Gennadiy Filimonikhin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gennadiy Filimonikhin has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Irina Filimonikhina
Central Ukrainian National Technical University
12 shared publications - Vladimir Pirogov
Central Ukrainian National Technical University
12 shared publications - Volodymyr Yatsun
Central Ukrainian National Technical University, Ukraine
11 shared publications - Andrey Nevdakha
Central Ukrainian National Technical University Universytetskyi ave., 8, Kropyvnytskyi, Ukraine, 25006
8 shared publications - Kostyantyn Dumenko
Central Ukrainian National Technical University Universytetskyi ave., 8, Kropivnitskiy, Ukraine, 25006
8 shared publications - Guntis Strautmanis
Riga Technical University
4 shared publications
Latest Publications
- 4 December 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 2 (12(43))
Justification of Methods for Determining Mass and Aerodynamic (Hydrodynamic) Unbalances of a Propeller
Gennadiy Filimonikhin, Professor, Doctor of Technical Sciences, Head of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-2819-0569, e-mail: filimonikhin@ukr.net Yulia Ostapchuk, PhD Student, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-7826-364X, e-mail: juli.biluk97@gmail.com Yulia Sokalska, PhD Student, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0008-4043-6251, e-mail: julija_8383@ukr.net Lubov Oliinichenko, Associate Professor, PhD, Associate Professor of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0001-9351-6265, e-mail: loga_lubov@ukr.net Volodymyr Pirogov, PhD, Associate Professor of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-5843-4552, e-mail: pirogovvv@ukr.net This paper theoretically substantiates new methods for determining the mass and aerodynamic (hydrodynamic) unbalance of a propeller, applicable to both air and water propellers with fixed pitch. It is proposed to determine the dynamic unbalance twice: first under normal operating conditions, and then under modified conditions in which only the aerodynamic (hydrodynamic) component changes. The proposed methods are based on: varying the density of air, gas, or liquid; applying reverse propeller rotation; and utilizing the ground effect. The aerodynamic (hydrodynamic) unbalance is quantified as a mass-equivalent unbalance, measured with a balancing instrument under defined operating conditions.
- 4 December 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 2 (12(43))
Justification of Methods for Determining Mass and Aerodynamic (Hydrodynamic) Unbalances of a Propeller
Gennadiy Filimonikhin, Professor, Doctor of Technical Sciences, Head of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-2819-0569, e-mail: filimonikhin@ukr.net Yulia Ostapchuk, PhD Student, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-7826-364X, e-mail: juli.biluk97@gmail.com Yulia Sokalska, PhD Student, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0008-4043-6251, e-mail: julija_8383@ukr.net Lubov Oliinichenko, Associate Professor, PhD, Associate Professor of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0001-9351-6265, e-mail: loga_lubov@ukr.net Volodymyr Pirogov, PhD, Associate Professor of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-5843-4552, e-mail: pirogovvv@ukr.net This paper theoretically substantiates new methods for determining the mass and aerodynamic (hydrodynamic) unbalance of a propeller, applicable to both air and water propellers with fixed pitch. It is proposed to determine the dynamic unbalance twice: first under normal operating conditions, and then under modified conditions in which only the aerodynamic (hydrodynamic) component changes. The proposed methods are based on: varying the density of air, gas, or liquid; applying reverse propeller rotation; and utilizing the ground effect. The aerodynamic (hydrodynamic) unbalance is quantified as a mass-equivalent unbalance, measured with a balancing instrument under defined operating conditions.
