Selda Oterkus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Selda Oterkus has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Erkan Oterkus
Department of Naval Architecture, Ocean and Marine Engineering, University of Strathclyde, Glasgow G4 0LZ, UK
29 shared publications Erkan Oterkus
PeriDynamics Research Centre, University of Strathclyde, Glasgow, UK
17 shared publicationsErdogan Madenci
8 shared publications- Zhenghao Yang
Department of Mechanical Engineering, National Taiwan University, Taipei, Taiwan
6 shared publications - Cagan Diyaroglu
University of Arizona, Tucson
5 shared publications - Satoyuki Tanaka
Hiroshima University
5 shared publications
Latest Publications
- Open Access
- 10 January 2026
- Published by Springer Nature in Journal of Peridynamics and Nonlocal Modeling
- Vol. 8 (1) , 1
A New Bond Specific Energy-Based Failure Criterion for Peridynamics
One of the most important characteristics of peridynamics is its capability of predicting how cracks initiate and propagate in materials and structures. Definition of failure in peridynamics is different than classical approaches due to non-local feature of peridynamics. In this study, a new failure criterion, named as bond specific energy-based failure criterion, is introduced. Moreover, an in-depth investigation of different failure criteria used in peridynamic framework is presented. Three different failure criteria are considered including the widely used critical stretch failure criterion, critical energy failure criterion, and the newly introduced bond specific energy-based failure criterion. Numerical results demonstrated that new bond specific energy-based failure criterion shows better performance in capturing expected bond breakage with respect to other approaches. In addition, it can also accurately predict failure load for different crack lengths during crack propagation.
- 10 January 2026
- Published by Springer Nature in Journal of Peridynamics and Nonlocal Modeling
- Vol. 8 (1) , 1
Open AccessA New Bond Specific Energy-Based Failure Criterion for Peridynamics
One of the most important characteristics of peridynamics is its capability of predicting how cracks initiate and propagate in materials and structures. Definition of failure in peridynamics is different than classical approaches due to non-local feature of peridynamics. In this study, a new failure criterion, named as bond specific energy-based failure criterion, is introduced. Moreover, an in-depth investigation of different failure criteria used in peridynamic framework is presented. Three different failure criteria are considered including the widely used critical stretch failure criterion, critical energy failure criterion, and the newly introduced bond specific energy-based failure criterion. Numerical results demonstrated that new bond specific energy-based failure criterion shows better performance in capturing expected bond breakage with respect to other approaches. In addition, it can also accurately predict failure load for different crack lengths during crack propagation.
- Open Access
- 24 December 2025
- Published by Nan Yang Academy of Sciences Pte Ltd in Sustainable Marine Structures
- p. 233-254
Finite Element Modelling of Hydrogen Embrittlement by Considering Hydrogen Coverage Boundary Conditions
In this study, an alternative modelling approach for absorbed hydrogen stress corrosion cracking (SCC) is proposed, with hydrogen-enhanced decohesion (HEDE) identified as the key failure mechanism. All analyses have been performed by utilising only ABAQUS standard elements, COH2D4T and CPE4T, already available within the software and without the need to develop external subroutines. The study also tends to highlight the criticality of implementing a correct Traction Separation Law (TSL) curve to simulate the hydrogen diffusion within the specimen and using the concept of dynamic hydrogen penetration by continuously updating the hydrogen concentration boundary conditions as the crack propagates. In conclusion, this study successfully demonstrated that standard software elements (COH2D4T and CPE4T) can effectively model physical problems and crack velocity propagation without custom subroutines. It emphasized that while the specific shape of the Traction-Separation Law (TSL) is less critical, its correct implementation is vital for simulating dynamic hydrogen coverage. Crucially, excluding this dynamic coverage—a common practice—risks significantly underestimating crack propagation speed. Although results incorporating dynamic coverage aligned well with experimental data, minor discrepancies are likely due to unmodeled factors like material property variations, hydrogen trapping, temperature, and granular microstructure, which are proposed for future research.
- 24 December 2025
- Published by Nan Yang Academy of Sciences Pte Ltd in Sustainable Marine Structures
- p. 233-254
Open AccessFinite Element Modelling of Hydrogen Embrittlement by Considering Hydrogen Coverage Boundary Conditions
In this study, an alternative modelling approach for absorbed hydrogen stress corrosion cracking (SCC) is proposed, with hydrogen-enhanced decohesion (HEDE) identified as the key failure mechanism. All analyses have been performed by utilising only ABAQUS standard elements, COH2D4T and CPE4T, already available within the software and without the need to develop external subroutines. The study also tends to highlight the criticality of implementing a correct Traction Separation Law (TSL) curve to simulate the hydrogen diffusion within the specimen and using the concept of dynamic hydrogen penetration by continuously updating the hydrogen concentration boundary conditions as the crack propagates. In conclusion, this study successfully demonstrated that standard software elements (COH2D4T and CPE4T) can effectively model physical problems and crack velocity propagation without custom subroutines. It emphasized that while the specific shape of the Traction-Separation Law (TSL) is less critical, its correct implementation is vital for simulating dynamic hydrogen coverage. Crucially, excluding this dynamic coverage—a common practice—risks significantly underestimating crack propagation speed. Although results incorporating dynamic coverage aligned well with experimental data, minor discrepancies are likely due to unmodeled factors like material property variations, hydrogen trapping, temperature, and granular microstructure, which are proposed for future research.
