Lin He
Research Subjects
Lin He has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Yefei Li
4 shared publicationsYimin Gao
4 shared publicationsZhiwei Liu
4 shared publicationsWenyan Zhai
3 shared publicationsWeiyao Zhang
2 shared publications- Wentao Yan
Department of Mechanical Engineering, National University of Singapore, Singapore, Singapore
2 shared publications
Latest Publications
- 15 July 2025
- Published by Elsevier in Acta Biomaterialia
- Vol. 203, 1-20
Partially degradable Ti-Mg composites for biomedical applications: Recent advances and future perspectives
- 15 July 2025
- Published by Elsevier in Acta Biomaterialia
- Vol. 203, 1-20
Partially degradable Ti-Mg composites for biomedical applications: Recent advances and future perspectives
- 6 December 2023
- Published by Elsevier in Measurement
- Vol. 225, 113989
Cutting performance and cutting fluid infiltration characteristics into tool-chip interface during MQL milling
- 6 December 2023
- Published by Elsevier in Measurement
- Vol. 225, 113989
Cutting performance and cutting fluid infiltration characteristics into tool-chip interface during MQL milling
- 1 October 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 806, 1-10
Effect of rare earth Y addition on the microstructure and mechanical properties of Ti(C,N)-304ss cermets
- 1 October 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 806, 1-10
Effect of rare earth Y addition on the microstructure and mechanical properties of Ti(C,N)-304ss cermets
- 1 June 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 790, 20-26
Abnormal oxidation behavior of Fe in Ti(C,N)-304ss cermet during early oxidation stage
- 1 June 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 790, 20-26
Abnormal oxidation behavior of Fe in Ti(C,N)-304ss cermet during early oxidation stage
- 25 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (7) , 076506
Influence of Cr addition on tribological properties of bulk Fe2B under dry friction and water lubrication
In the present study, friction and wear properties of bulk Fe2B with different Cr additions were examined under dry friction and water lubrication conditions. The morphology, structure, mechanical properties and tribological properties were investigated by OM, SEM, XRD and XPS. The results show that there is no obvious new phase generated and the crystal structure has no changes with Cr addition. Cr element solubilizes in Fe2B gains without any segregation, only bits of (Fe, Cr)2B crystals formed. With the increasing of Cr addition, the fracture toughness increases first then decreases, and 2Cr sample has the highest toughness. Under dry friction condition, the friction coefficient and wear loss are all decrease first and then increase. 2Cr sample has the highest friction coefficient and wear loss. The tribochemical products form a lubricating film to reduce the friction coefficient and wear loss. And the wear mechanism is mainly brittle fracture. Under water lubrication condition, the friction coefficient drops remarkably, then slightly rises up. In contrast, the wear loss increases first and then decreases. 2Cr sample has the lowest friction coefficient, but the highest wear loss. The wear mechanism is mainly tribo-chemical wear in water. A comparison of the results under dry friction and water lubrication conditions, for the same sample, the friction coefficient is lower, but the wear loss is higher in water.
- 25 June 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (7) , 076506
Influence of Cr addition on tribological properties of bulk Fe2B under dry friction and water lubrication
In the present study, friction and wear properties of bulk Fe2B with different Cr additions were examined under dry friction and water lubrication conditions. The morphology, structure, mechanical properties and tribological properties were investigated by OM, SEM, XRD and XPS. The results show that there is no obvious new phase generated and the crystal structure has no changes with Cr addition. Cr element solubilizes in Fe2B gains without any segregation, only bits of (Fe, Cr)2B crystals formed. With the increasing of Cr addition, the fracture toughness increases first then decreases, and 2Cr sample has the highest toughness. Under dry friction condition, the friction coefficient and wear loss are all decrease first and then increase. 2Cr sample has the highest friction coefficient and wear loss. The tribochemical products form a lubricating film to reduce the friction coefficient and wear loss. And the wear mechanism is mainly brittle fracture. Under water lubrication condition, the friction coefficient drops remarkably, then slightly rises up. In contrast, the wear loss increases first and then decreases. 2Cr sample has the lowest friction coefficient, but the highest wear loss. The wear mechanism is mainly tribo-chemical wear in water. A comparison of the results under dry friction and water lubrication conditions, for the same sample, the friction coefficient is lower, but the wear loss is higher in water.
- 1 March 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (3) , 036516
Effect of milling time on powder’s structure evolution of Ti(C,N)-304 stainless steel cermet
- 1 March 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (3) , 036516
Effect of milling time on powder’s structure evolution of Ti(C,N)-304 stainless steel cermet
- 1 February 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (2) , 026507
Effect of milling time on the microstructure and mechanical properties of Ti(C,N)-304 stainless steel cermet
- 1 February 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (2) , 026507
Effect of milling time on the microstructure and mechanical properties of Ti(C,N)-304 stainless steel cermet
- 1 May 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 693, 1067-1073
Influence of Edge Preparation Parameters on the Cutting Edge in Drag Finishing
Tool edge preparation can eliminate defects and realize hone cutting edge, which can improve the quality of the workpiece surface, elevate the stability of cutting process and the tool life. In order to better investigate the edge preparation mechanism, the influence law of the edge preparation process parameters on the cutting edge is analyzed. The paper presents the single factor experiments and orthogonal experiments with the cemented carbide milling tool spindle rotation rate, edge preparation time, abrasive size and abrasive ratio in drag finishing. The edge preparation mechanism is revealed in the paper, which provides basis for the structure optimization of cutting edge contour.
- 1 May 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 693, 1067-1073
Influence of Edge Preparation Parameters on the Cutting Edge in Drag Finishing
Tool edge preparation can eliminate defects and realize hone cutting edge, which can improve the quality of the workpiece surface, elevate the stability of cutting process and the tool life. In order to better investigate the edge preparation mechanism, the influence law of the edge preparation process parameters on the cutting edge is analyzed. The paper presents the single factor experiments and orthogonal experiments with the cemented carbide milling tool spindle rotation rate, edge preparation time, abrasive size and abrasive ratio in drag finishing. The edge preparation mechanism is revealed in the paper, which provides basis for the structure optimization of cutting edge contour.
- 1 August 1994
- Published by Elsevier in Enzyme and Microbial Technology
- Vol. 16 (8) , 696-702
Evaluation of catalytic activity and synergism between two xylanase isoenzymes in enzymic hydrolysis of two separate xylans in different states of solubility
- 1 August 1994
- Published by Elsevier in Enzyme and Microbial Technology
- Vol. 16 (8) , 696-702
Evaluation of catalytic activity and synergism between two xylanase isoenzymes in enzymic hydrolysis of two separate xylans in different states of solubility