- 29 September 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 1 (12(43))
Modernization of the Influence Coefficient Method for Determining the Dynamic Unbalance of a Rigid Two-support Rotor
Gennadiy Filimonikhin, Professor, Doctor of Technical Sciences, Head of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: http://orcid.org/0000-0002-2819-0569, e-mail: filimonikhin@ukr.net Yuliia Sokalska, PhD student in Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0008-4043-6251, e-mail: julija_8383@ukr.net Yuliia Ostapchuk, PhD student in Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-7826-364X, e-mail: juli.biluk97@gmail.com The purpose of the work is to modernize the method of influence coefficients to increase the accuracy of determining the dynamic unbalance of a rigid two-support rotor. According to the modernized method, the rotor is installed on a balancing stand and the amplitudes and phases of the oscillations of the signals recorded from two single-axis vibration sensors during rotor rotation with a constant angular velocity are determined three times. The first time the rotor is rotated without adding test masses. The second time, a test mass is attached to the rotor in the first correction plane. The third time, a test mass is attached to the rotor in the second correction plane. After that, the relative values and relative positions of the unbalanced masses are calculated using complex coefficients in exponential form. The modulus of the complex number determines how many times the unbalanced mass in a certain correction plane is greater than the corresponding test mass. The angle sets the position of the unbalanced mass on the rotor and is counted from the test mass to the unbalanced mass in the direction of rotor rotation. Unbalanced masses are placed on the rotor at the same radius as the test masses. The modernized method uses in the calculations only the signals taken from two uniaxial vibration sensors and the phase sensor. The influence coefficients are not calculated explicitly. The values and locations of the test masses are not used in the calculations. This reduces the calculation errors, in particular, those caused by asynchronous data collection from the sensors.
- 29 September 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 1 (12(43))
Modernization of the Influence Coefficient Method for Determining the Dynamic Unbalance of a Rigid Two-support Rotor
Gennadiy Filimonikhin, Professor, Doctor of Technical Sciences, Head of the Department of Machine Parts and Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: http://orcid.org/0000-0002-2819-0569, e-mail: filimonikhin@ukr.net Yuliia Sokalska, PhD student in Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0008-4043-6251, e-mail: julija_8383@ukr.net Yuliia Ostapchuk, PhD student in Applied Mechanics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0002-7826-364X, e-mail: juli.biluk97@gmail.com The purpose of the work is to modernize the method of influence coefficients to increase the accuracy of determining the dynamic unbalance of a rigid two-support rotor. According to the modernized method, the rotor is installed on a balancing stand and the amplitudes and phases of the oscillations of the signals recorded from two single-axis vibration sensors during rotor rotation with a constant angular velocity are determined three times. The first time the rotor is rotated without adding test masses. The second time, a test mass is attached to the rotor in the first correction plane. The third time, a test mass is attached to the rotor in the second correction plane. After that, the relative values and relative positions of the unbalanced masses are calculated using complex coefficients in exponential form. The modulus of the complex number determines how many times the unbalanced mass in a certain correction plane is greater than the corresponding test mass. The angle sets the position of the unbalanced mass on the rotor and is counted from the test mass to the unbalanced mass in the direction of rotor rotation. Unbalanced masses are placed on the rotor at the same radius as the test masses. The modernized method uses in the calculations only the signals taken from two uniaxial vibration sensors and the phase sensor. The influence coefficients are not calculated explicitly. The values and locations of the test masses are not used in the calculations. This reduces the calculation errors, in particular, those caused by asynchronous data collection from the sensors.
- Open Access
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (7 (120)) , 45-53
Estimating the stability of steady motion of vibration machines operating on the somerfeld effect using an empirical method
One-, two-, and three-mass vibration machines with translational motion of platforms and a vibration exciter of a ball, roller, or pendulum type with several loads were studied. The empirical criterion for the onset of auto-balancing was applied in the extended formulation. It has been established that a single-mass vibration machine has one resonant speed, and: – at the after-resonance speeds of rotation of loads synchronously with the rotor, the auto-balancing mode becomes stable; – at the pre-resonance speeds of rotation of loads, loads tend to gather together. In a dual-mass vibration machine, there are two resonant speeds and one additional speed located between two resonant ones. The auto-balancing mode is stable when the loads rotate synchronously with the rotor at the following speeds: – between the first resonant speed and the additional speed; – greater than the second resonant speed. At other speeds of rotation of loads, loads tend to gather together. The three-mass vibration machine has three resonant speeds and two additional speeds, located one by one between adjacent resonant speeds. The auto-balancing mode is stable when the loads rotate synchronously with the rotor at the following speeds: – between the first resonant speed and the first additional speed; – between the second resonant speed and the second additional speed; – greater than the third resonant speed. At other speeds of rotation of loads, loads tend to gather together. In a single-mass vibration machine, the value of the resonant speed does not depend on the viscosity of supports. In dual-mass and three-mass vibration machines, all characteristic speeds depend on the viscosity of supports. With small forces of viscous resistance, the values of these speeds are close to the characteristic speeds found in the absence of resistance forces.
