António Castanhola Batista

The present work aims to verify whether the incremental hole-drilling technique (IHD), a widely accepted technique, is suitable for determining residual stresses in AISI 316L samples obtained by selective laser melting (SLM). The thermo-mechanical effects of cutting during the application of this technique can induce unwanted residual stresses due to the relatively low thermal conductivity of this material, leading to erroneous results. To accomplish this aim, a hybrid experimental-numerical method was implemented to analyze the ability of IHD to determine an imposed stress state. Experimentally, samples were subjected to a tensile calibration stress using a horizontal tensile test machine. To eliminate pre-existing residual stress, the samples were subjected to differential loads, instead of absolute ones. In this way, experimental strain-depth relaxation curves related to the imposed calibration stress were obtained. Based on the experimental data, IHD was numerically simulated using the finite element method. Numerical strain-depth relaxation curves, related to the same calibration stress used in the experimental study, were obtained. The comparison between the experimental and numerical strain-depth relaxation curves, as well as the stresses calculated using the so-called integral method for determining stresses via IHD, shows that IHD is a suitable technique for measuring residual stresses in additively manufactured AISI 316L samples.

The effect of the heat treatment on the residual stresses of welded cladded steel samples is analyzed in this study. The residual stresses across the plate’s square sections were determined using complementary methods; applying diffraction with neutron radiation and mechanically using the contour method. The analysis of the large coarse grain austenitic cladded layers, at the feasibility limits of diffraction methods, was only made possible by applying both methods. The samples are composed of steel plates, coated on one of the faces with stainless steel filler metals, this coating process, usually known as cladding, was carried out by submerged arc welding. After cladding, the samples were submitted to two different heat treatments with dissimilar parameters: one at a temperature of 620 °C maintained for 1 h and, the second at 540 °C, for ten hours. There was some difference in residual stresses measured by the two techniques along the surface of the coating in the as-welded state, although they are similar at the welding interface and in the heat-affected zone. The results also show that there is a residual stress relaxation for both heat-treated samples. The heat treatment carried out at a higher temperature showed sometimes more than 50% reduction in the initial residual stress values and has the advantage of being less time consuming, giving it an industrial advantage and making it more viable economically.

The aim of this work is to characterize the rolling and rolling-sliding contact fatigue failure mechanisms on the 32CrMoV13 nitrided steel. During rolling contact fatigue tests (RCF), two general features were observed: specimens presenting short lives and rough and sharpened spalling damage and specimens presenting long lives and only microspalling marks. It was possible to determine a contact fatigue limit of 3 GPa. During rolling-sliding contact fatigue tests (RSCF), a clearly different behaviour between the two specimens in contact has been observed: the driver shows circumferential and inclined cracks and only inclined cracks appear in the follower. This behaviour can be understood if the effect of the residual stress state in near-surface layers is considered. Before RCF tests, the residual stresses are compressive in all near-surface layers. After RCF tests, strong residual stress relaxation and even reversing behaviour was observed in the axial direction, which facilitates the surface crack initiation in the circumferential direction at rolling track borders.

This work is focused on understanding the significant factors affecting the fatigue strength of laser-welded butt joints in thin high-strength low-alloy (HSLA) steel. The effects of the weld profile, imperfections, hardness, and residual stresses were considered to explain the results found in the S-N curves of four welded series. The results showed acceptable fatigue strength although the welded series presented multiple-imperfections. The analysis of fatigue behavior at low stress levels through the stress-concentrating effect explained the influence of each factor on the S-N curves of the welded series. The fatigue limits of the welded series predicted through the stress-concentrating effect and by the relationship proposed by Murakami showed good agreement with the experimental results.

This review presents studies on iron meteorites (Campo del Cielo fall and an unregistered iron meteorite), an unregistered stony meteorite from Northwest Africa, and 13 tektites from the American, European, and Australasian strewn fields. The main experimental technique used in the studies was Mössbauer spectroscopy, both in transmission and backscattering geometries. For the latter, a MIMOS II spectrometer was used. Additionally, optical and scanning electron microscopies and X-ray diffraction were used. In the studied iron meteorites, kamacite is found as the main mineral. Campo del Cielo meteorite exhibits Widmanstätten patterns and schreibersite inclusions. The unregistered iron meteorite has Neumann lines and schreibersite inclusions. We have assigned Campo del Cielo as an octahedrite and the unregistered iron meteorite as a hexahedrite. The unregistered stony meteorite is composed mainly of iron-free silicates; at 4.2 K, the spectrum indicates maghemite and 1% troilite. The Cambodian tektite appeared individualized from other australasites, unlike the moldavite, which tends to cluster with them. Our analyses do not allow dismissing doubts on the provenance of tibetanites. The Fe³⁺/Fe²⁺ ratio was found to be higher for Muong Nong-type tektites than for splash-form tektites, as expected from their morphology and solidification from melt at lower temperature.

In this study local texture of process vessels made of carbon steel cladded by protective layers of stainless steel by submerged arc welding (SAW) were investigated by neutron diffraction using the diffractometer STRESSSPEC at FRM 2 (Garching, Germany). Different samples were prepared: as welded and as welded plus relevant industrial heat treatment. Local texture measurements with a gauge volume of 3 x 3 x 2 mm³ of the three cladding layers (at depths of 2 mm, 5 mm and 7.5 mm) for each sample were determined. Texture results indicated that there exists an annealed cube component in all the studied samples. Based on the measured pole figures at each depth and sample, the calculated orientation distribution functions data were used to calculate the Young's modulus with respect to the main welding directions. The calculated local and bulk anisotropic Young’s modulus in depth is presented and discussed.