing 1.6 wt% GO showed the highest efficiency in terms of piezoelectricity and pyroelectricity. In addition, the results showed that the ratio of piezoelectric to pyroelectric coefficients was constant (~1.5) and it was independent of the nanofiller type and content. The effect of external force and vibration frequency on the output voltage was also investigated. Increasing the compressive force and vibration frequency caused a greater output voltage. Finally, the fabricated nanogenerator was integrated on insole and elbow to investigate its energy harvesting capabilities from body movement.
- 8 October 2018
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 30 (2) , 279-291
Improving piezoelectric and pyroelectric properties of electrospun PVDF nanofibers using nanofillers for energy harvesting application
In this study, it was aimed to increase the piezoelectric and pyroelectric properties of electrospun polyvinylidene fluoride (PVDF) nanofibers simultaneously by using specific nanofillers. Graphene oxide (GO), graphene, and halloysite nanotubes with different concentrations (0, 0.05, 0.4, and 1.6% wt/wt) were combined with PVDF solution and were fabricated in the form of nanofibers through electrospinning. Pyroelectric properties of samples were measured by submerging sealed samples in hot water (360°K) and ice (270°K). The piezoelectric properties of the samples were evaluated through bending tests. The microstructural, mechanical, and thermal properties of the electrospun PVDF nanocomposite were investigated using scanning electron microscope, Instron instrument, and thermogravimetric analysis, respectively. To further support the experimental observations for generating electric voltage in the bended nanogenerator, the PVDF nanogenerator (PNG) was also modeled by a finite element analysis based on the theory of linear piezoelectricity using COMSOL Multiphysics simulation software. Experimental results showed that adding nanofillers could improve the piezoelectric and pyroelectric properties of all samples, associated with the increment of β‐phase in the nanofibers. It was concluded that adding nanofillers could increase pyroelectricity about 50% more than piezoelectricity in pristine PVDF nanofiber web. The PNG containing 1.6 wt% GO showed the highest efficiency in terms of piezoelectricity and pyroelectricity. In addition, the results showed that the ratio of piezoelectric to pyroelectric coefficients was constant (~1.5) and it was independent of the nanofiller type and content. The effect of external force and vibration frequency on the output voltage was also investigated. Increasing the compressive force and vibration frequency caused a greater output voltage. Finally, the fabricated nanogenerator was integrated on insole and elbow to investigate its energy harvesting capabilities from body movement.
- 23 June 2018
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 38 (2) , 498-511
Low-Power High-Frequency Phase Frequency Detector for Minimal Blind-Zone Phase-Locked Loops
- 23 June 2018
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 38 (2) , 498-511
Low-Power High-Frequency Phase Frequency Detector for Minimal Blind-Zone Phase-Locked Loops