- 30 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (7 (120)) , 45-53
Open AccessEstimating the stability of steady motion of vibration machines operating on the somerfeld effect using an empirical method
One-, two-, and three-mass vibration machines with translational motion of platforms and a vibration exciter of a ball, roller, or pendulum type with several loads were studied. The empirical criterion for the onset of auto-balancing was applied in the extended formulation. It has been established that a single-mass vibration machine has one resonant speed, and: – at the after-resonance speeds of rotation of loads synchronously with the rotor, the auto-balancing mode becomes stable; – at the pre-resonance speeds of rotation of loads, loads tend to gather together. In a dual-mass vibration machine, there are two resonant speeds and one additional speed located between two resonant ones. The auto-balancing mode is stable when the loads rotate synchronously with the rotor at the following speeds: – between the first resonant speed and the additional speed; – greater than the second resonant speed. At other speeds of rotation of loads, loads tend to gather together. The three-mass vibration machine has three resonant speeds and two additional speeds, located one by one between adjacent resonant speeds. The auto-balancing mode is stable when the loads rotate synchronously with the rotor at the following speeds: – between the first resonant speed and the first additional speed; – between the second resonant speed and the second additional speed; – greater than the third resonant speed. At other speeds of rotation of loads, loads tend to gather together. In a single-mass vibration machine, the value of the resonant speed does not depend on the viscosity of supports. In dual-mass and three-mass vibration machines, all characteristic speeds depend on the viscosity of supports. With small forces of viscous resistance, the values of these speeds are close to the characteristic speeds found in the absence of resistance forces.
- Open Access
- 18 November 2022
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 46, 61-66
On the issue of the motion of balls in a double pendulum
The paper considers a model of a vertical double pendulum with one suspension centre moving in a vertical plane. For the proposed system of pendulums, differential equations of motion and conditions for the collision of balls are obtained. When modelling the movement of pendulums, the central impact of the balls was considered for various variants of the movement of the suspension point: the suspension point oscillates in the vertical direction; the suspension point makes rotational movements in the vertical plane. In this case, various conditions of the central impact between the balls were considered: absolutely inelastic impact; absolutely elastic impact; impact with the transformation of impact energy (elastic impact). Comparison of the results of the numerical simulation and the results of experiments with the Kapitza pendulum in published sources confirmed the possibility of modelling an elastic impact between balls in a double pendulum and between balls in an autobalancer with a horizontal axis of rotation of the rotor.
- 18 November 2022
- Published by JVE International Ltd. in Vibroengineering PROCEDIA
- Vol. 46, 61-66
Open AccessOn the issue of the motion of balls in a double pendulum
The paper considers a model of a vertical double pendulum with one suspension centre moving in a vertical plane. For the proposed system of pendulums, differential equations of motion and conditions for the collision of balls are obtained. When modelling the movement of pendulums, the central impact of the balls was considered for various variants of the movement of the suspension point: the suspension point oscillates in the vertical direction; the suspension point makes rotational movements in the vertical plane. In this case, various conditions of the central impact between the balls were considered: absolutely inelastic impact; absolutely elastic impact; impact with the transformation of impact energy (elastic impact). Comparison of the results of the numerical simulation and the results of experiments with the Kapitza pendulum in published sources confirmed the possibility of modelling an elastic impact between balls in a double pendulum and between balls in an autobalancer with a horizontal axis of rotation of the rotor.