- Open Access
- 22 December 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 221
A novel peridynamic cylindrical shell formulation
- 22 December 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 221
Open AccessA novel peridynamic cylindrical shell formulation
- Open Access
- 16 December 2025
- Published by Nan Yang Academy of Sciences Pte Ltd in Sustainable Marine Structures
- p. 193-232
Systematic Review of Functionally Graded Pipelines and Proposal of a New Material Property Variation to Enhance Operational Stability
The global discussion surrounding Functionally Graded Materials (FGMs) highlights their unique and diverse micro-material properties that result from varying two or more materials in a strategic combination profile. These combinations produce distinct physical and chemical characteristics. Changes in these characteristics may occur continuously, referred to as a gradient function, or discontinuously as a stepwise function. The changes can appear within homogeneous or heterogeneous material geometries. The variation in material properties depends on the volume fraction index function. This variation can occur in 1D, 2D, or 3D, either in the thickness or length direction within a material model. The vacuum in the review study on mechanically toughened and thermally resistant Functionally Graded (FG) pipelines prompted the current review study. This study addresses the absence of an appropriate variational function for FG cylindrical pipelines. It proposes a gradation function pattern to improve pipeline structural performance. An appraisal based on relevant FGM literature was conducted to improve the temperature differentials in traditional composite materials and stress-related issues in carbon steel pipelines. The review identifies specific FGM property variations that reduce failures that are possible in conventional materials. Reviewed articles and evaluation procedures followed the 2020 PRISMA guidelines. Literature was obtained from Scopus, Connected Papers, and other reputable sources. The study also discusses potential FG pipelines for gas and green energy transportation. The reviewed literature establishes the context for this research and addresses the gap in 3D FG model variation functions involving multiple materials.
- 16 December 2025
- Published by Nan Yang Academy of Sciences Pte Ltd in Sustainable Marine Structures
- p. 193-232
Open AccessSystematic Review of Functionally Graded Pipelines and Proposal of a New Material Property Variation to Enhance Operational Stability
The global discussion surrounding Functionally Graded Materials (FGMs) highlights their unique and diverse micro-material properties that result from varying two or more materials in a strategic combination profile. These combinations produce distinct physical and chemical characteristics. Changes in these characteristics may occur continuously, referred to as a gradient function, or discontinuously as a stepwise function. The changes can appear within homogeneous or heterogeneous material geometries. The variation in material properties depends on the volume fraction index function. This variation can occur in 1D, 2D, or 3D, either in the thickness or length direction within a material model. The vacuum in the review study on mechanically toughened and thermally resistant Functionally Graded (FG) pipelines prompted the current review study. This study addresses the absence of an appropriate variational function for FG cylindrical pipelines. It proposes a gradation function pattern to improve pipeline structural performance. An appraisal based on relevant FGM literature was conducted to improve the temperature differentials in traditional composite materials and stress-related issues in carbon steel pipelines. The review identifies specific FGM property variations that reduce failures that are possible in conventional materials. Reviewed articles and evaluation procedures followed the 2020 PRISMA guidelines. Literature was obtained from Scopus, Connected Papers, and other reputable sources. The study also discusses potential FG pipelines for gas and green energy transportation. The reviewed literature establishes the context for this research and addresses the gap in 3D FG model variation functions involving multiple materials.
- Open Access
- 10 September 2025
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 64 (1) , 50-64
A peridynamic framework for ice–structure interaction: modelling rate-dependent ice fracture under impact loading
- 10 September 2025
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 64 (1) , 50-64
Open AccessA peridynamic framework for ice–structure interaction: modelling rate-dependent ice fracture under impact loading
- Open Access
- 25 August 2025
- Published by Elsevier in Progress in Aerospace Sciences
- Vol. 157
Progress in inverse finite element method for aerospace structural health monitoring applications
- 25 August 2025
- Published by Elsevier in Progress in Aerospace Sciences
- Vol. 157
Open AccessProgress in inverse finite element method for aerospace structural health monitoring applications
- Open Access
- 14 August 2025
- Published by Nan Yang Academy of Sciences Pte Ltd in Sustainable Marine Structures
- p. 177–208
A Detailed Structural Review of Onshore and Offshore Pipelines Containing Defects
This study presents a thorough and holistic review of various studies focusing on the structural analysis of Oil and Gas (O&G) pipelines, with an emphasis on various defect modes. The study appraised pipeline-related articles from the empirical, semi-empirical, analytical, and numerical studies. However, the study's core objective remains to address the persistent challenge that often leads to Burst Pressure Loss (BPL) in a pipeline. These mechanical-associated damages, which can result in BPL, may include pipe scratches, dents, or cracks. Therefore, training a large volume of datasets in neural network architectures or the finite element domain is crucial in this context. The study further explores previous research to gain a deeper insight into how many modes of damage enhance loss in Burst Pressure (BP). The study further synthesises significant reasons why pipeline Structural Health Failures (SHFs) occur, as drawn from existing literature. Failure scenarios in pipeline dent, crack, fracture, buckling, fatigue, corrosion, BPL, and Third-Party Damage (TPD) could result from mechanical deformation, ageing, insufficient real-time monitoring, and TPD influences. Many of the assessed articles conclude that the experimental approach and Finite Element Method (FEM) are valid and can accurately validate one another in the analysis and prediction of pipeline failures. However, this study offers valuable and comprehensive resources for pipeline engineers, academic researchers, and industry professionals. Again, the study is crucial for pipeline fabricators, installers, and operators to keep up with maintenance, repairs, and predictions.