- Open Access
- 31 October 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (7 (119)) , 96-104
Determining experimentally the patterns of the manifestation of the Sommerfeld effect in a ball auto-balancer
This paper proposes an experimental method for studying the Sommerfeld effect in auto-balancers or exciters of resonant vibrations of pendulum, ball, or roller type. The method is based on the processing of signals acquired from analog sensors of rotations and vibration acceleration using regression analysis. The method is tested on a specially designed rotor bench on isotropic viscoelastic supports, which executes spatial motion, and an auto-balancer with one ball. Checking the accuracy of the method using stroboscopic lighting demonstrates the accuracy of determining the speed of rotation of the rotor, ball, oscillation frequency of the rotor, etc. with an error of several hundredths of a percent. When fixing the ball relative to the rotor, a classic inertial vibration exciter is obtained. The rotor has two resonant velocities. The Sommerfeld effect is almost not manifested. With a gradual increase in the frequency of the current, the rotor speed increases monotonously. There is no significant slip or jump in the rotor speed. There are two distinct peaks on the amplitude-frequency characteristic. Therefore, such a vibration exciter is not suitable for the excitation of resonant vibrations. With the free placement of the ball in the oil, the behavior of the system changes significantly in the vicinity of the first resonant velocity. The first narrow resonant peak disappears in the roto. Instead, there is a long, gentle resonant rise. It lasts at a current frequency of 9.4 Hz to 19.3 Hz. The amplitude at the reference point on the resonant rise increases from 0.7 mm to 2.84 mm. Therefore, by changing the frequency of the current, it is possible to smoothly change the amplitude of the rotor oscillations by almost 4 times. The maximum amplitude of rotor oscillations is the same as at the first resonance with a fixed ball. Due to the gentleness of the resonant rise, a freely installed ball itself is a reliable exciter of resonant vibrations
- 31 October 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (7 (119)) , 96-104
Open AccessDetermining experimentally the patterns of the manifestation of the Sommerfeld effect in a ball auto-balancer
This paper proposes an experimental method for studying the Sommerfeld effect in auto-balancers or exciters of resonant vibrations of pendulum, ball, or roller type. The method is based on the processing of signals acquired from analog sensors of rotations and vibration acceleration using regression analysis. The method is tested on a specially designed rotor bench on isotropic viscoelastic supports, which executes spatial motion, and an auto-balancer with one ball. Checking the accuracy of the method using stroboscopic lighting demonstrates the accuracy of determining the speed of rotation of the rotor, ball, oscillation frequency of the rotor, etc. with an error of several hundredths of a percent. When fixing the ball relative to the rotor, a classic inertial vibration exciter is obtained. The rotor has two resonant velocities. The Sommerfeld effect is almost not manifested. With a gradual increase in the frequency of the current, the rotor speed increases monotonously. There is no significant slip or jump in the rotor speed. There are two distinct peaks on the amplitude-frequency characteristic. Therefore, such a vibration exciter is not suitable for the excitation of resonant vibrations. With the free placement of the ball in the oil, the behavior of the system changes significantly in the vicinity of the first resonant velocity. The first narrow resonant peak disappears in the roto. Instead, there is a long, gentle resonant rise. It lasts at a current frequency of 9.4 Hz to 19.3 Hz. The amplitude at the reference point on the resonant rise increases from 0.7 mm to 2.84 mm. Therefore, by changing the frequency of the current, it is possible to smoothly change the amplitude of the rotor oscillations by almost 4 times. The maximum amplitude of rotor oscillations is the same as at the first resonance with a fixed ball. Due to the gentleness of the resonant rise, a freely installed ball itself is a reliable exciter of resonant vibrations
- Open Access
- 30 June 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7(117)) , 68-76
Selection and research of stability of the steady state motions of a single-mass resonance vibromating machine working on the Somerfeld effect
This paper has defined and investigated for stability the steady state modes of motion of a single-mass resonant vibratory machine. The vibratory machine has a platform that is supported by viscoelastic supports. The platform moves rectilinearly translationally. A vibration exciter is installed on the platform. The vibration exciter consists of N identical loads – balls, rollers, or pendulums. The center of mass of each load can move in a circle of a certain radius with a center on the longitudinal axis of the rotor. Each load, when moving relative to the body of the vibration exciter, is exposed to a viscous resistance force. It was established theoretically that with small forces of viscous resistance and any number of loads, the vibratory machine has jamming modes under which the loads that are collected form a conditional combined load and lag behind the rotor. In this case, there are two bifurcation speeds of the rotor. At speeds less than the first bifurcation speed, the vibratory machine has one single (first) jamming mode. When the first bifurcation speed is exceeded, the second and third jamming modes appear. When the second bifurcation speed is exceeded, the first and second jamming modes disappear. The first jamming mode is resonant. In the cases of two or more loads, the vibratory machine also has an auto balancing mode (no vibrations), under which the loads rotate synchronously with the body of the vibration exciter and mutually balance each other. With small forces of viscous resistance, the computational experiment found that odd jamming modes are stable if they are numbered in ascending order of the frequency of load jamming. An auto-balancing mode is stable at the rotor speeds above the resonance. For the onset of a resonant mode of motion of the vibratory machine, it is enough to slowly accelerate the rotor to a speed lower than the second bifurcation speed. The results reported here are applicable in the design of resonant single-mass vibratory machines with inertial vibration exciters of the ball, roller, or pendulum type.
- 30 June 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7(117)) , 68-76
Open AccessSelection and research of stability of the steady state motions of a single-mass resonance vibromating machine working on the Somerfeld effect
This paper has defined and investigated for stability the steady state modes of motion of a single-mass resonant vibratory machine. The vibratory machine has a platform that is supported by viscoelastic supports. The platform moves rectilinearly translationally. A vibration exciter is installed on the platform. The vibration exciter consists of N identical loads – balls, rollers, or pendulums. The center of mass of each load can move in a circle of a certain radius with a center on the longitudinal axis of the rotor. Each load, when moving relative to the body of the vibration exciter, is exposed to a viscous resistance force. It was established theoretically that with small forces of viscous resistance and any number of loads, the vibratory machine has jamming modes under which the loads that are collected form a conditional combined load and lag behind the rotor. In this case, there are two bifurcation speeds of the rotor. At speeds less than the first bifurcation speed, the vibratory machine has one single (first) jamming mode. When the first bifurcation speed is exceeded, the second and third jamming modes appear. When the second bifurcation speed is exceeded, the first and second jamming modes disappear. The first jamming mode is resonant. In the cases of two or more loads, the vibratory machine also has an auto balancing mode (no vibrations), under which the loads rotate synchronously with the body of the vibration exciter and mutually balance each other. With small forces of viscous resistance, the computational experiment found that odd jamming modes are stable if they are numbered in ascending order of the frequency of load jamming. An auto-balancing mode is stable at the rotor speeds above the resonance. For the onset of a resonant mode of motion of the vibratory machine, it is enough to slowly accelerate the rotor to a speed lower than the second bifurcation speed. The results reported here are applicable in the design of resonant single-mass vibratory machines with inertial vibration exciters of the ball, roller, or pendulum type.
- Open Access
- 29 October 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (7 (113)) , 44-51
Determining the energy efficiency of a resonance single-mass vibratory machine whose operation is based on the Sommerfeld effect
This paper reports determining the energy efficiency of a vibratory machine consisting of a viscoelastically fixed platform that can move vertically, and a vibration exciter whose operation is based on the Sommerfeld effect. The body of the vibration exciter rotates at a steady angular speed while there are the same loads in the form of a ball, a roller, or a pendulum inside it. The load, being moved relative to the body, is exposed to the forces of viscous resistance, which are internal within the system. It was established that under the steady oscillatory modes of a vibratory machine's movement, the loads are tightly pressed to each other, thereby forming a combined load. Energy is productively spent on platform oscillations and unproductively dissipated due to the movement of the combined load relative to the body. With an increase in the speed of the body rotation, the increasing internal forces of viscous resistance bring the speed of rotation of the combined load closer to the resonance speed, and the amplitude of platform oscillations increases. However, the combined load, in this case, increasingly lags behind the body, which increases unproductive energy loss and decreases the efficiency of the vibratory machine. A purely resonant motion mode of the vibratory machine produces the maximum amplitude of platform oscillations, the dynamic factor, the total power of viscous resistance forces. In this case, the efficiency reaches its minimum value. To obtain vigorous oscillations of the platform with a simultaneous increase in the efficiency of the vibratory machine, it is necessary to reduce the forces of viscous resistance in supports with a simultaneous increase in the internal forces of viscous resistance. An algorithm for calculating the basic dynamic characteristics of the vibratory machine's oscillatory motion has been built, based on solving the problem parametrically. The accepted parameter is the angular speed at which a combined load gets stuck. The effectiveness of the algorithm has been illustrated using a specific example