- 14 August 2025
- Published by Nan Yang Academy of Sciences Pte Ltd in Sustainable Marine Structures
- p. 177–208
Open AccessA Detailed Structural Review of Onshore and Offshore Pipelines Containing Defects
This study presents a thorough and holistic review of various studies focusing on the structural analysis of Oil and Gas (O&G) pipelines, with an emphasis on various defect modes. The study appraised pipeline-related articles from the empirical, semi-empirical, analytical, and numerical studies. However, the study's core objective remains to address the persistent challenge that often leads to Burst Pressure Loss (BPL) in a pipeline. These mechanical-associated damages, which can result in BPL, may include pipe scratches, dents, or cracks. Therefore, training a large volume of datasets in neural network architectures or the finite element domain is crucial in this context. The study further explores previous research to gain a deeper insight into how many modes of damage enhance loss in Burst Pressure (BP). The study further synthesises significant reasons why pipeline Structural Health Failures (SHFs) occur, as drawn from existing literature. Failure scenarios in pipeline dent, crack, fracture, buckling, fatigue, corrosion, BPL, and Third-Party Damage (TPD) could result from mechanical deformation, ageing, insufficient real-time monitoring, and TPD influences. Many of the assessed articles conclude that the experimental approach and Finite Element Method (FEM) are valid and can accurately validate one another in the analysis and prediction of pipeline failures. However, this study offers valuable and comprehensive resources for pipeline engineers, academic researchers, and industry professionals. Again, the study is crucial for pipeline fabricators, installers, and operators to keep up with maintenance, repairs, and predictions.
- Open Access
- 18 July 2025
- Published by Wiley in International Journal of Mechanical System Dynamics
- Vol. 5 (3) , 495-517
Monitoring of Corrosion Damage by Using iFEM Methodology
Marine environment is a harsh environment that can cause major issues for marine structures while operating in this environment, including fatigue cracking and corrosion damage, which can yield catastrophic consequences, such as human life losses, financial losses, environmental pollution, and so forth. Therefore, it is critical to take necessary actions before undesired situations happen. One potential solution is to install structural health monitoring systems on marine structures. Structural health monitoring is a technology to enhance the safety, stability, and functionality of large engineering structures. The inverse Finite Element Method (iFEM) is a promising technique for this purpose. In this study, the corrosion damage detection capability of iFEM is presented by introducing two new damage parameters for plates under tension and bending loading conditions. The contribution of newly introduced parameters to the accuracy of iFEM on damage detection is demonstrated for multiple corrosion scenarios and sensor configurations.
- 18 July 2025
- Published by Wiley in International Journal of Mechanical System Dynamics
- Vol. 5 (3) , 495-517
Open AccessMonitoring of Corrosion Damage by Using iFEM Methodology
Marine environment is a harsh environment that can cause major issues for marine structures while operating in this environment, including fatigue cracking and corrosion damage, which can yield catastrophic consequences, such as human life losses, financial losses, environmental pollution, and so forth. Therefore, it is critical to take necessary actions before undesired situations happen. One potential solution is to install structural health monitoring systems on marine structures. Structural health monitoring is a technology to enhance the safety, stability, and functionality of large engineering structures. The inverse Finite Element Method (iFEM) is a promising technique for this purpose. In this study, the corrosion damage detection capability of iFEM is presented by introducing two new damage parameters for plates under tension and bending loading conditions. The contribution of newly introduced parameters to the accuracy of iFEM on damage detection is demonstrated for multiple corrosion scenarios and sensor configurations.
- Open Access
- 7 July 2025
- Published by Taylor & Francis in Advanced Manufacturing: Polymer & Composites Science
- Vol. 11 (1)
Experimental investigation of thickness effects in the manufacture of thick-section composite structures using liquid thermoplastic resin
- 7 July 2025
- Published by Taylor & Francis in Advanced Manufacturing: Polymer & Composites Science
- Vol. 11 (1)
Open AccessExperimental investigation of thickness effects in the manufacture of thick-section composite structures using liquid thermoplastic resin
- Open Access
- 8 April 2025
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 231
Structural health monitoring of shell structures with preexisting cracks
- 8 April 2025
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 231
Open AccessStructural health monitoring of shell structures with preexisting cracks