- 29 October 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (7 (113)) , 44-51
Open AccessDetermining the energy efficiency of a resonance single-mass vibratory machine whose operation is based on the Sommerfeld effect
This paper reports determining the energy efficiency of a vibratory machine consisting of a viscoelastically fixed platform that can move vertically, and a vibration exciter whose operation is based on the Sommerfeld effect. The body of the vibration exciter rotates at a steady angular speed while there are the same loads in the form of a ball, a roller, or a pendulum inside it. The load, being moved relative to the body, is exposed to the forces of viscous resistance, which are internal within the system. It was established that under the steady oscillatory modes of a vibratory machine's movement, the loads are tightly pressed to each other, thereby forming a combined load. Energy is productively spent on platform oscillations and unproductively dissipated due to the movement of the combined load relative to the body. With an increase in the speed of the body rotation, the increasing internal forces of viscous resistance bring the speed of rotation of the combined load closer to the resonance speed, and the amplitude of platform oscillations increases. However, the combined load, in this case, increasingly lags behind the body, which increases unproductive energy loss and decreases the efficiency of the vibratory machine. A purely resonant motion mode of the vibratory machine produces the maximum amplitude of platform oscillations, the dynamic factor, the total power of viscous resistance forces. In this case, the efficiency reaches its minimum value. To obtain vigorous oscillations of the platform with a simultaneous increase in the efficiency of the vibratory machine, it is necessary to reduce the forces of viscous resistance in supports with a simultaneous increase in the internal forces of viscous resistance. An algorithm for calculating the basic dynamic characteristics of the vibratory machine's oscillatory motion has been built, based on solving the problem parametrically. The accepted parameter is the angular speed at which a combined load gets stuck. The effectiveness of the algorithm has been illustrated using a specific example
- Open Access
- 17 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7(112)) , 60-66
Theoretical study into the aerodynamic imbalance of a propeller blade and the correcting masses to balance it
This paper reports the theoretically investigated aerodynamic imbalance of the propeller blade, as well as correcting masses for balancing it. It has been established that the aerodynamic forces acting on the propeller blade can be balanced by the adjustment of masses. This is also true for the case of compressed air (gas) provided that the blades are streamlined by laminar flow. That makes it possible to use rotor balancing methods to study the aerodynamic forces acting on the propeller blade. The rotating blade mainly generates torque aerodynamic imbalance due to a lift force. A much smaller static component of the aerodynamic imbalance is formed by the drag force acting on the blade. The correcting mass located in the propeller plane balances both static and torque components of the aerodynamic imbalance in its correction plane. A second correcting mass (for example, on the electric motor shank) balances the torque component of aerodynamic imbalance in its correction plane. The calculations are simplified under the assumption that the equilibrium of aerodynamic forces is perpendicular to the chord of the blade. For approximate calculations, one can use information about the approximate location of the pressure center. The aerodynamic forces acting on the blade can be determined on the basis of the correcting masses that balance them. The accuracy in determining the aerodynamic forces could be improved by measuring a lift force. The computational experiment has confirmed the theoretical results formulated above. The experiment further proves the possibility of applying the devised theory for propellers whose rotation speed changes with a change in the angles of blade installation. The findings reported here could be used both for devising methods of propeller balancing and for constructing methods to study the aerodynamic forces acting on the blade.
- 17 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7(112)) , 60-66
Open AccessTheoretical study into the aerodynamic imbalance of a propeller blade and the correcting masses to balance it
This paper reports the theoretically investigated aerodynamic imbalance of the propeller blade, as well as correcting masses for balancing it. It has been established that the aerodynamic forces acting on the propeller blade can be balanced by the adjustment of masses. This is also true for the case of compressed air (gas) provided that the blades are streamlined by laminar flow. That makes it possible to use rotor balancing methods to study the aerodynamic forces acting on the propeller blade. The rotating blade mainly generates torque aerodynamic imbalance due to a lift force. A much smaller static component of the aerodynamic imbalance is formed by the drag force acting on the blade. The correcting mass located in the propeller plane balances both static and torque components of the aerodynamic imbalance in its correction plane. A second correcting mass (for example, on the electric motor shank) balances the torque component of aerodynamic imbalance in its correction plane. The calculations are simplified under the assumption that the equilibrium of aerodynamic forces is perpendicular to the chord of the blade. For approximate calculations, one can use information about the approximate location of the pressure center. The aerodynamic forces acting on the blade can be determined on the basis of the correcting masses that balance them. The accuracy in determining the aerodynamic forces could be improved by measuring a lift force. The computational experiment has confirmed the theoretical results formulated above. The experiment further proves the possibility of applying the devised theory for propellers whose rotation speed changes with a change in the angles of blade installation. The findings reported here could be used both for devising methods of propeller balancing and for constructing methods to study the aerodynamic forces acting on the blade.
- Open Access
- 17 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (111)) , 51-58
The dynamics of a resonance single-mass vibratory machine with a vibration exciter of targeted action that operates on the Sommerfeld effect
This paper reports a study into the dynamics of a vibratory machine composed of a viscoelastically-fixed platform that can move vertically and two identical inertial vibration exciters. The vibration exciters' bodies rotate at the same angular velocities in opposite directions. The bodies host a single load in the form of a ball, roller, or pendulum. The loads' centers of mass can move relative to the bodies in a circle with a center on the axis of rotation. The loads' relative movements are hindered by the forces of viscous resistance. It was established that a vibratory machine theoretically possesses the following: – one to three oscillatory modes of movement under which loads get stuck at almost constant angular velocity and generate total unbalanced mass in the vertical direction only; – a no-oscillation mode under which loads rotate synchronously with the bodies and generate total unbalanced mass in the horizontal direction only. At the same time, only one oscillatory mode is resonant and exists at the above-the-resonance speeds of body rotation, lower than some characteristic speed. At the bodies' rotation speeds: ‒ pre-resonant; there is a globally asymptotically stable (the only existing) mode of load jams; ‒ above-the-resonance, lower than the characteristic velocity; there are locally asymptotically stable regimes ‒ both the resonance mode of movement of a vibratory machine and a no-oscillations mode; ‒ exceeding the characteristic velocity: there is a globally asymptotically stable no-oscillations mode. Computational experiments have confirmed the results of theoretical research. At the same time, it was additionally established that it would suffice, to enter a resonant mode of movement, to slowly accelerate the bodies of vibration exciters to the above-the-resonance speed, less than the characteristic speed. The results reported here could be interesting both for the theory and practice of designing new vibratory machines
- 17 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (111)) , 51-58
Open AccessThe dynamics of a resonance single-mass vibratory machine with a vibration exciter of targeted action that operates on the Sommerfeld effect
This paper reports a study into the dynamics of a vibratory machine composed of a viscoelastically-fixed platform that can move vertically and two identical inertial vibration exciters. The vibration exciters' bodies rotate at the same angular velocities in opposite directions. The bodies host a single load in the form of a ball, roller, or pendulum. The loads' centers of mass can move relative to the bodies in a circle with a center on the axis of rotation. The loads' relative movements are hindered by the forces of viscous resistance. It was established that a vibratory machine theoretically possesses the following: – one to three oscillatory modes of movement under which loads get stuck at almost constant angular velocity and generate total unbalanced mass in the vertical direction only; – a no-oscillation mode under which loads rotate synchronously with the bodies and generate total unbalanced mass in the horizontal direction only. At the same time, only one oscillatory mode is resonant and exists at the above-the-resonance speeds of body rotation, lower than some characteristic speed. At the bodies' rotation speeds: ‒ pre-resonant; there is a globally asymptotically stable (the only existing) mode of load jams; ‒ above-the-resonance, lower than the characteristic velocity; there are locally asymptotically stable regimes ‒ both the resonance mode of movement of a vibratory machine and a no-oscillations mode; ‒ exceeding the characteristic velocity: there is a globally asymptotically stable no-oscillations mode. Computational experiments have confirmed the results of theoretical research. At the same time, it was additionally established that it would suffice, to enter a resonant mode of movement, to slowly accelerate the bodies of vibration exciters to the above-the-resonance speed, less than the characteristic speed. The results reported here could be interesting both for the theory and practice of designing new vibratory machines
- Open Access
- 30 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (7 (110)) , 66-73
Analytical study of auto-balancing within the framework of the flat model of a rotor and an auto-balancer with a single cargo
This paper reports the analytically established conditions for the onset of auto-balancing for the case of a flat rotor model on isotropic elastic-viscous supports and an auto-balancer with a single load. The rotor is statically unbalanced, the rotation axis is vertical. The auto-balancer has a single cargo – a pendulum, a ball, or a roller. The balancing capacity of the cargo is equal to the rotor imbalance. The physical-mathematical model of the system is described. The differential equations of motion are recorded in dimensionless form relative to the coordinate system that rotates synchronously with the rotor. The so-called main movement has been found; in it, the cargo synchronously rotates with the rotor and balances it. The differential equations of motion are linearized in the neighborhood of the main movement. A characteristic equation has been constructed. It helped investigate the stability of the main movement (an auto-balancing mode) for the cases of the absence and presence of resistance forces in the system. It was established that in the absence of resistance forces in the system: – the rotor has three characteristic rotational speeds, and the first always coincides with the resonance frequency; – auto-balancing occurs when the rotor rotates at speeds between the first and second ones, and above the third characteristic speed; – the value of the second and third characteristic speeds is significantly influenced by the ratio of weight to the mass of the system; – the second and third characteristic speeds monotonously increase with an increase in the ratio of cargo weight to the mass of the system. Resistance forces significantly affect both the values of the second and third characteristic speeds and the conditions of their existence. Small resistance forces do not change the quality behavior of the system. With high resistance forces, the number of characteristic speeds decreases to one. The paper reports the results applicable to an auto-balancer with many cargoes when it balances the imbalance that equals the balancing capacity of the auto-balancer
- 30 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (7 (110)) , 66-73
Open AccessAnalytical study of auto-balancing within the framework of the flat model of a rotor and an auto-balancer with a single cargo
This paper reports the analytically established conditions for the onset of auto-balancing for the case of a flat rotor model on isotropic elastic-viscous supports and an auto-balancer with a single load. The rotor is statically unbalanced, the rotation axis is vertical. The auto-balancer has a single cargo – a pendulum, a ball, or a roller. The balancing capacity of the cargo is equal to the rotor imbalance. The physical-mathematical model of the system is described. The differential equations of motion are recorded in dimensionless form relative to the coordinate system that rotates synchronously with the rotor. The so-called main movement has been found; in it, the cargo synchronously rotates with the rotor and balances it. The differential equations of motion are linearized in the neighborhood of the main movement. A characteristic equation has been constructed. It helped investigate the stability of the main movement (an auto-balancing mode) for the cases of the absence and presence of resistance forces in the system. It was established that in the absence of resistance forces in the system: – the rotor has three characteristic rotational speeds, and the first always coincides with the resonance frequency; – auto-balancing occurs when the rotor rotates at speeds between the first and second ones, and above the third characteristic speed; – the value of the second and third characteristic speeds is significantly influenced by the ratio of weight to the mass of the system; – the second and third characteristic speeds monotonously increase with an increase in the ratio of cargo weight to the mass of the system. Resistance forces significantly affect both the values of the second and third characteristic speeds and the conditions of their existence. Small resistance forces do not change the quality behavior of the system. With high resistance forces, the number of characteristic speeds decreases to one. The paper reports the results applicable to an auto-balancer with many cargoes when it balances the imbalance that equals the balancing capacity of the auto-balancer